sounds like my S1 is not firing on all 4 cylinders...why?
sounds like my S1 is not firing on all 4 cylinders...why?
Author
Discussion

minimax

Original Poster:

11,985 posts

287 months

Wednesday 23rd May 2007
quotequote all
hi chaps, I have recently noticed (ie from yesterday morning) that my Elise under anything more than the most feather light of feather light touches of acceleration is firing only on 3 cylinders...



why could this be?



it idles on all 4, but as soon as you pull away from a junction or similar it goes in to 3 cylinder mode...I feel like throwing the god damn thing away it's so irritating!



when this used to happen on my old mini it was always as a result of water on the dizzy or spark plugs, could it be the same on the Elise? I did wash the car on sunday....



I unscrewed the case that covers the spark plugs and left it off overnight (the car lives on the drive) to dry out but no joy, if anything it was worse this morning frown



is my diagnosis correct guys?



thanks.

rfoster

1,482 posts

285 months

Wednesday 23rd May 2007
quotequote all
Sounds like water in the spark plug wells. There's no point just taking the cover off, they could collect more condensation overnight. Get a nice wad of kitchen roll, fold it so it's long & thin and stuff it down around the spark plugs to see if there is any moisture in there. Chances are it'll be in the plug well 2nd from left. If this is the case then simply dry it out as much as you can.



You can stop this happening by running some silicone sealant along the edges of the spark plug cover strip so it's sealed in - but it's a relatively minor things so don't thin I'd bother.

Sam_68

9,939 posts

276 months

Wednesday 23rd May 2007
quotequote all
Almost certainly ignition related, but could be several different things... damp, dodgy spark plug lead, dodgy spark plug, dodgy distributor cap.

minimax

Original Poster:

11,985 posts

287 months

Wednesday 23rd May 2007
quotequote all
nice work chaps, that is helpful. I think i'll struggle it home tonight and investigate the plug holes a bit with some kitchen towel...been racking my brains over this for hours!



thumbup

greysquirrel

786 posts

258 months

Wednesday 23rd May 2007
quotequote all
mine suffered this after a massive downpour... take the spark plug out, stick kitchen roll down and use the lead housing to push it right to the bottom, will probably pick up a load of water and hey presto, fixed. bloody annoying though.

sp60

524 posts

290 months

Wednesday 23rd May 2007
quotequote all
erm, I'd have a go at getting rid of the water before removing the plug. If you take the plug out and there is water in there, its going straight into your engine, which isn't good.

You could try taking the cover off and going for a long drive. The hot temperature and increased airflow should shift most of it. Then give the plug leads a reseating when the engines cooled down a bit.

minimax

Original Poster:

11,985 posts

287 months

Wednesday 23rd May 2007
quotequote all
good point, I think i'll stuff kitchem towel down the spark tubes fish about a bit then go for a drive and hope!



smile

greysquirrel

786 posts

258 months

Wednesday 23rd May 2007
quotequote all
lol, i meant take the HT lead out, not the actual spark plug! lol dont go sticking kitchen roll down the hole wink

it just seems to settle at the bottom and even the slightest few spots of condensation seem to make it misfire.I ended up just changing the leads.

minimax

Original Poster:

11,985 posts

287 months

Wednesday 23rd May 2007
quotequote all
I noticed it only after I washed the car, and I do remember sloshing an unusually large amount of water over the boot and thinking..."hmmm"



...looks like my worries were well founded!



frown



well, a little bit of work followed by silicone sealant will sort it I hope biggrin

crackthatoff

3,314 posts

244 months

Wednesday 23rd May 2007
quotequote all
I was looking for you on sunday, take it you washed the car for the event? You didn't miss anything spectacular, infact it was fairly crap really.

felt a little intimidated with all the vx's there, there were only about 6 of us !

bod27

230 posts

244 months

Wednesday 23rd May 2007
quotequote all
My S1 every now and then starts to misfire, it seems to be the HT lead coming loose, a quick push back in sorts it out untill next time, might get some new leads one day.

minimax

Original Poster:

11,985 posts

287 months

Tuesday 29th May 2007
quotequote all
banghead

right, turns out after having taken apart the ignition setup a best I could and cleaned/WD-40'd it...that it made no difference.

I happened to fill up with petrol from the local Total garage (had 17 litres in, filled it to 30odd) and...problem gone. completely.

so, dodgy petrol was to blame rage

oh well, at least I know whom not to use in future.

thanks for all your help people!

Tom

NWTony

3,011 posts

259 months

Tuesday 29th May 2007
quotequote all
Worth sealing the screw holes in the engine cover with silicon sealant as well, the perceived wisdowm is that the water gets into the spark plugs through these.

minimax

Original Poster:

11,985 posts

287 months

Tuesday 29th May 2007
quotequote all
good call, I have so far sealed up the cover but will do the screw holes as well! smile

minimax

Original Poster:

11,985 posts

287 months

Tuesday 29th May 2007
quotequote all
NWTony said:
Worth sealing the screw holes in the engine cover with silicon sealant as well, the perceived wisdowm is that the water gets into the spark plugs through these.