Elise hub conversion to 100mm PCD
Discussion
Hello
Don't venture up here often but then it dawned on me that all you Lotus Elise type people may have an answer to a problem I am facing.
We put a K Series in the back of a car we build, the fronts hubs are 100mm PCD rears because of drive train is 95.25 becuase of the MGF running gear, got round it on the prototype by using mini parts but now we are using the VVC it won't stay together with min CV's.
We have found an adapter, http://www.eliseparts.com/shop/index.php?main_page... but wondered whether anyone had machined up some replacement drive flanges? anyone tried these adapters? any other solutions out there?
The car we build weighs in at 550kg and is slightly related to Lotus as it was designed by Frank Costin, loads of details on website in profile.
Cheers
Joe
Don't venture up here often but then it dawned on me that all you Lotus Elise type people may have an answer to a problem I am facing.
We put a K Series in the back of a car we build, the fronts hubs are 100mm PCD rears because of drive train is 95.25 becuase of the MGF running gear, got round it on the prototype by using mini parts but now we are using the VVC it won't stay together with min CV's.
We have found an adapter, http://www.eliseparts.com/shop/index.php?main_page... but wondered whether anyone had machined up some replacement drive flanges? anyone tried these adapters? any other solutions out there?
The car we build weighs in at 550kg and is slightly related to Lotus as it was designed by Frank Costin, loads of details on website in profile.
Cheers
Joe
Hi Joe
Yes I have flanges already made though they are racing spec and not cheap.
They are constructed from EN19T and have both studs patterns machined in as standard.
The rear is sculptured to save weight and aid cooling by throwing air outward.
The fronts are even lighter and have a short bolt kit to go with them if required.
These were originally made for my own 2.4 Honda conversion so I also have these with Honda splines.
Between them they save about a kilo of unsprung and rotational mass and are about 2.5 X stronger than the Rover items.
They were designed to last and not have to be replaced every 2 bearing changes due to scoring!
They have no extra offset of course so can take most wheels.
Prices are £129 for the Rover splined rears, £125 for the Honda splined rears and £99 for the fronts.
14mm or 16mm bolt kits with SS thrust washers are available £24.
All in stock, in Bangkok at the moment but if you are in a hurry I can have them sent out.
If you are pushing in excess of 350 BHP you may wish to consider the Honda splined flanges that take the HondaR CV.

Gaz
Yes I have flanges already made though they are racing spec and not cheap.
They are constructed from EN19T and have both studs patterns machined in as standard.
The rear is sculptured to save weight and aid cooling by throwing air outward.
The fronts are even lighter and have a short bolt kit to go with them if required.
These were originally made for my own 2.4 Honda conversion so I also have these with Honda splines.
Between them they save about a kilo of unsprung and rotational mass and are about 2.5 X stronger than the Rover items.
They were designed to last and not have to be replaced every 2 bearing changes due to scoring!
They have no extra offset of course so can take most wheels.
Prices are £129 for the Rover splined rears, £125 for the Honda splined rears and £99 for the fronts.
14mm or 16mm bolt kits with SS thrust washers are available £24.
All in stock, in Bangkok at the moment but if you are in a hurry I can have them sent out.
If you are pushing in excess of 350 BHP you may wish to consider the Honda splined flanges that take the HondaR CV.

Gaz
Edited by Gaz again on Wednesday 30th May 22:00
Gassing Station | Elise/Exige/Europa/340R | Top of Page | What's New | My Stuff


