'Tis the season...
Discussion
the ambient outside temperature does seem to make a difference... during the winter when sat in traffic, the frog's temp reading would usually stay fairly static... during the summer, it rockets up into the low 90's when the fan kicks in... this surely must have some long-term effect on the head gasket?
It is a design fault - on three counts.
Firstly, the thermostat is in the wrong place for the cooling system layout, particularly on the Elise (and, incidentally, the MGF!). When the thermostat opens, the engine suffers a sudden rush of very cool water into the head and puts the top of the engine through a rather severe temperature cycle. This causes contraction and expansion that often results in HGF.
Secondly, the locating of the head on the block was a poor design. Nylon dowels will never provide a sufficiently rigid location for a light alloy head going through continual temperature cycles and a block twisting under fairly high torque loads.
Thirdly, the original gasket design didn't leave much margin for error - and unfortunately, errors are exactly what it has to endure!
The good news is that all are relatively cheap to fix. A well designed pressure relief thermostat in the outflow from the head will provide a far kinder cooling environment for the engine, steel dowels keep the head in place, and double sided head gaskets provide a far more resilient and flexible seal.
Firstly, the thermostat is in the wrong place for the cooling system layout, particularly on the Elise (and, incidentally, the MGF!). When the thermostat opens, the engine suffers a sudden rush of very cool water into the head and puts the top of the engine through a rather severe temperature cycle. This causes contraction and expansion that often results in HGF.
Secondly, the locating of the head on the block was a poor design. Nylon dowels will never provide a sufficiently rigid location for a light alloy head going through continual temperature cycles and a block twisting under fairly high torque loads.
Thirdly, the original gasket design didn't leave much margin for error - and unfortunately, errors are exactly what it has to endure!
The good news is that all are relatively cheap to fix. A well designed pressure relief thermostat in the outflow from the head will provide a far kinder cooling environment for the engine, steel dowels keep the head in place, and double sided head gaskets provide a far more resilient and flexible seal.
Edited by Talkwrench on Sunday 10th June 13:28
Edited by Talkwrench on Sunday 10th June 13:44
It does seem that there are seasonal variations. In the winter, a lot of radiators seem to go - perhaps the extremes of water tem contribute to splits in the plastic endcaps of the radiator.
Summer - I am not sure why - the thermal shock is probably worse in winter. Mine has been a bit suspicious since January, but under road driving is absolutely fine. It only had problems on track under high load. Still, a few hundred quid to fix at the same time that I need a C service means that the experience will only cost a couple of hundred quid more than I would have paid for the c service. That is if I wasn't having other stuff done....
The engines are otherwise pretty robust. If the PRT has been designed ito the system and rover had sorted liner heights from the factory, HGF would be almost unheard of in the K. In fact it would be seen as a light and fairly "bulletproof" engine.
Similarly, if the yota had a better oil pump, it would probably also not have experienced the failures it has. I would choose a £700 HGF over a £7K new engine every time considering the abuse mine gets on track. It has been buzzed to 9K and was fine appart from the gearbox shrapnel. (not me driving BTW) Cost £70 for me to buy and fit a 2nd hand gearbox with less mileage than my old one.
Summer - I am not sure why - the thermal shock is probably worse in winter. Mine has been a bit suspicious since January, but under road driving is absolutely fine. It only had problems on track under high load. Still, a few hundred quid to fix at the same time that I need a C service means that the experience will only cost a couple of hundred quid more than I would have paid for the c service. That is if I wasn't having other stuff done....
The engines are otherwise pretty robust. If the PRT has been designed ito the system and rover had sorted liner heights from the factory, HGF would be almost unheard of in the K. In fact it would be seen as a light and fairly "bulletproof" engine.
Similarly, if the yota had a better oil pump, it would probably also not have experienced the failures it has. I would choose a £700 HGF over a £7K new engine every time considering the abuse mine gets on track. It has been buzzed to 9K and was fine appart from the gearbox shrapnel. (not me driving BTW) Cost £70 for me to buy and fit a 2nd hand gearbox with less mileage than my old one.
Talkwrench said:
It is a design fault - on three counts.
Firstly, the thermostat is in the wrong place for the cooling system layout, particularly on the Elise (and, incidentally, the MGF!). When the thermostat opens, the engine suffers a sudden rush of very cool water into the head and puts the top of the engine through a rather severe temperature cycle. This causes contraction and expansion that often results in HGF.
Secondly, the locating of the head on the block was a poor design. Nylon dowels will never provide a sufficiently rigid location for a light alloy head going through continual temperature cycles and a block twisting under fairly high torque loads.
Thirdly, the original gasket design didn't leave much margin for error - and unfortunately, errors are exactly what it has to endure!
The good news is that all are relatively cheap to fix. A well designed pressure relief thermostat in the outflow from the head will provide a far kinder cooling environment for the engine, steel dowels keep the head in place, and double sided head gaskets provide a far more resilient and flexible seal.
We all know about the fundamental design faults. That doesnt tell why they tend to go at the beginning of summer / end of spring. 3-4 well used cars that are driven hard and well maintained, they are driven all through the year, all go in the same week. We had the same sort of thing last year.Firstly, the thermostat is in the wrong place for the cooling system layout, particularly on the Elise (and, incidentally, the MGF!). When the thermostat opens, the engine suffers a sudden rush of very cool water into the head and puts the top of the engine through a rather severe temperature cycle. This causes contraction and expansion that often results in HGF.
Secondly, the locating of the head on the block was a poor design. Nylon dowels will never provide a sufficiently rigid location for a light alloy head going through continual temperature cycles and a block twisting under fairly high torque loads.
Thirdly, the original gasket design didn't leave much margin for error - and unfortunately, errors are exactly what it has to endure!
The good news is that all are relatively cheap to fix. A well designed pressure relief thermostat in the outflow from the head will provide a far kinder cooling environment for the engine, steel dowels keep the head in place, and double sided head gaskets provide a far more resilient and flexible seal.
Edited by Talkwrench on Sunday 10th June 13:28
Edited by Talkwrench on Sunday 10th June 13:44
Why
What has happened in the last week or so to make gaskets leak? If it was thermal shock then this would be more pronounced in winter / spring, if it was height of temp then it would be August.....
Gooby said:
What has happened in the last week or so to make gaskets leak? If it was thermal shock then this would be more pronounced in winter / spring, if it was height of temp then it would be August.....
I am not sure that it is all in the same week. Stu blew the radiator tank cap off back in March - that suggests the problem was already there back then. Piooly sounds like his problems have aso been ongoing. FWIW I knew mine was gone more than a month ago.Mine was causing problems as far back as January, but I couldn't prove HGF (still can't), but its obvious that it is.
I suppose now that the weather is better, people are driving the cars harder and the symptoms are manifesting, whereas tiptoeing about in the wet / cold, there was less likelihood of pressurised gases entering the cooling system - something that usually happens at high rpm / load.
Because the process of developing HGF is a gradual one, it could manifest at any time. Theoretically it would seem nore likely that the process happens more rapidly during the winter months, but perhaps it is the hard driving on track etc which is bringing to light the effects of a process that has been ongoing for months.
Edited by shangani on Sunday 10th June 17:38
Well my car is all fixed now. Managed to complete the whole job in 3 evenings work, 14 hours in total which isnt bad for my first ever attempt. I reckon I do it in half the time now I know what I'm doing. My temper was tested many times when I couldnt get enough access to certain bolts etc. I changed the thermostat too for a 82 degree one instead of the standard 87. The car now runs at a rock steady 80 degrees although I am taking it easy at the moment.
Are there any rules on running in? Stuart was told 300 miles at no more than 2500 rpm. Does this need to be done? I've been driving mine around all weekend and not gone over 3000 rpm, but driving a lump sport 160 at under 3000rpm is challenge in its own right !!!!
Are there any rules on running in? Stuart was told 300 miles at no more than 2500 rpm. Does this need to be done? I've been driving mine around all weekend and not gone over 3000 rpm, but driving a lump sport 160 at under 3000rpm is challenge in its own right !!!!
piooly said:
Well my car is all fixed now. Managed to complete the whole job in 3 evenings work, 14 hours in total which isnt bad for my first ever attempt. I reckon I do it in half the time now I know what I'm doing. My temper was tested many times when I couldnt get enough access to certain bolts etc. I changed the thermostat too for a 82 degree one instead of the standard 87. The car now runs at a rock steady 80 degrees although I am taking it easy at the moment.
Are there any rules on running in? Stuart was told 300 miles at no more than 2500 rpm. Does this need to be done? I've been driving mine around all weekend and not gone over 3000 rpm, but driving a lump sport 160 at under 3000rpm is challenge in its own right !!!!
Miles only told us to do that because it was a new type of composite gasket from landrover and that was the instructions on the packet!! I would suggest you take it realativley easy for a few miles though! But you are right its fecking hard!!Are there any rules on running in? Stuart was told 300 miles at no more than 2500 rpm. Does this need to be done? I've been driving mine around all weekend and not gone over 3000 rpm, but driving a lump sport 160 at under 3000rpm is challenge in its own right !!!!
Gooby said:
Talkwrench said:
It is a design fault - on three counts.
And everything else what I said......
We all know about the fundamental design faults. That doesnt tell why they tend to go at the beginning of summer / end of spring. 3-4 well used cars that are driven hard and well maintained, they are driven all through the year, all go in the same week. We had the same sort of thing last year.And everything else what I said......
Why
What has happened in the last week or so to make gaskets leak? If it was thermal shock then this would be more pronounced in winter / spring, if it was height of temp then it would be August.....
My guess is that it happens as soon as the sun is out, the roads are dry and every Elise owner stops being sensibly cautious on slippery roads!
boobles said:
What is PRT & how does it perevent HGF & how much does it cost?
I wouldn't say it prevents, theres cases over on SELOC with PRTS fitted and they have still got HGFs. Its a Pressure Relief Thermostat (also known as the PRT).http://wiki.seloc.org/a/Pressure_Relief_Remote_The...
Though not necessarily preventing HGF if the damage is already done, it can certainly ease the stress on the gasket and may well prevent the failure if no damage is present.
More relevant is the fitment of a PRT kit during/after head gasket replacement to try and make sure it doesnt happen again!
More relevant is the fitment of a PRT kit during/after head gasket replacement to try and make sure it doesnt happen again!
Edited by Talkwrench on Sunday 10th June 22:39
Gassing Station | Elise/Exige/Europa/340R | Top of Page | What's New | My Stuff





