Fitting an oil temp gauge
Fitting an oil temp gauge
Author
Discussion

Andy T

Original Poster:

468 posts

259 months

Wednesday 20th June 2007
quotequote all
how easy (or not) is it to fit an oil temperature gauge? Is it something I could do myself or am I likely to cause a big oily mess?

I've managed to fit a hurricane induction kit with no problems so thats about my level of mechanical skill.

Cheers

fatboy111

308 posts

248 months

Wednesday 20th June 2007
quotequote all
Did someone get a new tool kit for his birthday? hehe

Andy T

Original Poster:

468 posts

259 months

Thursday 21st June 2007
quotequote all
Certainly did! Hey, It only took me 2 hours to fit the Hurricane! Makes the car about 2 tons lighter too, AND I saved a few nuts and bolts along the way! smile

I've been reading about how you shouldn't rag your engine until the oils warm but theres no way of knowing what temp it is without a temp gauge.

What is the correct "spirited" driving oil temp anyway?


cej

961 posts

253 months

Thursday 21st June 2007
quotequote all
When I tune race cars we wait until the oil reaches around 75 degrees Celcius before we go above 3000 rpm. It does take a considerable time to get there compared to the water temperature.

Beachbum

2,610 posts

262 months

Thursday 21st June 2007
quotequote all
Most peoples rule of thumb is, wait until water temp is at usual operating temp for the car, then wait an additional 10mins for the oil to catch up.

Phil-CH

1,132 posts

295 months

Thursday 21st June 2007
quotequote all
I'm not sure, but from what I was told, it isn't a very easy job to fit an oil temp gauge. Besides the sensor that has to be fitted, a path has to be drilled into the cabin for the wiring to the gauge. If you want it in one of the air-vents as I had mine fitted too, you have to get the wire through there and fit the gauge. No idea how they did it, but it doesn't look like a very easy job to me.

Cheers Phil

Andy T

Original Poster:

468 posts

259 months

Thursday 21st June 2007
quotequote all
Phil-CH said:
I'm not sure, but from what I was told, it isn't a very easy job to fit an oil temp gauge. Besides the sensor that has to be fitted, a path has to be drilled into the cabin for the wiring to the gauge. If you want it in one of the air-vents as I had mine fitted too, you have to get the wire through there and fit the gauge. No idea how they did it, but it doesn't look like a very easy job to me.

Cheers Phil
Phil, Did you have yours fitted at a dealer? How much did it set you back? You got any pictures of it installed?

Cheers

Andy

Phil-CH

1,132 posts

295 months

Thursday 21st June 2007
quotequote all
Andy T said:
Phil, Did you have yours fitted at a dealer? How much did it set you back? You got any pictures of it installed?

Cheers

Andy
It's a 2 channel SPA gauge. Channel 1 is oil-temp, Channel 2 (in my case) is induction air temp after charge-cooler (most use channel 2 for oil-pressure).



It was fitted by Bemani when I had the S/C fitted (together with a baffled oilsump) and other parts, so the price was more or less offset by the work that was done in those areas for the other parts. Don't quote me on this, but I think the stand-alone price would be around 1000-1500 CHF (making that around £400-600).

I'm fairly confident any (Lotus) dealer could and would fit a oil-temp gauge such as mine on demand... I simply had it done through Bemani because they were already doing extensive work on my car.

ludo

5,308 posts

235 months

Thursday 21st June 2007
quotequote all
This approach looks fairly straightforward as it uses the existing display and all the wiring is in the engine compartment, but the dowsnside is that the fog light switch is used to toggle between water and oil temperature.

http://www.fourwheels.org/elise/oil-temp/ 

I'm tempted to have this done, but to do the wiring properly and use the dummy switch already on the dashboard.

Andy T

Original Poster:

468 posts

259 months

Thursday 21st June 2007
quotequote all
Cheers for the Pic Phil that looks good!

As for the http://www.fourwheels.org/elise/oil-temp/

Yeah that would be good but it looks a bit too complex for me to attempt myself. I would have thought it would be a relatively straightforward job to add a gauge though.

Cheers