S1 wheel bearing change
S1 wheel bearing change
Author
Discussion

jamiebae

Original Poster:

6,245 posts

242 months

Friday 6th July 2007
quotequote all
I need to change the front drivers side wheel bearing on my '99 S1, how easy is it to do? Any specialist tools needed or should I just get a garage to do it?

Cheers!

TheYeti

656 posts

247 months

Friday 6th July 2007
quotequote all
Very hard work and I eventually got the garage to do it as you need a very strong press to get it out. Get the hub off and take it to a garage that will be able to press it out for you. Won't cost you much........

jamiebae

Original Poster:

6,245 posts

242 months

Friday 6th July 2007
quotequote all
Sounds like a good idea, I might strip it down at the weekend then smile

AdrianR

822 posts

315 months

Friday 6th July 2007
quotequote all
As the man says, you need a big press so best to remove hub DIY and then take to friendly garage. Manual says the hub should be heated before bearing is removed/replaced to expand it slightly but I had one of mine done by a well known independent and they didn't bother. Maybe put the new bearing in the freezer and take to garage in a cool box?

You will need a decent hex key to get the brake calipers undone, and two sorts of special gunk to reassemble so worth finding and reading some instructions first. Oh, and getting the brake shield off can be challenging too, as the little bolt will probably be siezed.

Don't let this put you off, it is DIYable just RTFM and allow time for snags.

AdrianR

jamiebae

Original Poster:

6,245 posts

242 months

Friday 6th July 2007
quotequote all
I'm going to see if they'll be covered under warranty first (1 year warranty from the Lotus dealer I bought it from) and otherwise I'll strip the hubs off and get the bearings changed over by a garage.

piooly

1,176 posts

256 months

Friday 6th July 2007
quotequote all
its not too bad a job, just take off the brake caliper and disk, use a very long ratchet wrench, as long as possible and take the center hub nut off. Then take the whole assembly to a local garage and get them to press the old one out with a press and fit the new one back in. They only charged me £5 to do that. Then just reassemble and your done. It is an easy job done that way, let them do the hard bit !

jamiebae

Original Poster:

6,245 posts

242 months

Friday 6th July 2007
quotequote all
piooly said:
its not too bad a job, just take off the brake caliper and disk, use a very long ratchet wrench, as long as possible and take the center hub nut off. Then take the whole assembly to a local garage and get them to press the old one out with a press and fit the new one back in. They only charged me £5 to do that. Then just reassemble and your done. It is an easy job done that way, let them do the hard bit !
So no need to split ball joints etc or did you gloss over that bit?

S Works

10,166 posts

281 months

Friday 6th July 2007
quotequote all
Bearings won't be covered by warranty - wear and tear part I'm afraid. As above, get it to a local garage you trust to take the old one out and fit the new one.

jamiebae

Original Poster:

6,245 posts

242 months

Friday 6th July 2007
quotequote all
S Works said:
Bearings won't be covered by warranty - wear and tear part I'm afraid. As above, get it to a local garage you trust to take the old one out and fit the new one.
I'm not expecting the warranty to cover the bearings but some do (depends on the level of cover). If the warranty doesn't cover it I'll strip the hubs down and fit the new bearings using the press at work.

piooly

1,176 posts

256 months

Friday 6th July 2007
quotequote all
jamiebae said:
piooly said:
its not too bad a job, just take off the brake caliper and disk, use a very long ratchet wrench, as long as possible and take the center hub nut off. Then take the whole assembly to a local garage and get them to press the old one out with a press and fit the new one back in. They only charged me £5 to do that. Then just reassemble and your done. It is an easy job done that way, let them do the hard bit !
So no need to split ball joints etc or did you gloss over that bit?
No you done need to split the ball joints, just unbolt the plate the ball joint bolts into. It will make sense when you look at it.

jamiebae

Original Poster:

6,245 posts

242 months

Friday 6th July 2007
quotequote all
piooly said:
jamiebae said:
piooly said:
its not too bad a job, just take off the brake caliper and disk, use a very long ratchet wrench, as long as possible and take the center hub nut off. Then take the whole assembly to a local garage and get them to press the old one out with a press and fit the new one back in. They only charged me £5 to do that. Then just reassemble and your done. It is an easy job done that way, let them do the hard bit !
So no need to split ball joints etc or did you gloss over that bit?
No you done need to split the ball joints, just unbolt the plate the ball joint bolts into. It will make sense when you look at it.
Cool, I'll call the dealer tomorrow and if they don't want to help (.....I'll be a bit cross, both bearings are shot and I only bought it 4 months ago from a Lotus dealer....) I'll get to work over the weekend, maybe!

jamiebae

Original Poster:

6,245 posts

242 months

Monday 9th July 2007
quotequote all
Busy weekend so only got round to calling the dealer today who were more than happy to help, wheel bearings will absolutely be covered under the warranty and the car is booked in next week for them to be sorted (the service manager seemed to think it was the bearings on both sides from my description of the symptoms) along with the MoT.

I'm a happy customer so well done to Dream Machines Lotus in Heathfield, Sussex smile

TheYeti

656 posts

247 months

Monday 9th July 2007
quotequote all
jamiebae said:
Busy weekend so only got round to calling the dealer today who were more than happy to help, wheel bearings will absolutely be covered under the warranty and the car is booked in next week for them to be sorted (the service manager seemed to think it was the bearings on both sides from my description of the symptoms) along with the MoT.

I'm a happy customer so well done to Dream Machines Lotus in Heathfield, Sussex smile
Nice one! Saves you the hassle.......and it IS a hassle...........