Please help before I screw up my car !
Please help before I screw up my car !
Author
Discussion

fatboy111

Original Poster:

308 posts

248 months

Tuesday 24th July 2007
quotequote all
This is going to sound easy...but.

I need to get the front Lotus badge off and re-apply properly (i.e. not 'on the wonk'). I've tried a few things like dental floss at first, then building up to a flat blade screw driver. This is where I stoppped as I could just see what was going to happen: SCRAAAAAAAAAAAPE all the way up to the windscreen!

I've tried a few of these when the car had been in the sun for a while and the body was hot; is it a hair dryer job?

Cheers in advance thumbup

TonyHetherington

32,091 posts

281 months

Tuesday 24th July 2007
quotequote all
I've not done it myself but the advice I've seen before (and been told it works) is heat it up with a hair dryer to get the glue soft and then use fishing line to run through it.

(mine's a bit wonky too, actually)

21TonyK

13,398 posts

240 months

Tuesday 24th July 2007
quotequote all
I believe that the front badge has a couple of locating pins that go through the clam so I don't think its that simple. My front was resprayed recently and I can see a couple of nicks in the front badge where they removed it and this was done by someone who is a renowned Lotus specialist so it can't be easy!

I'd hang on until someone who's "been there done that" comes a along.

ROB1979

221 posts

236 months

Tuesday 24th July 2007
quotequote all
I thought that only the S2 badge was stuck on, the S1 had 2 x M4/M5 nuts bolting it down from the underside of the front clam!

Please correct me if i'm wrong.

TonyHetherington

32,091 posts

281 months

Tuesday 24th July 2007
quotequote all
Are those the pins you can get to if you take the service panel off, or if you take the front grill out? (Which by the way is mega mega easy)

fatboy111

Original Poster:

308 posts

248 months

Tuesday 24th July 2007
quotequote all
I have an S1 BTW!

Those screws might have something to so with it!! Can anyone confirm this?

shangani

3,069 posts

268 months

Tuesday 24th July 2007
quotequote all
The badge is screwed on on an S1, stuck on on an S2. S1 has two bolts that go through the clam and they are very hard to access without removing the clam afaik.

TonyHetherington

32,091 posts

281 months

Tuesday 24th July 2007
quotequote all
ahhh, I have an S2. I didn't realise there was a difference. Sorry for confusion!

So if the S1 is bolted on, it doesn't leave much room for moving it then does it? Or is it just enough to make a difference?

fatboy111

Original Poster:

308 posts

248 months

Tuesday 24th July 2007
quotequote all
Wow, good job I decided to ask rather than give it some in an angry screwdriver wielding moment tonight! Cheers.

Edited by fatboy111 on Tuesday 24th July 10:28

S Works

10,166 posts

281 months

Tuesday 24th July 2007
quotequote all
shangani said:
The badge is screwed on on an S1, stuck on on an S2. S1 has two bolts that go through the clam and they are very hard to access without removing the clam afaik.
It's bolted on actually. To remove/refit is a clam off job.

fleetelise

2,430 posts

243 months

Tuesday 24th July 2007
quotequote all
I can just see a post now:

"I'm having the front clam off my car so I can change the badge, are there any other things I should have looke at at the same time?"
laugh

Cuzza

2,042 posts

284 months

Tuesday 24th July 2007
quotequote all
Can't you get at it with front grille out or is the crash structure in the way? ISTR it's not a clam off job to get the grille out.

Andy T

468 posts

259 months

Tuesday 24th July 2007
quotequote all
fatboy111 said:
This is going to sound easy...but.

I need to get the front Lotus badge off and re-apply properly (i.e. not 'on the wonk'). I've tried a few things like dental floss at first, then building up to a flat blade screw driver. This is where I stoppped as I could just see what was going to happen: SCRAAAAAAAAAAAPE all the way up to the windscreen!

I've tried a few of these when the car had been in the sun for a while and the body was hot; is it a hair dryer job?

Cheers in advance thumbup
What do you wanna take your badge off for anyway Fats?

A

S Works

10,166 posts

281 months

Tuesday 24th July 2007
quotequote all
You could dremel a hole in the clam I suppose, take it off and then re-bond it, flat it all back, repaint etc. Or then again...

21TonyK

13,398 posts

240 months

Tuesday 24th July 2007
quotequote all
S Works said:
You could dremel a hole in the clam I suppose, take it off and then re-bond it, flat it all back, repaint etc. Or then again...
What's wrong with that? Stranger things happen... whistle

GKP

15,099 posts

272 months

Tuesday 24th July 2007
quotequote all
Dremel the badge not the clam.

Paul RN

1,168 posts

245 months

Tuesday 24th July 2007
quotequote all
GKP said:
Dremel the badge not the clam.
  • ding* best way to remove it without taking the clam off. You can replace it with a cheaper S2 plastic badge and stick it on rather than the costly S1 (£50?) enamel badge.