Discussion
Apologies if I am in the wrong section.
Looking to buy my wife a Christmas present. Good deal? Any other suggestions
http://www.chisholmhunter.co.uk/18ct-white-gold-0-...
Looking to buy my wife a Christmas present. Good deal? Any other suggestions
http://www.chisholmhunter.co.uk/18ct-white-gold-0-...
Unless its a dress ring / occasional ring i wouldnt bother. This sort of ring wont last long and are often plagued with problems.
This is what we'd class as a 'recession ring' and are generally very light weight and cast with hollow shoulders to reduce metal material content whilst maintaining the heavier appearance. The problem with this is that they flex easily and as a result the stones are very prone to popping out.
Stones: The centre 6 stones will be matched laser cuts which interlock to give a flush fitting. The problem is if you do lose one (likely if the ring is worn a lot) its incredibly hard to get a replacement as they are serialised and every supplier and batch has different cutting specs. To get one means sending a couple of the remaining stones away to have a suitable stone cut or the serial numbers (sometimes laser etched on the girdle of the diamond) read to find other stones from the same batch or supplier. This, if at all possible can take a long time. The most common solution is to set a princess cut diamond of the same size and secure it by way of adding claws or pressing grains (slivers of the setting) over the edge of the stone to secure. Some jewellers have even been known to superglue a stone in as its very hard to get another stone to fit, but as you can imagine this has only a short term effect. The surrounding stones are less of an issue as they are grain set but i do see a good number coming in to have stones reset due to the ring flexing.
The shanks are generally quite thin and dont last particularly if worn all the time. Thin shanks also mean flex occurs and more importantly stones can become insecure.
As i said, if its to be an occasional dress ring she wont be fussed about wearing little then thats cool. However, if its something meaningful and long term then look elsewhere. Id always suggest having one hand made as it ensures you get solid materials and if there are any issues you can visit the supplier / goldsmith and have it rectified properly, rather than the retailer just sending away for a replacement, equally poor quality item. Sure it might cost more in the short term but it'll last you so much longer with far fewer issues.
As a repairer, designer and manufacturer i say the above with honesty and with no intention of skuppering the suppliers sale. You want advice, you got it!
Eddie
This is what we'd class as a 'recession ring' and are generally very light weight and cast with hollow shoulders to reduce metal material content whilst maintaining the heavier appearance. The problem with this is that they flex easily and as a result the stones are very prone to popping out.
Stones: The centre 6 stones will be matched laser cuts which interlock to give a flush fitting. The problem is if you do lose one (likely if the ring is worn a lot) its incredibly hard to get a replacement as they are serialised and every supplier and batch has different cutting specs. To get one means sending a couple of the remaining stones away to have a suitable stone cut or the serial numbers (sometimes laser etched on the girdle of the diamond) read to find other stones from the same batch or supplier. This, if at all possible can take a long time. The most common solution is to set a princess cut diamond of the same size and secure it by way of adding claws or pressing grains (slivers of the setting) over the edge of the stone to secure. Some jewellers have even been known to superglue a stone in as its very hard to get another stone to fit, but as you can imagine this has only a short term effect. The surrounding stones are less of an issue as they are grain set but i do see a good number coming in to have stones reset due to the ring flexing.
The shanks are generally quite thin and dont last particularly if worn all the time. Thin shanks also mean flex occurs and more importantly stones can become insecure.
As i said, if its to be an occasional dress ring she wont be fussed about wearing little then thats cool. However, if its something meaningful and long term then look elsewhere. Id always suggest having one hand made as it ensures you get solid materials and if there are any issues you can visit the supplier / goldsmith and have it rectified properly, rather than the retailer just sending away for a replacement, equally poor quality item. Sure it might cost more in the short term but it'll last you so much longer with far fewer issues.
As a repairer, designer and manufacturer i say the above with honesty and with no intention of skuppering the suppliers sale. You want advice, you got it!

Eddie
Gassing Station | Watches | Top of Page | What's New | My Stuff


