Removing Links / Adjusting Bracelet
Removing Links / Adjusting Bracelet
Author
Discussion

_Nathan_

Original Poster:

506 posts

279 months

Monday 26th November 2012
quotequote all
Hello,

I am having difficulty sizing the strap on a metal bracelet.

I need to remove two links, but in doing so I am facing difficulty removing a screw - it just spins around in both directions without any resistance.

Any suggestions greatly appreciated !


AndrewWF

280 posts

173 months

Monday 26th November 2012
quotequote all
Depending on the watch, it is quite possible that the links are secured with a threaded tube that requires fixing at one end and turning at the other to unscrew.

_Nathan_

Original Poster:

506 posts

279 months

Monday 26th November 2012
quotequote all
Not in this situation, the other side of the link is completely molded.

Googling about, there are other people who solved the problem by inserting a flat head screw driver inbetween the link and smashing it with a hammer !

You could't fit the smallest of screwdrivers in there.

AndrewWF

280 posts

173 months

Monday 26th November 2012
quotequote all
_Nathan_ said:
Not in this situation, the other side of the link is completely molded.

Googling about, there are other people who solved the problem by inserting a flat head screw driver inbetween the link and smashing it with a hammer !

You could't fit the smallest of screwdrivers in there.
That sounds a bit drastic! If the screw is spinning then it suggests that the thread itself may be stripped, but perhaps a slight bend is preventing the screw from coming free. Sounds like there is going to be some sacrifice required on the bracelet's part whatever happens...

Arrive Alive

282 posts

202 months

Monday 26th November 2012
quotequote all
What make is the bracelet? Any pictures?

_Nathan_

Original Poster:

506 posts

279 months

Monday 26th November 2012
quotequote all
its basically very similar to a Rolex sub. Flat screwdriver head on one side of the link.

Will post images when I get back home.

Spice_Weasel

2,369 posts

284 months

Monday 26th November 2012
quotequote all
There will be a knack to this unless there is some damage to the screw pin.

I doubt it will involve a hammer though!

Show us some pics as I am sure one of us will have experienced similar..

_Nathan_

Original Poster:

506 posts

279 months

Monday 26th November 2012
quotequote all


_Nathan_

Original Poster:

506 posts

279 months

Monday 26th November 2012
quotequote all



_Nathan_

Original Poster:

506 posts

279 months

Monday 26th November 2012
quotequote all
I have already tried that.

The faulty screw is in the link closest to the clasp in the second photo.

Argh !


clockworks

7,818 posts

176 months

Tuesday 27th November 2012
quotequote all
If it's Chinese fake Sub-type bracelet, it might be easier to buy another one on eBay, and swap the whole thing.
If the screw is turning both ways, but the head is in the fully-screwed-in position, then the thread is damaged. Quite possibly came out of the factory like that. If it's the link that's riveted to the clasp, there's not much you can do. Even if you cut it off with a hacksaw, you won't be able to put it back together, as the thread in the link is probably damaged, as well as the thread on the screw.

_Nathan_

Original Poster:

506 posts

279 months

Tuesday 27th November 2012
quotequote all
that is what I suspected.

Thakyou for your input

hilly10

7,543 posts

259 months

Tuesday 27th November 2012
quotequote all
Right thats it smash it with the hammer

CardShark

4,264 posts

210 months

Tuesday 27th November 2012
quotequote all
clockworks said:
If it's Chinese fake Sub-type bracelet....
Looking at the bracelet style, the case back and the shape of the case itself I'd guess at it being more than a fake bracelet.

clockworks

7,818 posts

176 months

Wednesday 28th November 2012
quotequote all
CardShark said:
Looking at the bracelet style, the case back and the shape of the case itself I'd guess at it being more than a fake bracelet.
It could be an homage - Steinhart (although the bracelet quality would be a lot better), Alpha, Invicta, etc. - or even a self-build.
Might even be a real Sub with a Chinese bracelet.

I've got a fake bracelet on my Sub. I needed to remove an extra (riveted) link from the bracelet of my 14060, as i have small wrists, and the clasp wouldn't sit centrally on the back of my wrist.
Rather than butcher the original, I bought a fake (with no logo) on eBay. Hacksawed off one of the fixed links, and fitted the original Rolex clasp. So, it's a genuine watch and clasp, with fake links.

You are probably right, though!

NDA

25,836 posts

256 months

Wednesday 28th November 2012
quotequote all
It's not a screw - its a split pin.

You're looking at the end of the split pin (which looks like flat head screw).

They're very hard to get out, you'll need the wee tool you can find on Amazon - its like a mini vice that screws a small pin on top of the split pin and forces it out. Not expensive to buy and useful for the next strap. smile


Actually - edit. Looking more closely at your pics, it does look more like a screw!!

clockworks

7,818 posts

176 months

Wednesday 28th November 2012
quotequote all
NDA said:
It's not a screw - its a split pin.

You're looking at the end of the split pin (which looks like flat head screw).

They're very hard to get out, you'll need the wee tool you can find on Amazon - its like a mini vice that screws a small pin on top of the split pin and forces it out. Not expensive to buy and useful for the next strap. smile
That was my first thought.
However, the OP says that the other side of the link is "completely moulded", which I take to mean that it's a blind hole. If it was a split pin, there would be a hole on both sides of the link to allow the pin to be pushed out.