Washing machine fault
Discussion
1. Is the mains outlet to the washing machine capable of carrying 15 amps? Most washing machines are ‘rated’ at 5 amps but can draw 15 amps when starting up.
2. Unplug other electrical appliances – does the RCD still trip? Is the supply socket hot? Could be a loose wire in the electrical socket.
3. Is the drum stiff to turn? A stiff drum can draw too much current and trip an RCD – take the back off the washing machine and see if anything is jammed near the drum.
4. Has there been a water leak recently? Water can short electrical circuit – leave a couple of days and try again.
5. Is there a lot of black dust about? A worn motor can give off carbon particles. You will need to change the washing machine motor.
6. Is the door stiff to open? A stiff door lock mechanism can draw too much current during the wash cycle and trip an RCD. Investigate the door locking mechanism – try some oil or WD40.
7. Is the washing machine far enough away from the wall? Lack of ventilation can cause condensation – condensation can short an electrical circuit and cause the RCD to trip.
8. Does the washing machine sound the same as before? A different noise suggest something is wrong with the washing machine.
9. Check the cable, is the power cable damaged? Repair or replace if necessary.
10. Plug the machine into another socket. If the RCD does not trip the problem is the wall socket or associated circuit.
11. Does theRCD trip at the start of the washing cycle? If yes, likely to be the washing machine pump.
12. Find out what part of the washing cycle the RCD trips. Always the same part of the cycle? What is the washing machine doing? Heating water? Draining water? Spin.
2. Unplug other electrical appliances – does the RCD still trip? Is the supply socket hot? Could be a loose wire in the electrical socket.
3. Is the drum stiff to turn? A stiff drum can draw too much current and trip an RCD – take the back off the washing machine and see if anything is jammed near the drum.
4. Has there been a water leak recently? Water can short electrical circuit – leave a couple of days and try again.
5. Is there a lot of black dust about? A worn motor can give off carbon particles. You will need to change the washing machine motor.
6. Is the door stiff to open? A stiff door lock mechanism can draw too much current during the wash cycle and trip an RCD. Investigate the door locking mechanism – try some oil or WD40.
7. Is the washing machine far enough away from the wall? Lack of ventilation can cause condensation – condensation can short an electrical circuit and cause the RCD to trip.
8. Does the washing machine sound the same as before? A different noise suggest something is wrong with the washing machine.
9. Check the cable, is the power cable damaged? Repair or replace if necessary.
10. Plug the machine into another socket. If the RCD does not trip the problem is the wall socket or associated circuit.
11. Does theRCD trip at the start of the washing cycle? If yes, likely to be the washing machine pump.
12. Find out what part of the washing cycle the RCD trips. Always the same part of the cycle? What is the washing machine doing? Heating water? Draining water? Spin.
oilslick said:
You know this is a car forum? 
2 posts, all washing machine related.
Pistonheads? I don't get it. Gassing station? Could, if we were talking cookers. What next?
Anyway heating element very possible, OP could try a cold wash and see whether that makes any difference. Having just taken a washing machine apart to make it lighter for disposal purposes, and also because I was curious as to what nearly made the outer drum explode (a broken "cross") I can only say that the heating element is very very hard to get to so the OP, if not a very DIY type, may have to reconsider repairing if this is the case.
Vacumatic said:
Anyone remember when you got a Thank You for Helping others?
Just a somewhat typical example of the lock of courtesy on this site these days sir and certainly no consideration for your comprehensive and informative post.I know I am old but really have all the elements of basic civility been lost in the electronic age?
medieval said:
Vacumatic said:
Anyone remember when you got a Thank You for Helping others?
Just a somewhat typical example of the lock of courtesy on this site these days sir and certainly no consideration for your comprehensive and informative post.I know I am old but really have all the elements of basic civility been lost in the electronic age?
Vacumatic said:
1. Is the mains outlet to the washing machine capable of carrying 15 amps? Most washing machines are ‘rated’ at 5 amps but can draw 15 amps when starting up.
Since most washing machines have at least a 2kW heater, I'm not sure where the 5 amp rating comes from. A UK mains plug has a maximum fuse rating of 13 Amps, so a machine sold for use within the UK should not be consuming more than this.you don't mention if it's the RCD or MCB that's tripping. RCD would indicate an earth fault( heating element is likely culprit),MCB =excess draw of power - could be anything which is switched on when it trips.
Then again ,it's an electrical fault- if you have to ask, (with all due respect) , are you competent to work on MAINS electricity. If not- D & G ( http://www.domgen.com/ --PHONE 0800 597 8600 ) offer a reasonable repair scheme with extended cover for a small monthly fee.
Have a ask on this site - http://www.ukwhitegoods.co.uk/forumsphpbb3/
You WILL have to register and give the Make/Model name or number to get help.
Mike- I have a Zanussi oven unit which ( from calculation ) borders on 16 A ,but is supplied to be wired, with no warning NOT to use a 13a socket.
Then again ,it's an electrical fault- if you have to ask, (with all due respect) , are you competent to work on MAINS electricity. If not- D & G ( http://www.domgen.com/ --PHONE 0800 597 8600 ) offer a reasonable repair scheme with extended cover for a small monthly fee.
Have a ask on this site - http://www.ukwhitegoods.co.uk/forumsphpbb3/
You WILL have to register and give the Make/Model name or number to get help.
Mike- I have a Zanussi oven unit which ( from calculation ) borders on 16 A ,but is supplied to be wired, with no warning NOT to use a 13a socket.
Edited by Who me ? on Friday 3rd April 20:13
Gassing Station | Homes, Gardens and DIY | Top of Page | What's New | My Stuff




