Dishwasher circulation pump - repair or replace
Discussion
Hi all
We’ve got a 9 year old Zanussi dishwasher. It has started making a high pitched squeal during the cycle. More recently it has stopped switching off at the end of the cycle ie displaying the end light.
Armchair research indicates this is probably the circulation pump because the sump is clean and empty. It doesn’t seem to happen during the water fill steps and the noise lasts too long to be clean water flow.
My query is whether to spend £80 and a couple of hours replacing the circulation motor or replace the unit given its age. I much prefer repairing items than throwing them away but common sense may suggest modern appliances have a modest service life.
Ideas welcome.
We’ve got a 9 year old Zanussi dishwasher. It has started making a high pitched squeal during the cycle. More recently it has stopped switching off at the end of the cycle ie displaying the end light.
Armchair research indicates this is probably the circulation pump because the sump is clean and empty. It doesn’t seem to happen during the water fill steps and the noise lasts too long to be clean water flow.
My query is whether to spend £80 and a couple of hours replacing the circulation motor or replace the unit given its age. I much prefer repairing items than throwing them away but common sense may suggest modern appliances have a modest service life.
Ideas welcome.
I'm always inclined to fix things if I can and I'd certainly have a go replacing the circulation pump, but its price is a fair percentage of a whole new dishwasher, so I can see why you're wondering about it.
I personally wouldn't be too worried about the service life of the rest of the machine. The circulation pump is the most likely component of value to wear out, so replacing it should give the machine a substantial new lease of life. The drain pump might fail at some point too, but it is a much cheaper (and usually even simpler) component to replace.
I personally wouldn't be too worried about the service life of the rest of the machine. The circulation pump is the most likely component of value to wear out, so replacing it should give the machine a substantial new lease of life. The drain pump might fail at some point too, but it is a much cheaper (and usually even simpler) component to replace.
I can get a new circulation pump for £67. A new midrange machine is about £450. I’m leaning towards a repair attempt. I changed the heater a few years ago but otherwise it’s been reliable. The drain pump runs for a more shorter time but I guess it’s also a much less robust motor.
All replies appreciated - thank you.
All replies appreciated - thank you.
Mine made an awful whining noise and stopped cleaning as much as it should - the pump had somehow sucked in the foil cap from a milk bottle.
Machine tipped over, suction side pulled off, offending foil removed, machine worked well - until the next foil cap. Repeat, and works again!
How the foil got into the machine and past the filters I do not know. Total cost was a bit of silicone as I couldn't get the pump to seal up afterwards.
Do not get me started on how long it takes to get seeds out of the spinning arms.
Machine tipped over, suction side pulled off, offending foil removed, machine worked well - until the next foil cap. Repeat, and works again!
How the foil got into the machine and past the filters I do not know. Total cost was a bit of silicone as I couldn't get the pump to seal up afterwards.
Do not get me started on how long it takes to get seeds out of the spinning arms.
Peanut Gallery said:
Do not get me started on how long it takes to get seeds out of the spinning arms.
And bits of chopped garlic.It'd be nice if you could disassemble the arms to remove the decomposing crap that can accumulate in them. Lugs to locate the arm and then a screw cap to hold it in place, perhaps. But it's all extra complexity and cost.
I've replaced the pump on 2 dishwashers, last time a couple of months ago. They were Bosch so the circulation pump and heater are all in one making them a little expensive (I think about £80).
Its no more than an hour to do, less I reckon and dead easy. Saves a lot of money over a new machine.
I've just done the drain pump on our Bosch washing machine - £50 and about an hour again.
Its no more than an hour to do, less I reckon and dead easy. Saves a lot of money over a new machine.
I've just done the drain pump on our Bosch washing machine - £50 and about an hour again.
Simon_GH said:
Hi all
We ve got a 9 year old Zanussi dishwasher. It has started making a high pitched squeal during the cycle. More recently it has stopped switching off at the end of the cycle ie displaying the end light.
Earlier this year my (then) 7 year old Zanussi integrated dishwasher just stopped working. The fused connection point is behind it, inaccessible and this was three days before completion of the sale of the house. I went to the local family owned small town electrical appliances shop (place looked like it was still the 1960's). Told them the problem... "Oh do you live on the **** estate?" Yes I do as a matter of fact, how do you know?We ve got a 9 year old Zanussi dishwasher. It has started making a high pitched squeal during the cycle. More recently it has stopped switching off at the end of the cycle ie displaying the end light.
"We have probably replaced most of those Zanussi dishwashers now, dozens of them - with Beko units!"
They fitted a new Beko for me the following week .
Gassing Station | Homes, Gardens and DIY | Top of Page | What's New | My Stuff


