Maths/geometry/physics question
Maths/geometry/physics question
Author
Discussion

227bhp

Original Poster:

10,203 posts

159 months

Saturday 30th May 2015
quotequote all
Sorry for the long explanation, but the only way I can put the question across is like this:

I'm putting a digital 'bike computer' on my push bike, basically it displays road speed, mileage and other stuff. It does this by means of a sensor/sender unit mounted on the front fork and a magnet fitted to a spoke, the magnet does one revolution, passes the mag sensor which registers it, sends a signal up the wire to the computer bit which converts it to miles/speed/whatever else.
You have to tell the computer what the circumference of the wheel/tyre is ie: One revolution = 2300mm.

Are you wit' me? wink

So all well and good, but here's the question; does it matter where on the spoke I mount the magnet? If I mount it closer to hub or more towards the rim? Does one revolution of the wheel change what the sensor reads dependent on where it is mounted?
This I cannot get my head around! banghead
I think I'm ok to mount it anywhere up and down the spoke, but need to be sure. If not the whole thing is pointless.
The question arose as the instructions just say 'Mount the sensor halfway up the fork', but makes no point of measuring it or saying it is important. I can't mount it very easily halfway as the spokes are far from parallel with the forks so the thing is fitted quite near the hub (the gap between mag and sensor needs to be 2mm).
Thanks for reading smile

john2443

6,553 posts

242 months

Saturday 30th May 2015
quotequote all
Doesn't matter how far up the spoke you put it as long as the 2 parts are close enough for one to know that the other has gone past.

It's measuring revolutions and a rev is a rev whether the magnet has done a long or short distance it's still a rev.

MKnight702

3,440 posts

245 months

Saturday 30th May 2015
quotequote all
No it does not matter. All the sensor does is count the number of revolutions in a given time period. You have already told the computer what the circumference of the wheel is, so the sensor gives the frequency these revolutions happen.

98elise

32,890 posts

192 months

Saturday 30th May 2015
quotequote all
Echo the above, wherever it is on the spoke it would pass the sensor at the same point in time. At that point the wheel has turned one rev, and the bike has therefore moved forward whatever the circumference of the tyre is.

227bhp

Original Poster:

10,203 posts

159 months

Saturday 30th May 2015
quotequote all
I got it, thanks for the explanations and setting my mind at rest. I was thinking it wouldn't matter, but then the brain drifted onto distance and speed of rim and hub and got sidetracked....
I'm going for a ride byebye

crossy67

1,570 posts

210 months

Saturday 30th May 2015
quotequote all
Don't listen to these idiots, the closer to the hum the smaller the circumference. Because it's so much smaller it has to turn faster to keep up with the outside of the wheel.

Only kidding tongue out I would put it further away from the hub so it passes the sensor faster. Also measure the rolling radius with you sitting on the bike. Don't know why but it made a difference on ours.

ian in lancs

3,853 posts

229 months

Saturday 30th May 2015
quotequote all
It doesn't matter where on the spoke. As others have said its measuring the frequency of a single rotation (f). You set the circumference on the computer (c). All the computer is doing is displaying f x c = speed and distance. Anyway, I use a running watch from decathlon. £50 gives a GPS watch that tracks distance, speed etc etc, mega accurate and flexibly for loads of sports.

Troubleatmill

10,210 posts

190 months

Saturday 30th May 2015
quotequote all
For this to work effectively- you need to get an oval wheel.

Good bike shops keep them in back.

mko9

2,994 posts

243 months

Saturday 30th May 2015
quotequote all
Also, the plane takes off. wink

TwigtheWonderkid

49,280 posts

181 months

Saturday 30th May 2015
quotequote all
crossy67 said:
Also measure the rolling radius with you sitting on the bike. Don't know why but it made a difference on ours.
Should be fine if you measure from the centre of the wheel to the top of the tyre, double it and multiply by Pi.

JM

3,170 posts

237 months

Saturday 30th May 2015
quotequote all
crossy67 said:
Also measure the rolling radius with you sitting on the bike. Don't know why but it made a difference on ours.
Put more air in your tyres.


crossy67

1,570 posts

210 months

Saturday 30th May 2015
quotequote all
I am a bit anal about things like this and followed the programing steps to the letter and there is a difference between unloaded and loaded. My road bike tyres are kept at 90psi, I can't get them any harder.

timbo999

1,551 posts

286 months

Saturday 30th May 2015
quotequote all
Just download mapmyride...getmecoat

driverrob

4,847 posts

234 months

Saturday 30th May 2015
quotequote all
The position could make a difference: not in terms of accuracy but in terms of working or not. The sensor will need to sense the magnet for a minimum length of time for it to register. Nearer the rim the magnet is moving faster and thus spends a shorter time going past the sensor.
If the sensor does not respond very quickly you might find that, above a certain road speed, it starts giving a lower speed reading. If so, move it all closer to the hub. But this is pretty unlikely.

anonymous-user

85 months

Saturday 30th May 2015
quotequote all
crossy67 said:
I am a bit anal about things like this and followed the programing steps to the letter and there is a difference between unloaded and loaded. My road bike tyres are kept at 90psi, I can't get them any harder.
If you want to pump them up a bit more, get a better pump. Pretty much any decent track pump could get them to 150 psi if you really want to.

crossy67

1,570 posts

210 months

Saturday 30th May 2015
quotequote all
The tyres only said to inflate to 90psi max