Discussion
Simply do a search on here for "Max Power".
I think you'll find that the following helps
leave foglights on
blue neon washer jets
bodykit
undercar lighting
tape up unused areas of windscreen
large exhaust and or trim
different wheels
decals
turn baseball cap around
any ICE over 500watts
colour of car
Andy
I think you'll find that the following helps
leave foglights on
blue neon washer jets
bodykit
undercar lighting
tape up unused areas of windscreen
large exhaust and or trim
different wheels
decals
turn baseball cap around
any ICE over 500watts
colour of car
Andy

You can fit a larger K series engine. I found a tuned 1.8 Metro to be very entertaining.
If you are serious about upgrading the Metro have a look at the Moto-Build Racing Website or give them a ring and chat to Darryl Davies, he is a keen racer and all round nice guy, I have dealt will them and can thoroughly recommend them for all things Rover from Max Power through to a full race Elise Conversions.
You have the basis of a great fun car in your Metro, don't let typical PH barbs put you off, we can't all afford to run junior supercars.
If you are serious about upgrading the Metro have a look at the Moto-Build Racing Website or give them a ring and chat to Darryl Davies, he is a keen racer and all round nice guy, I have dealt will them and can thoroughly recommend them for all things Rover from Max Power through to a full race Elise Conversions.
You have the basis of a great fun car in your Metro, don't let typical PH barbs put you off, we can't all afford to run junior supercars.
andyf007 said: On a serious note, will the Mk1 MG Metro Turbo engine fit? That was a scarey little car in it's day.
Andy
It could be made to fit with difficulty but it would not be as good as the K series fitted. If you really want to go bonkers and make life hard you can fit a Honda VTEC or even a 16V 2 Litre Vauxhall but K series transplants are easiest to do.
Hi girls, where do i get all this stuff from?
Damo
Damo
planetdave said: Dependson how much wonga you chuck at it.
It is normal to start with the breathing (k&n, that sort of thing), a better exhaust,High pressure fuel pump, good sparks, chip, all the way up to bigger valves or forced induction
Damo, I doubt its sensible to even bother. You'll get reasonably negligable improvements, and its going to cost more than your car is worth.
Elises+Caterhams etc. all have k series engines so there is a lot of stuff out there, but its going to a couple of k to get anything even vaguely noticeable.
You'd be better of putting that money to a better car imho. Even if you up the engine power, you've got an expensive problem with shit suspension, tyres and brakes.
Easy
Strip it right down and cut out the floor pan. take the remains of the shell to a chap i know and he 'll weld in a 6r4 cage. find either a 6r4 motor or a V8 and bolt to 6r4 mechanicals.
Sorted you will then have on damb quick metro....
cost is about 25-30k ish depending on spec...
Im still looking for an original one though..
Then i can tell everyone i drive a metro
and ask them for a race
Strip it right down and cut out the floor pan. take the remains of the shell to a chap i know and he 'll weld in a 6r4 cage. find either a 6r4 motor or a V8 and bolt to 6r4 mechanicals.
Sorted you will then have on damb quick metro....
cost is about 25-30k ish depending on spec...
Im still looking for an original one though..
Then i can tell everyone i drive a metro
and ask them for a raceI used to run an early A series Metro .. wonderful car.
Don't know if you read a recent cars and car conversions? .. metro was budget track car of the year! .. fab piccie of it overtaking a scoobie, and that's in std form.
I say go for it .. how quickly people laugh here when it fact you have the basis for a really fun and cheap rocket.
recently at donington there was a VERY fast metro with a 1.8VVC engine .. a little too quick at one point when the throttle stuck though..
If you've the got single point injection version there's not a gret deal you can do, going to throttle bdies and an emerald ECU would give useful urge and better driveability though. the multi point injection engine is much better in the first place, and good filter and exhaust (magnex do a belter) is the place to start.
early metros came with 4 pot calipers (mine did and that was a 1.0L to begin with!!) .. assuming the hubs are similar you could swap those over and get some grooved (not cross drilled ) discs.
saving weight is also a good move .. metros are blessed with a strong shell because of those very deep sills, but if your car is tired then seam welding might be sensible and reltively cheap if you have a MIG welder.
I would:
chuck out anything heavy .. underfelt / subwoofer (if you fitted one!) , get lightweight seats etc
Seam weld body
change exhaust and filter
substitute glass for perspex / polycarb
change front dampers
fit van rear hydro units (stiffer) and rear a/roll bar from early metro turbo
change front brakes
buy emerald and remap
good luck
Don't know if you read a recent cars and car conversions? .. metro was budget track car of the year! .. fab piccie of it overtaking a scoobie, and that's in std form.
I say go for it .. how quickly people laugh here when it fact you have the basis for a really fun and cheap rocket.
recently at donington there was a VERY fast metro with a 1.8VVC engine .. a little too quick at one point when the throttle stuck though..
If you've the got single point injection version there's not a gret deal you can do, going to throttle bdies and an emerald ECU would give useful urge and better driveability though. the multi point injection engine is much better in the first place, and good filter and exhaust (magnex do a belter) is the place to start.
early metros came with 4 pot calipers (mine did and that was a 1.0L to begin with!!) .. assuming the hubs are similar you could swap those over and get some grooved (not cross drilled ) discs.
saving weight is also a good move .. metros are blessed with a strong shell because of those very deep sills, but if your car is tired then seam welding might be sensible and reltively cheap if you have a MIG welder.
I would:
chuck out anything heavy .. underfelt / subwoofer (if you fitted one!) , get lightweight seats etc
Seam weld body
change exhaust and filter
substitute glass for perspex / polycarb
change front dampers
fit van rear hydro units (stiffer) and rear a/roll bar from early metro turbo
change front brakes
buy emerald and remap
good luck

Gassing Station | General Gassing [Archive] | Top of Page | What's New | My Stuff





