Steering goes CLUNK, engine goes WHINE...whats that mean?
Discussion
In all these years i've never really had to post a mechanical question...so hope General is the right forum!
Wifes Clio soon to be sold so need to fix to little issues...what are these likely to be:
Engine at tickover "whines"...a little revs and it stops, revs drop back to tick over and it whines again...bit like a squeaky...squeely..whine????
When reversing slowly on full lock (like daily to get out the drive way) theres a CLUNK from the front wheels....sometimes when opo lock is put on to then drive froward it does it again. "feels" like its from somewhere between the steering wheel and the front wheels! I realise there is a whole lot of stuff between those two points!
Any thoughts mechanical people!
Wifes Clio soon to be sold so need to fix to little issues...what are these likely to be:
Engine at tickover "whines"...a little revs and it stops, revs drop back to tick over and it whines again...bit like a squeaky...squeely..whine????
When reversing slowly on full lock (like daily to get out the drive way) theres a CLUNK from the front wheels....sometimes when opo lock is put on to then drive froward it does it again. "feels" like its from somewhere between the steering wheel and the front wheels! I realise there is a whole lot of stuff between those two points!
Any thoughts mechanical people!
As has been said the whine is likely to be the belts.
To diagnose carefully spray each belt in turn (not the cambelt though) with WD40 while you can hear the whining (or spray with water if you are worried about WD40 affecting the belts). If the whine goes that's the belt causing the problem. Check to make sure it's not worn, frayed, cracked etc. and replace if it is. If the belts OK it's probably just a bit loose. Tighten it so you can just about twist it 90Deg with thumb and finger on it's longest stretch (general rule, check manufacturer for proper tension).
Again as has been said 'clunks' from the front are likely to be worn or broken suspension components.
To diagnose which component get someone to rock the car back and forth while on full lock and while doing so reach under and feel each of the components in turn. Ball joints and bushes should have virtually no movement, likewise the top mounts should only have slight movement. Check the condition of the springs too.
A regular clunk on full lock can also be the CV joint. Check the condition of the driveshaft boots (no splits or grease escaped).
The above is a rough, non car specific guide.
To diagnose carefully spray each belt in turn (not the cambelt though) with WD40 while you can hear the whining (or spray with water if you are worried about WD40 affecting the belts). If the whine goes that's the belt causing the problem. Check to make sure it's not worn, frayed, cracked etc. and replace if it is. If the belts OK it's probably just a bit loose. Tighten it so you can just about twist it 90Deg with thumb and finger on it's longest stretch (general rule, check manufacturer for proper tension).
Again as has been said 'clunks' from the front are likely to be worn or broken suspension components.
To diagnose which component get someone to rock the car back and forth while on full lock and while doing so reach under and feel each of the components in turn. Ball joints and bushes should have virtually no movement, likewise the top mounts should only have slight movement. Check the condition of the springs too.
A regular clunk on full lock can also be the CV joint. Check the condition of the driveshaft boots (no splits or grease escaped).
The above is a rough, non car specific guide.
OK...after an hour of doing circles in my drive with my son sat on the engine feeling things we have discover......clunking top mount!
When on full lock then turning the wheel the otherway the top mount on the drivers side jolts and goes clunk!...so how do we fix that? could it be as simple as just tightening the big nut on top or can i "over" tighten that?
When on full lock then turning the wheel the otherway the top mount on the drivers side jolts and goes clunk!...so how do we fix that? could it be as simple as just tightening the big nut on top or can i "over" tighten that?
Gassing Station | General Gassing [Archive] | Top of Page | What's New | My Stuff






