What ever happened to blueprinted engines
What ever happened to blueprinted engines
Author
Discussion

Mr Green

Original Poster:

936 posts

213 months

Saturday 13th March 2010
quotequote all
Do people not bother doing this anymore?

EDLT

15,421 posts

237 months

Saturday 13th March 2010
quotequote all
I not sure if there is as much to gain on a modern engine, racers still do it though.

Boosted LS1

21,200 posts

291 months

Saturday 13th March 2010
quotequote all
Modern engines are often made to much better tolerences then those from days gone past. In effect the manufacturer does a lot of this already. That said, as soon as you change some internal parts you can blueprinting things yourself where appropriate. I do it all the time to varying degrees.

T350 Al

624 posts

222 months

Saturday 13th March 2010
quotequote all
I think STR8 Six or TVR Power still offer this for the Speed6? At the very least they did until very recently.

Daston

6,154 posts

234 months

Saturday 13th March 2010
quotequote all
T350 Al said:
I think STR8 Six or TVR Power still offer this for the Speed6? At the very least they did until very recently.
I would have thought if you were doing a full rebuild then you might as well go for a blueprinted setup no?

T350 Al

624 posts

222 months

Saturday 13th March 2010
quotequote all
Daston said:
T350 Al said:
I think STR8 Six or TVR Power still offer this for the Speed6? At the very least they did until very recently.
I would have thought if you were doing a full rebuild then you might as well go for a blueprinted setup no?
I agree. It was an option at one point, but I've no idea if it's been sucked up into a standard rebuild now though?

LukeBird

17,170 posts

240 months

Saturday 13th March 2010
quotequote all
The 360 Challenge Stradale had a blueprinted engine AFAIR.

BOR

5,154 posts

286 months

Saturday 13th March 2010
quotequote all
Where do you get the blueprints from, then ?

grumbledoak

32,571 posts

264 months

Saturday 13th March 2010
quotequote all
Boosted LS1 said:
Modern engines are often made to much better tolerences...
This, in a nutshell. No room for improvement. Well, not enough.

busta

4,504 posts

264 months

Saturday 13th March 2010
quotequote all
What exactly does blueprinting entail? I've seen it mentioned in mags and stuff, but never quite worked out exactly what it involves and what the benefits are.

the_engineer

335 posts

208 months

Saturday 13th March 2010
quotequote all
to shed some light on the above question, AFAIK, blueprinting an engine, involves matching an actual engine to its design specifications. Differences occur initially due to the previously mentioned tolerances involved in manufacturing and production. Thus you bring the engine closer to the original engineering specifications (where it should perform as the calculations at the design stage said it would).

Hope I've got that right? or someone please correct me smile

Boosted LS1

21,200 posts

291 months

Saturday 13th March 2010
quotequote all
^ Yas you're correct. Often in racing, rules stopped you making big improvements so you were limited to optimising the engine to it original spec ie the blueprint. Things like matching intake manifolds to the ports in the head and removing casting flash.

That said, you can go a lot further if there aren't any rules to worry about. Good example are piston rings. The gaps on stock engines are usually huge. Fitting 'file to fit' rings allows you to go to the tighter end of the scale. You can fit lighter pistons and pins, lighter conrods and balance everything properly. You can run the piston crowns closer to the head to improve squish. There are quite a lot of other things you can do to make a smoother running engine which will breath better.

Or, fit a turbo and be done with it smile