Removing car seats?
Author
Discussion

JudgeMental

Original Poster:

7,251 posts

261 months

Monday 1st October 2012
quotequote all
I'm looking to temporarily remove the driver's seat in my car and I can see it is attached to two rails bolted to the floor. I need these out of the way. Is it simply a matter of undoing the bolts to the carpet and lift the rails, or are there more intricate workings under there I should be aware of?

Condi

20,144 posts

199 months

Monday 1st October 2012
quotequote all
Bolts I think, probably with Torx heads?

G600

1,479 posts

215 months

Monday 1st October 2012
quotequote all
Assuming they aren't heated or fitted with airbags then yes they are just bolted down, nothing to worry about when removing them.

JudgeMental

Original Poster:

7,251 posts

261 months

Monday 1st October 2012
quotequote all
Thank you

ETA

I can see they are a funny star shape head

Does this neccesiate specialist tools, only if so the cost is likely to exceed the benefit of lifting them out frown



Edited by JudgeMental on Monday 1st October 18:59

s3fella

10,524 posts

215 months

Monday 1st October 2012
quotequote all
What car? Be careful removing seats, modernish cars have seats with airbags and pretensioners etc that'll blow your cock off if you get it wrong.

JudgeMental

Original Poster:

7,251 posts

261 months

Monday 1st October 2012
quotequote all
Boxster S

Pothole

34,367 posts

310 months

Monday 1st October 2012
quotequote all
JudgeMental said:
Thank you

ETA

I can see they are a funny star shape head

Does this neccesiate specialist tools, only if so the cost is likely to exceed the benefit of lifting them out frown



Edited by JudgeMental on Monday 1st October 18:59
^^ google torx.

davepoth

29,395 posts

227 months

Monday 1st October 2012
quotequote all
s3fella said:
What car? Be careful removing seats, modernish cars have seats with airbags and pretensioners etc that'll blow your cock off if you get it wrong.
Yup, disconnect the battery and leave for an hour or so just to be sure. The screws will have a Torx head, available from Maplins or similar; it might be a "security Torx" which has an extra pin in the top and needs a slightly different head, also available from Maplins.

s3fella

10,524 posts

215 months

Monday 1st October 2012
quotequote all
Don't worry, your car has already replaced your cock!! laugh



JudgeMental

Original Poster:

7,251 posts

261 months

Monday 1st October 2012
quotequote all
s3fella said:
Don't worry, your car has already replaced your cock!! laugh
hehe wife's car

Condi

20,144 posts

199 months

Monday 1st October 2012
quotequote all
s3fella said:
What car? Be careful removing seats, modernish cars have seats with airbags and pretensioners etc that'll blow your cock off if you get it wrong.
There should be a standard connector which you can unplug. Nothing is 'primed' or 'live' and shouldnt go off without the right inputs from the computer.

AndyLB

428 posts

192 months

Monday 1st October 2012
quotequote all
If in a hurry the right sized flat-head may oblige, wedged into two of the prongs of the torx star.

/bodge mode

JudgeMental

Original Poster:

7,251 posts

261 months

Monday 1st October 2012
quotequote all
Pothole said:
JudgeMental said:
Thank you

ETA

I can see they are a funny star shape head

Does this neccesiate specialist tools, only if so the cost is likely to exceed the benefit of lifting them out frown



Edited by JudgeMental on Monday 1st October 18:59
^^ google torx.
frown Cost more than any gain I would have had

Pothole

34,367 posts

310 months

Monday 1st October 2012
quotequote all
Condi said:
s3fella said:
What car? Be careful removing seats, modernish cars have seats with airbags and pretensioners etc that'll blow your cock off if you get it wrong.
There should be a standard connector which you can unplug. Nothing is 'primed' or 'live' and shouldnt go off without the right inputs from the computer.
but do you cut the blue or the red wire?

anonymous-user

82 months

Monday 1st October 2012
quotequote all
what is it for OP?

cleaning or..?

As mentioned, disconnect battery, and once unbolted, slowly lift them up to check for wires, an if there are any, unplug them.

JudgeMental

Original Poster:

7,251 posts

261 months

Monday 1st October 2012
quotequote all
duckhunt said:
what is it for OP?

cleaning or..?

As mentioned, disconnect battery, and once unbolted, slowly lift them up to check for wires, an if there are any, unplug them.
I can see two £1 coins (and a 20 or 50p) trapped under the rail, but no amount of fiddling with screwdrivers etc.will get them out.

Major Fallout

5,278 posts

259 months

Monday 1st October 2012
quotequote all
s3fella said:
What car? Be careful removing seats, modernish cars have seats with airbags and pretensioners etc that'll blow your cock off if you get it wrong.
laugh That really did make me laugh!

marksx

5,174 posts

218 months

Monday 1st October 2012
quotequote all
Make sure you disconnect the battery before unplugging any wires. I don't know about Porkers specifically, but some cars throw up an airbag fault which can only be cleared with fancy computer equipment (£ at the garage) if the wires are parted.

anonymous-user

82 months

Monday 1st October 2012
quotequote all
JudgeMental said:
duckhunt said:
what is it for OP?

cleaning or..?

As mentioned, disconnect battery, and once unbolted, slowly lift them up to check for wires, an if there are any, unplug them.
I can see two £1 coins (and a 20 or 50p) trapped under the rail, but no amount of fiddling with screwdrivers etc.will get them out.
That really made me laugh more.

Is this thread happening in Yorkshire?

JudgeMental

Original Poster:

7,251 posts

261 months

Monday 1st October 2012
quotequote all
marksx said:
Make sure you disconnect the battery before unplugging any wires. I don't know about Porkers specifically, but some cars throw up an airbag fault which can only be cleared with fancy computer equipment (£ at the garage) if the wires are parted.
Bugger frown