Lining a steel coolant header tank
Discussion
My (steel)coolant header tank has sprung a leak over the weekend, its quite corroded on the inside. I intend to weld up the 2 small leaks, but want a more permanent solution.
This is on my ferrari mondial, and ferrari want silly money for a new one, so i wont be going down that route, however i wont want to get a non-standard alloy one, as it would look rather out of place, and wont have a port for the level sender.
So i was thinking, you can get epoxy stuff for lining fuel tanks, can you get anything suitable for lining a coolant header tank?
This is on my ferrari mondial, and ferrari want silly money for a new one, so i wont be going down that route, however i wont want to get a non-standard alloy one, as it would look rather out of place, and wont have a port for the level sender.
So i was thinking, you can get epoxy stuff for lining fuel tanks, can you get anything suitable for lining a coolant header tank?
Krikkit said:
I wouldn't think anything in antifreeze will affect the fuel tank lining stuff too much if nothing else comes up. What about a repair and powder coating inside?
I'm not big on powder coating as a long term rust inhibitor, as we all know (yes im an EX-TVR owner), it quickly cracks off and the problems just start all over again...doogz said:
Your header tank is unlikely to be flexing in such a manner than promotes cracking of the coating, in the same way that it tends not to crack and peel off of wheels, they're generally too stiff, whereas a chassis is designed to not be completely rigidly stiff, and will flex in a manner than the coating won't like.
Actually, its not a classic round cylindrical tank, its flat and square, so the sides will actually flex quite a bit as the pressure builds up in the system. However i do see what you are saying. Still a no from me though.doogz said:
Fair enough. Use the old one as a template to construct a new one and have it galvanised?
Even if you need to have a boss or two welded in for senders/sensors, shouldn't cost too much to have made, assuming you can't do it yourself?
That's an idea, not sure where I could get that done though, I wouldnt be able to do that myself, I can weld, I can cut, but I cant form sheet metal!Even if you need to have a boss or two welded in for senders/sensors, shouldn't cost too much to have made, assuming you can't do it yourself?
This sealant idea is more of a temporary measure until i can do something more permanent.
you can get stuff to line old fuel tanks with to stop rust getting in to the delivered fuel. Mix it as a liquid, pour it in and then shake it around to ensure coverage.
Maybe one of those would work, my only concern would be if the anti freeze would attack the coating.
Here you go : http://www.frost.co.uk/por15-fuel-tank-sealers.htm...
POR15 is am american product, so you could email them direct and see what they say, be worth asking Frosts too.
Maybe one of those would work, my only concern would be if the anti freeze would attack the coating.
Here you go : http://www.frost.co.uk/por15-fuel-tank-sealers.htm...
POR15 is am american product, so you could email them direct and see what they say, be worth asking Frosts too.
Edited by Crafty_ on Tuesday 23 April 20:51
Is it a ferrari part or a parts bin special? As you might find it is common to other cars which are cheaper
What shape is the tank? It might be easy to make if it is a nice regular shape
How big is the tank? This might be a nice get out as you could split the current tank in two and build a nice alloy tank that will fit inside the current tank
What shape is the tank? It might be easy to make if it is a nice regular shape
How big is the tank? This might be a nice get out as you could split the current tank in two and build a nice alloy tank that will fit inside the current tank
As you are in derby, if you want one made, try these guys the other side of Mansfield.
http://www.a1flues.co.uk/contact
They can form anything from sheets of steel. My brother used to work there once upon a time. If you pm me, you can name drop my old boss, who is a big pal of the owner.
http://www.a1flues.co.uk/contact
They can form anything from sheets of steel. My brother used to work there once upon a time. If you pm me, you can name drop my old boss, who is a big pal of the owner.

McWigglebum4th said:
Is it a ferrari part or a parts bin special? As you might find it is common to other cars which are cheaper
What shape is the tank? It might be easy to make if it is a nice regular shape
How big is the tank? This might be a nice get out as you could split the current tank in two and build a nice alloy tank that will fit inside the current tank
Its not a parts bin / catalog part AFAIK, this is it:What shape is the tank? It might be easy to make if it is a nice regular shape
How big is the tank? This might be a nice get out as you could split the current tank in two and build a nice alloy tank that will fit inside the current tank
And yes, they want £250 for it!!!!!!!!!
its not a "completely totally stupid" price, but its enough to look at longer lasting alternatives first.
You would be hard pressed to get one made for £250 unless you are handy with a TIG yourself.
However if you feel so inclinded you could look at a small production run at some one like alisport and sell them onwards to others with the same problem and you could end up costing you less then £250.
However if you feel so inclinded you could look at a small production run at some one like alisport and sell them onwards to others with the same problem and you could end up costing you less then £250.
Gassing Station | General Gassing | Top of Page | What's New | My Stuff


