Fixing rust myself
Author
Discussion

illmonkey

Original Poster:

19,842 posts

229 months

Wednesday 1st May 2013
quotequote all
Recently purchased a vehicle with some rust on the front wings, which I was going to get done professionally, but was wondering if its worth giving it a bash myself. I've never welded before, but pick stuff up quickly and have access to a few professionals at work who I can get some help from.

I imagine the procedure is to either cut the rusty part off and weld a new shaped piece in, then strip the paint back and respray (I also have a spray booth).

Worth a pop?

Dr Interceptor

8,183 posts

227 months

Wednesday 1st May 2013
quotequote all
Worst case scenario - you muck it up and take it to a pro for a new wing anyway.

If you fancy a go, have a go.

SebastienClement

1,952 posts

171 months

Wednesday 1st May 2013
quotequote all
Might be easier to get a couple of new (pattern?) wings and try swapping them yourself? Isn't much of a job on a lot of cars smile

Harding91

430 posts

200 months

Wednesday 1st May 2013
quotequote all
Google it, read multiple sources and learn what you can

then give it a bash. worst comes to worst you buy a new wing, if it works out then it should be a bit cheaper plus you've learned something new smile

Main thing i would say is dont be afraid to make it worse before it gets better.


Crafty_

14,234 posts

231 months

Wednesday 1st May 2013
quotequote all
what car is it ?

If its even vaguely modern just buy a new (or used if you have to) wing, paint, bolt/spot weld on, job done.

If its something a bit more challenging then you need some kit.
Avoid gasless mig welders
Avoid SIP and various other cheap welders.

Half of your battle will be welding, the other shaping your patch panels to fit the contours of the wing. For this you need hammers & dollys, maybe some mallets and a sandbag too. You might even want to get in to an english wheel, but we're talking proper money now.

Look at these sites:
http://www.metalmeet.com/
http://mig-welding.co.uk/

Also here: http://www.trifive.com/forums/forumdisplay.php?f=3...
The guy that posts there as MP&C does some very, very neat work and has plenty of tips for how to work metal.

orangesrule

1,976 posts

179 months

Wednesday 1st May 2013
quotequote all
I'd just go to a scrapies and get some good wings, or look on ECP, they are like £33 each posted for pattern ones for my car! (e36 bmw)

paintman

7,861 posts

221 months

Wednesday 1st May 2013
quotequote all
As has already been said, depending what the car is you may be better just buying new wings - or good used ones - & save yourself a lot of work.

G600

1,480 posts

218 months

Wednesday 1st May 2013
quotequote all
Crafty_ said:
what car is it ?
You might even want to get in to an english wheel, but we're talking proper money now.
Some serious skill as well to wheel panels.

DaveCWK

2,425 posts

205 months

Wednesday 1st May 2013
quotequote all
Crafty_ said:
Avoid gasless mig welders
For a newbie starting out I would have to disagree with that. I learned to weld on my old mr2 when the sills faied on the MOT. Bought a Clarke 130amp gas/gasless MIG welder from machinemart and it worked a treat. Yes it's a bit more smoky and the welds aren't as neat but when you are starting out they won't be that good anyway, and once they are ground down it dosen't matter anyway. Being able to do it outside your house in the wind and not having to worry about the gas running out are additional bonuses.

Leptons

5,493 posts

207 months

Wednesday 1st May 2013
quotequote all
DaveCWK said:
For a newbie starting out I would have to disagree with that. I learned to weld on my old mr2 when the sills faied on the MOT. Bought a Clarke 130amp gas/gasless MIG welder from machinemart and it worked a treat. Yes it's a bit more smoky and the welds aren't as neat but when you are starting out they won't be that good anyway, and once they are ground down it dosen't matter anyway. Being able to do it outside your house in the wind and not having to worry about the gas running out are additional bonuses.
I had a gas less mig, burning through on every weld is not fun. They do have their place but its on thicker metal rather than bodywork IMO. Especially for a novice.

B'stard Child

31,183 posts

277 months

Wednesday 1st May 2013
quotequote all
Leptons said:
DaveCWK said:
For a newbie starting out I would have to disagree with that. I learned to weld on my old mr2 when the sills faied on the MOT. Bought a Clarke 130amp gas/gasless MIG welder from machinemart and it worked a treat. Yes it's a bit more smoky and the welds aren't as neat but when you are starting out they won't be that good anyway, and once they are ground down it dosen't matter anyway. Being able to do it outside your house in the wind and not having to worry about the gas running out are additional bonuses.
I had a gas less mig, burning through on every weld is not fun. They do have their place but its on thicker metal rather than bodywork IMO. Especially for a novice.
^ Agreed - All you do when trying to learn with a gasless mig is make it bloody hard for yourself!!!