CV joint grinding noise????
Discussion
Hi All,
Recently I haveheard quite an audible grinding noise at low speed from my Polos front end.
Its like a loud rubbing noise, I have always been under the impression that CV joints make a "clicking noise" but is it possible for them to make a grinding noise, worse when any amount of angle is on the steering wheel.
After changing my discs and pads successfully I now feel like a mechanical god of automotives.... So, is replacing the CV joints something DIYable?
Recently I haveheard quite an audible grinding noise at low speed from my Polos front end.
Its like a loud rubbing noise, I have always been under the impression that CV joints make a "clicking noise" but is it possible for them to make a grinding noise, worse when any amount of angle is on the steering wheel.
After changing my discs and pads successfully I now feel like a mechanical god of automotives.... So, is replacing the CV joints something DIYable?
That will tell you if wheel bearings are knackered, but they may or may not be the source of your noise.
I had a Citroen that made a grinding noise on left-hand turns. Replaced wheel bearings (both sides), cv joint, driveshaft centre bearing, then the whole o/s driveshaft. Still made the noise. I just lived with until, about 6 months later, I realised the noise had stopped of its own accord.
To replace your wheel bearings you'll need access to a hydraulic press to remove old one and fit new one, once you've got the hub carrier off the car (for which you'll need a balljoint splitter of some type)
I had a Citroen that made a grinding noise on left-hand turns. Replaced wheel bearings (both sides), cv joint, driveshaft centre bearing, then the whole o/s driveshaft. Still made the noise. I just lived with until, about 6 months later, I realised the noise had stopped of its own accord.
To replace your wheel bearings you'll need access to a hydraulic press to remove old one and fit new one, once you've got the hub carrier off the car (for which you'll need a balljoint splitter of some type)
tigger1 said:
Had this on an old clio. A seal on the joint had gone, pissing grease everywhere - so joint was dry. Could be similar.
Would that mean a unit replacement or just the boot? Mind you, you need to take the unit off to replace the boot so a whole unit change would probably be best.boyse7en said:
To replace your wheel bearings you'll need access to a hydraulic press to remove old one and fit new one, once you've got the hub carrier off the car (for which you'll need a balljoint splitter of some type)
I'd have a bash with a hammer and a blowtorch personally.Only VW I've ever done this on was an early Golf GTi, but for seperating the joints you can use this:
http://www.machinemart.co.uk/shop/product/details/...
£6 and lasts a lifetime.
OP,
Check the wheel bearings. There's a million guides as to how. Also inspect the CV boot.
Rotating the wheel whilst your under it should give you some idea as to where the problem lies. If you can't replicate the sound on the jack it would point to the wheel bearing.
If you're doing it on the cheap and can't be sure of which it is replace the cheapest part first.
Check the wheel bearings. There's a million guides as to how. Also inspect the CV boot.
Rotating the wheel whilst your under it should give you some idea as to where the problem lies. If you can't replicate the sound on the jack it would point to the wheel bearing.
If you're doing it on the cheap and can't be sure of which it is replace the cheapest part first.
Prof Prolapse said:
OP,
Check the wheel bearings. There's a million guides as to how. Also inspect the CV boot.
Rotating the wheel whilst your under it should give you some idea as to where the problem lies. If you can't replicate the sound on the jack it would point to the wheel bearing.
If you're doing it on the cheap and can't be sure of which it is replace the cheapest part first.
Not doing on the cheap per se, just after doing my brakes last weekend has given me the "bug" so anything that I can do at home I will have a crack at pulling apart myself....Check the wheel bearings. There's a million guides as to how. Also inspect the CV boot.
Rotating the wheel whilst your under it should give you some idea as to where the problem lies. If you can't replicate the sound on the jack it would point to the wheel bearing.
If you're doing it on the cheap and can't be sure of which it is replace the cheapest part first.
I will wait till I get home tonight and check wheel bearings, unfortunately I do not have access to a hydraulic press so may be out of my hands. How much on average would I expect to pay for wheel bearings to be replaced?
About an hours labour plus about £30 for the bearing a side. Depends on charge per hour and what bearings they use.
It's a piece of piss job so take it to a monkey garage and supply the part yourself to keep costs down. I would get a reasonable quality bearing to replace it with personally.
(If it's the bearing!)
It's a piece of piss job so take it to a monkey garage and supply the part yourself to keep costs down. I would get a reasonable quality bearing to replace it with personally.
(If it's the bearing!)
Prof Prolapse said:
About an hours labour plus about £30 for the bearing a side. Depends on charge per hour and what bearings they use.
It's a piece of piss job so take it to a monkey garage and supply the part yourself to keep costs down. I would get a reasonable quality bearing to replace it with personally.
Ah excellent, not too much of a sting then!It's a piece of piss job so take it to a monkey garage and supply the part yourself to keep costs down. I would get a reasonable quality bearing to replace it with personally.
I will get a reasonably priced bearing as I am going to get rid of this liability of a car as soon as I clear the intermittent ABS fault and the intermittent "check engine" light..... bloody thing!!!
Edited by speed_monkey on Monday 12th August 13:20
Wheel bearings. Jack up the wheel and holding the tyre at 12 - 6 and 9 - 3 try to move the wheel in and out.
Do this cold and after a journey when warm.
If you feel movement check its not play in the steering rack, track rod end or lower ball joints.
CV joint. Have a quick look at the boot and look for any cv grease that has been thrown out when the shaft turns.
Then at walking pace drive in a figure of 8 on full lock. Listen out for any ticking, knocking, grinding or similar.
Hope this helps.
Do this cold and after a journey when warm.
If you feel movement check its not play in the steering rack, track rod end or lower ball joints.
CV joint. Have a quick look at the boot and look for any cv grease that has been thrown out when the shaft turns.
Then at walking pace drive in a figure of 8 on full lock. Listen out for any ticking, knocking, grinding or similar.
Hope this helps.
You're assuming it is the bearing of course, however, it does sound like it. You ought to be able to grab the top of the wheel and pull/push it back and forth to find out, or failing that, jack it up. If there's any kind of clicking movement it's the bearings. CV joints tend to knock when they go.
Both are a job that requires around 200 lb/ft of torque to undo and re-tighten the nut on the end of the driveshaft. You'll need an assistant to stand on the brake pedal while you do this, personally I'd suggest going to a garage, as another poster has suggested, it's not that expensive of a job.
As a general rule of thumb, front wheel bearings make more noise when you turn away from the side that's failing (so turn left for a RH bearing, and vice versa), rear wheel bearings are not so obvious, but will still get louder as you turn.
ETA: This noise didn't start shortly after you replaced the disks/pads by any chance?
Both are a job that requires around 200 lb/ft of torque to undo and re-tighten the nut on the end of the driveshaft. You'll need an assistant to stand on the brake pedal while you do this, personally I'd suggest going to a garage, as another poster has suggested, it's not that expensive of a job.
As a general rule of thumb, front wheel bearings make more noise when you turn away from the side that's failing (so turn left for a RH bearing, and vice versa), rear wheel bearings are not so obvious, but will still get louder as you turn.
ETA: This noise didn't start shortly after you replaced the disks/pads by any chance?
Changing the bearings and joints is pretty simple, as others have said.
Bearing is as simple as press out and press in.
Cv joint is simply knock the old joint off the shaft and push the new one on.
It isn't usually that simple as over time corrosion an a corroded spring clip will make it a right pain.
Bearing is as simple as press out and press in.
Cv joint is simply knock the old joint off the shaft and push the new one on.
It isn't usually that simple as over time corrosion an a corroded spring clip will make it a right pain.
XG332 said:
Changing the bearings and joints is pretty simple, as others have said.
Bearing is as simple as press out and press in.
Cv joint is simply knock the old joint off the shaft and push the new one on.
It isn't usually that simple as over time corrosion an a corroded spring clip will make it a right pain.
I just don't have the tools available to do the bearings (hydraulic press), looking at online guides the CV joints dont look too difficultBearing is as simple as press out and press in.
Cv joint is simply knock the old joint off the shaft and push the new one on.
It isn't usually that simple as over time corrosion an a corroded spring clip will make it a right pain.
Gassing Station | General Gassing | Top of Page | What's New | My Stuff


