Clutch wear indicator
Author
Discussion

iloveboost

Original Poster:

1,531 posts

193 months

Wednesday 25th March 2015
quotequote all
Instead of replacing the clutch after it's died why not use a wear sensor like brake pads?

McWigglebum4th

32,414 posts

235 months

Wednesday 25th March 2015
quotequote all
As its a spinny thing


But some cars have a method of measuring the clutch thickness while it is mounted

shake n bake

2,221 posts

238 months

Wednesday 25th March 2015
quotequote all
What would the point of it be? The 'your clutch is knackered, that's why its slipping' light?

BritishRacinGrin

26,708 posts

191 months

Thursday 26th March 2015
quotequote all
Mostly because Brakes wearing down to nothing can be a safety issue and can stop your from stopping, whereas clutch wear will only stop you starting and so isn't so much of a safety issue.

Also this.

McWigglebum4th said:
As its a spinny thing

MotorsportTom

3,343 posts

192 months

Thursday 26th March 2015
quotequote all
Isn't it called your brain?

As in "I've noticed this vehicle is hard to pull away or the clutch slips like a bd"

Rather than waiting for a bulb to tell you what to do.


Plus it's a spinny thing.

nickofh

604 posts

149 months

Thursday 26th March 2015
quotequote all
It would be handy to know when buying a used car.

Andyjc86

1,149 posts

180 months

Thursday 26th March 2015
quotequote all
Clutches aren't exactly the thickest things anyway, at what point would the indicator come on?

loose cannon

6,059 posts

272 months

Thursday 26th March 2015
quotequote all
6 microns wink were is that piccy of a tongue in bottom lip when you need it

cobra kid

5,627 posts

271 months

Thursday 26th March 2015
quotequote all
loose cannon said:
6 microns wink were is that piccy of a tongue in bottom lip when you need it
the atomic belm?

loose cannon

6,059 posts

272 months

Thursday 26th March 2015
quotequote all
clutch plates have barely 3 or 4 mm each side of the plate when new so crap idea if the clutch is fooked you no as it slips or does nothing sorry was my attempt at humour

Bennet

2,133 posts

162 months

Thursday 26th March 2015
quotequote all
Technically feasible or not, this is no where near as stupid as some of you are pretending it is.

It would be quite nice to know that your clutch is 10%,50%,80% whatever of the way through its useful life. It would also be worth while knowing if your clutch was on its way out just before setting off on an 800 mile round trip.

BritishRacinGrin

26,708 posts

191 months

Thursday 26th March 2015
quotequote all
Bennet said:
Technically feasible or not, this is no where near as stupid as some of you are pretending it is.

It would be quite nice to know that your clutch is 10%,50%,80% whatever of the way through its useful life. It would also be worth while knowing if your clutch was on its way out just before setting off on an 800 mile round trip.
Nice to know? Yeah, I suppose so. Necessary? Nah. Clutches don't just stop engaging, a slipping clutch used sympathetically would easily complete an 800 mile journey.

Krikkit

27,942 posts

212 months

Thursday 26th March 2015
quotequote all
Some of the more sophisticated clutched autos have an estimator for how much clutch is left, presumably based on measurements of how quickly engagement takes place when the actuator is triggered, but it's not very practical in a manual.

You could add an automatic system to find the wear %age, but it's a lot of complexity for not much gain imo.

thatdude

2,660 posts

158 months

Thursday 26th March 2015
quotequote all
One can potentially gauge the wear of a clutch by assessing the "spin down" time; with the engine on and the gearbox in neutral, depress the clutch and try and engage reverse. The longer you have to hold the clutch down before engaging reverse where it doesnt make a horrible crunching / grinding / 'box-destorying-itself-slowly noise, the more your clutch is worn.

It's a bit crude but it's how I figured my clutch was done.

IanCress

4,409 posts

197 months

Thursday 26th March 2015
quotequote all
thatdude said:
One can potentially gauge the wear of a clutch by assessing the "spin down" time; with the engine on and the gearbox in neutral, depress the clutch and try and engage reverse. The longer you have to hold the clutch down before engaging reverse where it doesnt make a horrible crunching / grinding / 'box-destorying-itself-slowly noise, the more your clutch is worn.

It's a bit crude but it's how I figured my clutch was done.
Genuine question - why would the wear on the clutch change the amount of time it takes to 'spin down'? The amount of material worn from the clutch is a tiny percentage of the rotating mass of the clutch, so should barely alter the time at all.

BuzzBravado

2,949 posts

202 months

Thursday 26th March 2015
quotequote all
Just more electronic crap to go wrong.

Mr2Mike

20,143 posts

286 months

Thursday 26th March 2015
quotequote all
iloveboost said:
Instead of replacing the clutch after it's died why not use a wear sensor like brake pads?
Because clutches don't normally just "die" with no warning, whereas brake performance to the average plodding driver doesn't change significantly until they hit metal.

With clutches the bite point tends to move up, it gets heavier, sometimes it starts dragging making gearchanges stiffer and finally it will start slipping under load, but the car will remain driveable for quite some time if driven with care. At that point the clutch is pretty much dead but you've had loads of warning, so what's the point of an idiot light telling you these things are going to occur some random length of time in the future?

Mr2Mike

20,143 posts

286 months

Thursday 26th March 2015
quotequote all
IanCress said:
thatdude said:
One can potentially gauge the wear of a clutch by assessing the "spin down" time; with the engine on and the gearbox in neutral, depress the clutch and try and engage reverse. The longer you have to hold the clutch down before engaging reverse where it doesnt make a horrible crunching / grinding / 'box-destorying-itself-slowly noise, the more your clutch is worn.

It's a bit crude but it's how I figured my clutch was done.
Genuine question - why would the wear on the clutch change the amount of time it takes to 'spin down'? The amount of material worn from the clutch is a tiny percentage of the rotating mass of the clutch, so should barely alter the time at all.
You thinking about the wrong thing, with material removal it should be quicker to spin down, not slower. When the clutch friction material wears, the fingers of the diaphragm spring move out towards the release bearing (or inward for a 'pull' style clutch). This causes the bite point at the pedal to rise, but it also reduces the movement of the pressure plate for a given travel of the clutch pedal so clutch drag tends to increase. This is why it becomes more difficult to engage gears, especially from a standstill.

AC43

13,719 posts

239 months

Thursday 26th March 2015
quotequote all
I've got one it the wife's Clio. When I let the clutch out and my knee hits the back of the steering before it moves off the clutch is gone.


IanCress

4,409 posts

197 months

Thursday 26th March 2015
quotequote all
That makes sense Mike, thanks.