P0140 Engine Code - Poor Fuel Economy?
P0140 Engine Code - Poor Fuel Economy?
Author
Discussion

NobleGuy

Original Poster:

7,133 posts

246 months

Sunday 5th April 2015
quotequote all
I've scanned my Hyundai Getz and it came up with P0140 - 02 Sensor Circuit No Activity Detected (Bank 1 Sensor 2)

This is an error for the post-cat sensor, but would this cause poor fuel economy and higher than average emissions if it's failed?
I always thought the first (pre-cat) sensor was responsible for maintain fuel mixture and the post-cat was purely a monitor?

kambites

71,716 posts

252 months

Sunday 5th April 2015
quotequote all
As far as I know, the post-cat sensor only exists to monitor the cat. I'm not aware of manufacturers using it for mixture control. I guess there's no reason that a manufacturer shouldn't use it for more, though.

Roo

11,504 posts

238 months

Sunday 5th April 2015
quotequote all
kambites said:
As far as I know, the post-cat sensor only exists to monitor the cat. I'm not aware of manufacturers using it for mixture control. I guess there's no reason that a manufacturer shouldn't use it for more, though.
This is what I've been told.

One of my cars neither post cat O2 sensor has power to them so the EML is on but makes no difference to the car and doesn't even show a fault code if you scan it.

NobleGuy

Original Poster:

7,133 posts

246 months

Sunday 5th April 2015
quotequote all
Hmmm...so that fact it failed its emissions at MOT may not have anything to do with the post-cat sensor?

I've had a look just now and unbolted the shield from around the manifold area - obvious cracks in it...
Is this perhaps more likely to be causing my poor fuel economy and high emissions?

kambites

71,716 posts

252 months

Sunday 5th April 2015
quotequote all
Does your OBD reader let you monitor the fuel trim and sensor data in real-time? Last time I had an issue like that it turned out the pre-cat sensor was on its last legs but not failing badly enough to throw up a fault code. It was pretty obvious from the ECU telemetry that it was screwed.

Roo

11,504 posts

238 months

Sunday 5th April 2015
quotequote all
Air getting in would weaken the mixture which may be causing the ecu to over compensate.

NobleGuy

Original Poster:

7,133 posts

246 months

Sunday 5th April 2015
quotequote all
kambites said:
Does your OBD reader let you watch the fuel trim in real-time whilst driving?
I've only just bought is but it's pretty basic - not 100% sure but I'd guess probably not.

kambites

71,716 posts

252 months

Sunday 5th April 2015
quotequote all
NobleGuy said:
kambites said:
Does your OBD reader let you watch the fuel trim in real-time whilst driving?
I've only just bought is but it's pretty basic - not 100% sure but I'd guess probably not.
This is why I don't like stand-alone OBD readers. The ones that connect to a computer or a phone are so much more flexible. frown

bearman68

4,942 posts

163 months

Sunday 5th April 2015
quotequote all
Post cat Oxy sensor will have no effect on fuel trim. (or economy)
The last few cars I have done, I've changed both the cat and the pre cat O2 sensor, as I reckon the life of both is about the same. If you have an OBD sacanner, check out the long and short term fuel trim. Long term +/- 10% is OK. Short term should cycle hi / lo about every second. Longer than this and you may have a problem.

Hope this helps a bit.

Cheers

NobleGuy

Original Poster:

7,133 posts

246 months

Monday 6th April 2015
quotequote all
Thanks for all the replies guys, really appreciate it smile

I think the manifold might be the place to start as it looks like it's almost in three pieces :-o
After breaking my knuckles on rust for a while, where can I get high temp bolts to put a new one back on?

kambites

71,716 posts

252 months

Monday 6th April 2015
quotequote all
NobleGuy said:
Thanks for all the replies guys, really appreciate it smile

I think the manifold might be the place to start as it looks like it's almost in three pieces :-o
After breaking my knuckles on rust for a while, where can I get high temp bolts to put a new one back on?
The obvious place would be a main dealer for whatever car it is. When I needed some stretch bolts for the wife's Skoda they were only 50p each at the main dealer so not really worth trying to find them anywhere else.

NobleGuy

Original Poster:

7,133 posts

246 months

Monday 6th April 2015
quotequote all
kambites said:
NobleGuy said:
Thanks for all the replies guys, really appreciate it smile

I think the manifold might be the place to start as it looks like it's almost in three pieces :-o
After breaking my knuckles on rust for a while, where can I get high temp bolts to put a new one back on?
The obvious place would be a main dealer for whatever car it is. When I needed some stretch bolts for the wife's Skoda they were only 50p each at the main dealer so not really worth trying to find them anywhere else.
Brilliant. Thank you smile