Recommend a cordless impact wrench
Recommend a cordless impact wrench
Author
Discussion

ryanthescot

Original Poster:

287 posts

185 months

Friday 10th April 2015
quotequote all
Anyone use a cordless impact wrench? I've been looking at a compact DeWalt one but I have no idea whether it will be any good or whether it will last. Comes to around £230 with battery and charger, it will mostly be used for removing wheel nuts.

Here's the one on amazon (note it's not got a battery or charger so need to add another £60 and £35)
And here's another one that looks similar

Any recommendations before I buy?

DuraAce

4,272 posts

191 months

Friday 10th April 2015
quotequote all
For wheel nuts you want impact wrench not impact driver, like your second link. You want 1/2 inch drive chuck IMO so you can use decent 1/2 inch drive impact sockets.

I'm looking at buying a Makita one, as I've already got a few of their tools so need don't the battery/charger

I've heard good reports bout the Clarke one from Machine Mart though. Depends on your budget I guess, I'd love the SnapOn version but that's way over my DIY-ers budget! Bloody good piece of kit though.

RobinOakapple

2,802 posts

143 months

Friday 10th April 2015
quotequote all
Most of my cordless stuff is Makita, but I reckon any decent make will have something to suit you.

Andy665

4,222 posts

259 months

Friday 10th April 2015
quotequote all
I have a Ryobi One cordless drill and all the batteries are interchangeable - impressed with the drill so far and the impact wrench will be added next month - pretty good value and seem fairly robust - certainly for an amateur like me

kambites

71,734 posts

252 months

Friday 10th April 2015
quotequote all
RobinOakapple said:
Most of my cordless stuff is Makita
Same here for home DIY type tools but I think you have to use them quite a lot to make them worth the initial premium and if I was using garage tools that much I would be installing a compressor and using air (which is what I've done).

amstrange1

617 posts

207 months

Friday 10th April 2015
quotequote all
My Makita impact driver and 3/8" adaptor is man enough for wheel bolts etc.

Shaun_E

750 posts

291 months

Friday 10th April 2015
quotequote all
The £100 Clarke one from Machine Mart is a good budget choice. It will undo wheel nuts easily enough. The downside is that it is quite heavy and uses NiCad batteries. Mine has finally died so I have just purchased a De Walt DCF880. You can get it as a bare unit or in a pack with charger and 2 batteries. A friend has had one for 10 years and it's still going strong. It is fine for alloy wheel changing and is much lighter than the Clarke one. It also gets a good rating in the AutoExpress impact wrench review.

GTRmad

248 posts

202 months

Friday 10th April 2015
quotequote all
ryanthescot said:
Anyone use a cordless impact wrench? I've been looking at a compact DeWalt one but I have no idea whether it will be any good or whether it will last. Comes to around £230 with battery and charger, it will mostly be used for removing wheel nuts.

Here's the one on amazon (note it's not got a battery or charger so need to add another £60 and £35)
And here's another one that looks similar

Any recommendations before I buy?
Amazon do a Dewalt heavier duty impact wrench for £160 bare unit..
That's the one you want,not the lighter duty one in your link..

Lugy

830 posts

214 months

Saturday 11th April 2015
quotequote all
Now I'm definitely not a Snap-On fan boy, in fact far from it but I can't see past their impact guns, mine is a few generations old now (bought second hand from the US for around £180) and the batteries are starting to discharge a bit quicker but it'll still take off most things I need it too. I'm contemplating buying a newer one but we'll see.
I'd rate the Sealey ones highly too however they're not cheap either, though IMO this is an area that you get what you pay for.

foggy

1,215 posts

313 months

Saturday 11th April 2015
quotequote all
Impact driver for lighter weight screwing & fixings, usually with female hex to accept driver bits. Impact wrench is heavier duty higher torque & stronger blows for wheel nuts etc. battery ones typically with 1/2" male square drive for sockets.

foggy

1,215 posts

313 months

Saturday 11th April 2015
quotequote all
Have used a cheap & cheerful Clarke one & a ~250Nm Makita one at work, both 18V rechargeable. The Clarke one does a great job but is heavy & a bit unwieldy for use in confined spaces. Makita wasn't quite so powerful but still more than enough for normal wheel nut type applications & was nicer in the hand to use. There is a more powerful 450Nm Makita job is, but that means a bigger heavier tool. I generally pick up the smaller Makita unit.

KAgantua

5,193 posts

162 months

Saturday 11th April 2015
quotequote all
does anyone know if these machines have a max torque setting

Slow

6,973 posts

168 months

Saturday 11th April 2015
quotequote all
Got 2 of these at work, only problem is the battery's started to go after a year.

http://www.ebay.co.uk/itm/Sealey-Tools-CP2400-24V-...

kambites

71,734 posts

252 months

Saturday 11th April 2015
quotequote all
anonymous said:
[redacted]
I'd always assumed an impact driver also impacted along the length of the fixing (like the manual things you hit with a hammer) whereas an impact wrench only impacts radially. Not sure though, they might just be different terms for the same thing.

BritishRacinGrin

26,714 posts

191 months

Saturday 11th April 2015
quotequote all
I presume you need a pretty serious bit of kit if you want to do hub nuts and crank pulley bolts as well?

kambites

71,734 posts

252 months

Saturday 11th April 2015
quotequote all
I was only guessing, don't take that as gospel. smile

ryanthescot

Original Poster:

287 posts

185 months

Saturday 11th April 2015
quotequote all
Ok thanks for everyone's input. I was looking at the smaller one as it seems to be reasonably discounted and would be better for getting into tighter areas, but the main thing I want one for is getting wheel nuts off so I'll probably just get a bigger one.

Found a Milwauke one on Gumtree for a reasonable price - http://www.gumtree.com/p/power-tool-drills/milwauk...

Anyone used one of these? Looks like it would be up to the job...