The electrical loom in modern cars
The electrical loom in modern cars
Author
Discussion

Streetrod

Original Poster:

6,484 posts

237 months

Saturday 11th April 2015
quotequote all
I recently bought a new Audi A4 Avant for my daily commute and it came with a very decent spec. But the options list on these cars is huge. So my question is this. Does a modern car electrical loom come as one standard package with all the wiring needed to accommodate any options ordered or is it tailored at production time so as to only provide the wiring required?

My thoughts are that to simplify things the loom is the same in each car so keeping customisation and additional costs to a minimum. Therefore if for instance I wanted to fit electrical seats to my car would the wiring already be in place so that I could plug and play. I am right in this thinking?

bobtail4x4

4,462 posts

140 months

Saturday 11th April 2015
quotequote all
yes but the car needs the ecu altering to make things work.

AJB

856 posts

246 months

Saturday 11th April 2015
quotequote all
I'm not an expert, but I'd say no. I haven't seen unplugged connectors on recent-ish cars I've tinkered with, and there would be loads if they had a standard loom to cater for all options. I think wiring looms are pretty much built to order car-by-car on many makes now. When I went round the MINI factory that's the impression they gave - the loom turned up in a large bag, made for that specific car.

alecescolme

2,149 posts

155 months

Saturday 11th April 2015
quotequote all
In my experience I would say no, with my Jag, I found that:
a. Basic loom, poverty spec
b. Loom with provision for most options, premium sound, nav, voice, phone, ect
c. Top spec loom, rear TVs, ect.

DuraAce

4,272 posts

191 months

Saturday 11th April 2015
quotequote all
I'd say no also. There will,be some exceptions of course but generally manufacturers won't watse money giving you extra wiring for options that aren't fitted.

Speaking generally, you might find there will be some pre existing wiring for minor options like a CD player or interior lights etc. I reckon you've no chance of wiring for big stuff like heated seats, sunroofs, power seats etc

In my experience of owning Audi (A4 B7) the wiring for seats, xenons and nav system wasn't fitted from the factory.

Edited by DuraAce on Saturday 11th April 18:50

bearman68

4,942 posts

163 months

Saturday 11th April 2015
quotequote all
alecescolme said:
In my experience I would say no, with my Jag, I found that:
a. Basic loom, poverty spec
b. Loom with provision for most options, premium sound, nav, voice, phone, ect
c. Top spec loom, rear TVs, ect.
Could quite see this being the way of things. In my experience of many makes, I have found part looms missing - For example, the wires go to a body control unit, but the loom from the connection block in the BCU to the (for example) heated seats is missing. You would need to purchase that section of loom, fit, and then programme the BCU to recognise the heated seats. (and find some way of sending the start signal.

Superhoop

4,919 posts

224 months

Saturday 11th April 2015
quotequote all
Another No. There will be some spare connectors kicking around for some options, but higher spec vehicles basically have a higher spec loom.

You seem to suggest that there is only one loom in the car, in the case of French cars, that may be the case, but in the main, manufacturers use multiple harness' (emissions harness, front harness, rear harness, dash harness etc..) as much as anything else, but to make it easy to offer differing engine options.

They definitely don't make one harness to save cost, as it costs more money to put redundant wiring into a car, because that redundant wiring costs money.

Mr Tidy

31,927 posts

158 months

Saturday 11th April 2015
quotequote all
I was idly wondering about a few upgrades for my 2006 Z4 Coupe and it seems that pre-facelift Z4's were pre-wired for some items like CD Changer & Cruise but post facelift models weren't.
I think pre-wiring is becoming much less common as time passes - perhaps it's because there are so many options now and/or possibly because more modern manufacturing methods make it easier to build a specific loom for each car.

HTP99

25,452 posts

171 months

Saturday 11th April 2015
quotequote all
In the late 90's/early 2000's I worked for a VW dealer in the parts dept.

There was the odd issue with wiring looms on the MKIV Golf, in some instances the whole loom needed replacing, in order to order a new one we had to send off the details of the car including spec details, these details were on a white sticker in the boot; this sticker had the chassis number and various codes, (if I remember correctly, these codes were called "PR" numbers) these codes detailed the exact spec and options the car had.

With these codes a specific loom for the car could be made, however it was handmade and would take months to obtain.

So; in the not too distant past, the looms were individual for each car; now, I don't know, however I would have though that they still are, however with multiplex wiring being the norm now, there are less wires needed as one wire can do the job that a few wires did a decade or so ago.




Nickbrapp

5,277 posts

161 months

Saturday 11th April 2015
quotequote all
Fords do, my focus has the plugs in place for Mood lighting etc

Also a lot of options in vag cars can be programmed with vag com such as corner fogs

kambites

71,734 posts

252 months

Saturday 11th April 2015
quotequote all
These days, the loom seems to be a 12V power supply and serial bus with a slave ECU at every end-point, rather than separate cables for every component so the question is whether manufacturers supply the master ECU code to drive all possible slave devices in all cars... I rather suspect that they do, but the need for bus processing logic will mean that the extra components aren't as cheap as they might have been in the past.

*Al*

3,830 posts

253 months

Saturday 11th April 2015
quotequote all
I work for Honda (HUM) manufacturing the Civic, CRV and Jazz and can confirm we have many different 'specs' of harness. Harness looms are now relatively small compared to high spec looms of old because of the CANBUS systems.

Spare tyre

12,750 posts

161 months

Saturday 11th April 2015
quotequote all
I was fiddling with a transit van the other day

It only had the wiring for the stuff it had

djdest

6,542 posts

209 months

Saturday 11th April 2015
quotequote all
Also worth noting that some have MOST (Media Oriented Systems Transport), which is basically a fibre optic cable loop into which you can add modules relating to the stereo etc such as idrive, cd changers, tv tuners, phone etc which can save a lot of wiring

Cyder

7,190 posts

251 months

Saturday 11th April 2015
quotequote all
It's impossible to say, some things will be given away and for others you'll have to put a different spec level ECU in.

AJB

856 posts

246 months

Sunday 12th April 2015
quotequote all
kambites said:
These days, the loom seems to be a 12V power supply and serial bus with a slave ECU at every end-point, rather than separate cables for every component so the question is whether manufacturers supply the master ECU code to drive all possible slave devices in all cars... I rather suspect that they do, but the need for bus processing logic will mean that the extra components aren't as cheap as they might have been in the past.
But the other question is whether the loom has a connector at every possible endpoint. So whilst you're right that the ECU might well be able to support all end points (eg an Audi MMI and/or HVAC ECU could almost certainly be configured to enable heated seats control, and any on-screen displays or controls would spring into life), the loom might not have wires for the physical heated seat switches to connect to that ECU, and the loom probably wouldn't have a spur or a connector to go up into the seat if that's where the seat electrics ECU would go if/when fitted.

robinessex

12,044 posts

212 months

Sunday 12th April 2015
quotequote all
In the good old days, when production wasn't as automated and computer controlled as now, and cars were simpler those days, there was only 1 wiring loom. I remember my Dad buying a MK111 Cortina, and some electrical bits and bobs not fitted did have the required bit of wire in the loom. Looms are automated manufacture, so it's easy to programme up the the process to make the loom car specific.

Durzel

13,029 posts

199 months

Sunday 12th April 2015
quotequote all
Given the significance of some options as has been said already having all the wiring in situ would be more expensive than simply manufacturing different spec looms to begin with.

Porsche, for example, have active suspension damping (PASM) as an option on some cars. If you don't spec it from new it can't (as far as I'm aware) be retrofitted as the wiring just isn't there.

Jader1973

5,242 posts

231 months

Sunday 12th April 2015
quotequote all
robinessex said:
Looms are automated manufacture, so it's easy to programme up the the process to make the loom car specific.
Are you sure about that? My experience across two OEMs is that they are made manually on a board, which is why they are made in countries with very low wages like bits of Eastern Europe and Asia by unskilled labour.

As for types, there will be lots, possibly one for each model and body type.

Willy Nilly

12,511 posts

198 months

Sunday 12th April 2015
quotequote all
*Al* said:
I work for Honda (HUM) manufacturing the Civic, CRV and Jazz and can confirm we have many different 'specs' of harness. Harness looms are now relatively small compared to high spec looms of old because of the CANBUS systems.
Next time you are at work, can you walk up to the person that decided not to supply Hondas with spare wheels and kick him as hard as you possibly can in the bks please? Thanks.