Electronics/pcb whizz needed
Electronics/pcb whizz needed
Author
Discussion

Leptons

Original Poster:

5,493 posts

207 months

Saturday 11th April 2015
quotequote all
Being a tight Yorkshireman I refuse to throw anything away and fix everything where possible.

I'm trying to replace a Transistor in the box of tricks that controls the Hood in My E36 Cabriolet. It has burnt out which is I'm guessing what's causing it not to work.

There is a bank of 6 of them, the one pictured on the left is identical to the Thats burnt out.



I tried replacing it with a similar looking component. It turned out to be a voltage regulator so didnt last long before it popped although it did make the box of tricks work temporarily.

I've got a "lucky dip bag" of transistors from Maplin its all I could find. I can't seem to find an exact replacement so is there anything I could use as an alternative?

Cheers

gazza285

11,266 posts

239 months

Saturday 11th April 2015
quotequote all
Short arms and deep pockets.

Post a better photo, I can't be bothered trying to make out the part numbers.

saaby93

32,038 posts

209 months

Saturday 11th April 2015
quotequote all
Leptons said:
Being a tight Yorkshireman I refuse to throw anything away and fix everything where possible.

I'm trying to replace a Transistor in the box of tricks that controls the Hood in My E36 Cabriolet. It has burnt out which is I'm guessing what's causing it not to work.

There is a bank of 6 of them, the one pictured on the left is identical to the Thats burnt out.


I tried replacing it with a similar looking component. It turned out to be a voltage regulator
^^^ rofl ^^^

See the one that has BUK455 on it what did the busted one have?


Leptons

Original Poster:

5,493 posts

207 months

Saturday 11th April 2015
quotequote all
BUK455 50A

It's made by Phillips but I can't seem to find a direct replacement.

grayze

790 posts

199 months

Toltec

7,179 posts

254 months

Saturday 11th April 2015
quotequote all

OldGermanHeaps

5,192 posts

209 months

Saturday 11th April 2015
quotequote all
Mosfets dont usually just fail in isolation, there has either been an overcurrent or some other fault that caused it to fail in the first place, you may also have 1 or 2 resistors open or diodes shorted elsewhere in the vicinity.

Mr2Mike

20,143 posts

286 months

Saturday 11th April 2015
quotequote all
The BUK455 is a pretty old device, but you can still pick them up on eBay.

Note that standing the component up on its legs and connecting the tab with a short wire is not an acceptable method of mounting them. They are soldered down to the PCB to provide heatsinking for the device, and will likely run too hot if not mounted correctly, not to mention they will quickly fall off the board from vibration!


Edited by Mr2Mike on Saturday 11th April 22:56

Toltec

7,179 posts

254 months

Saturday 11th April 2015
quotequote all
OldGermanHeaps said:
Mosfets dont usually just fail in isolation, there has either been an overcurrent or some other fault that caused it to fail in the first place, you may also have 1 or 2 resistors open or diodes shorted elsewhere in the vicinity.
The capacitor? straight above the transistor he has replaced does not look too healthy.

Sheepshanks

41,402 posts

150 months

Saturday 11th April 2015
quotequote all
Even if there was no other fault, it would overheat rapidly if it wasn't soldered down on the board properly.

Mr2Mike

20,143 posts

286 months

Saturday 11th April 2015
quotequote all
Toltec said:
Neither of those are straight equivalents, though they may work. They both have a considerably higher maximum drain current, and lower Rds(on) than the BUK455 which should be fine, but they also a much lower maximum Vds (60v vs 200v for the BUK455) which could be a problem. The maximum Vgs is also lower (20v vs 30v) though unlikely to be an issue in this case.

Leptons

Original Poster:

5,493 posts

207 months

Saturday 11th April 2015
quotequote all
Sheepshanks said:
Even if there was no other fault, it would overheat rapidly if it wasn't soldered down on the board properly.
This could be a problem then. Not sure I could get it hot enough without damaging the components around it.

Sheepshanks

41,402 posts

150 months

Saturday 11th April 2015
quotequote all
Leptons said:
This could be a problem then. Not sure I could get it hot enough without damaging the components around it.
As others have said, it's entirely feasible that there are other faulty components - indeed possibly even whatever it drives.

iva cosworth

44,044 posts

194 months

Saturday 11th April 2015
quotequote all
Find a secondhand board on Ebay ?

Sounds easier than messing with all these widgets.

anonymous-user

85 months

Sunday 12th April 2015
quotequote all
You'll probably need a hot plate and hot air soldering station to solder large SMC power devices like those, but you can make do by heating the pcb carefully from underneath with a DIY hot air gun, and using a conventional iron on the pad on the top side. Care though, get carried away with the hot air gun and you'll knacker it!

saaby93

32,038 posts

209 months

Sunday 12th April 2015
quotequote all
iva cosworth said:
Find a secondhand board on Ebay ?
or replace it with a relay

anonymous-user

85 months

Sunday 12th April 2015
quotequote all
saaby93 said:
iva cosworth said:
Find a secondhand board on Ebay ?
or replace it with a relay
The layout looks like an H bridge to me, with descrete FETs, which would make sense as the motors probably need to be driven in two directions (hood up/hood down)

Pesty

42,655 posts

287 months

Sunday 12th April 2015
quotequote all
Why have you "soldered" it to the test points/ via holes and not the pads lol. And why up in the air like that.

(Edit I can see why. It's a through hole component with a heat sink so it won't fit flat.)

Nice try though. I agree don't throw anything away try and fix it first. Good effort though. Keep it up.

Edited by Pesty on Sunday 12th April 00:42

eliot

12,000 posts

285 months

Sunday 12th April 2015
quotequote all
Plenty of buk455's on ebay, but not surface mount type. Is there room to fit a small heatsink in the case ?

peterperkins

3,459 posts

273 months

Sunday 12th April 2015
quotequote all
I agree we need some much better photos of that board and the components you are messing with and the general vicinity on the pcb.

Option 1 easiest find a spare board at a breakers/ebay.

Option 2 try and find suitable devices and fix correctly to the board.