Light scratches on Black Metallic Paint
Discussion
Morning,
Would appreciate any assistance. Got a 7 month old black (cosmos black metallic) Merc which has picked up some surface (light - non fingernail deep) scratches on the passenger rear side door, much to my dismay may i add. Looks like branch damage or grit trapped in a cloth at the local car hand wash.
To get this stuff out by hand, i am reading that Farecla G3 Professional Scratch Removal ( the kind you get at Halfords, not the professional body shop variety) is the best thing to use by far.
Anyone have any experience in using this by hand? If i use this product and it works, will it cause any damage to non target areas of the paint? Some people have mentioned a hazing which occurs over the paint, which then needs to be further treated using something else, is this the case? Will the finish require upkeep, i.e. if i dont wax the panel in the future you can tell something has been used?
Would appreciate any assistance. Got a 7 month old black (cosmos black metallic) Merc which has picked up some surface (light - non fingernail deep) scratches on the passenger rear side door, much to my dismay may i add. Looks like branch damage or grit trapped in a cloth at the local car hand wash.
To get this stuff out by hand, i am reading that Farecla G3 Professional Scratch Removal ( the kind you get at Halfords, not the professional body shop variety) is the best thing to use by far.
Anyone have any experience in using this by hand? If i use this product and it works, will it cause any damage to non target areas of the paint? Some people have mentioned a hazing which occurs over the paint, which then needs to be further treated using something else, is this the case? Will the finish require upkeep, i.e. if i dont wax the panel in the future you can tell something has been used?
I use the G3 product and find it very good. I use it with the G3 applicator pad. Easy, quick and effective.
Just use the white applicator from the twin pack. Wet it first as per the instructions.
All I do is then wax the car as normal.
I use the G3 paste quite often, every time one of my cars picks up a blemish.
The Turtle Wax Colour Magic Wax is also wonderful for a periodic wax. It hides all the swirls.
I use Colour Magic a couple of times a year on all my cars. Regular waxing is done with Dodo Juice and Turtle Wax Ice.
I'm sure there's better but these keep my cars looking very nice indeed. I have no complaints.
Just use the white applicator from the twin pack. Wet it first as per the instructions.
All I do is then wax the car as normal.
I use the G3 paste quite often, every time one of my cars picks up a blemish.
The Turtle Wax Colour Magic Wax is also wonderful for a periodic wax. It hides all the swirls.
I use Colour Magic a couple of times a year on all my cars. Regular waxing is done with Dodo Juice and Turtle Wax Ice.
I'm sure there's better but these keep my cars looking very nice indeed. I have no complaints.
Edited by wilwak on Thursday 16th April 10:29
I presume you don't own a machine polisher. Do you know anyone who does? It's literally 10 times harder trying to remove scratches like this by hand than by machine.
In any case, you'll want to use a fine finishing polish/compound (with a different, softer pad) to finish it off and remove any polishing marks / marring, after you've used the cutting compound to get the scratches out.
In any case, you'll want to use a fine finishing polish/compound (with a different, softer pad) to finish it off and remove any polishing marks / marring, after you've used the cutting compound to get the scratches out.
Don't use a hand car wash. You are just going to pick up more of these blemishes. I'm convinced modern machine car washes are better.
If you can catch your fingernail in the scratch then all you will be able to do is make the appearance of the scratch diminish, to where it might not show as much.
(the only way to fix this is to sand the clearcoat down slightly and I'm pretty sure you wont fancy that :-))
If you can't catch your fingernail then is more of a scuff and will buff out with the sort of products you are talking about. Meguiars sell scratch stuff in Halfords that is designed for hand use. You can't really damage the surrounding paint - it's all very gradual.
If you can catch your fingernail in the scratch then all you will be able to do is make the appearance of the scratch diminish, to where it might not show as much.
(the only way to fix this is to sand the clearcoat down slightly and I'm pretty sure you wont fancy that :-))
If you can't catch your fingernail then is more of a scuff and will buff out with the sort of products you are talking about. Meguiars sell scratch stuff in Halfords that is designed for hand use. You can't really damage the surrounding paint - it's all very gradual.
IndyH said:
Would the fine compound be something like the G10 product for finishing? Interesting because a lot of people seem not to be using the G10 at all after the G3... No unfortunately dont know anyone who has a machine polisher.
I'm not familiar with either product but on the face of it, yes it sounds like it. In general, hard cutting compounds are designed for *correction*, and the finer finishing compounds are for, well, finishing and making it look as deep and shiny as possible 
Lots of car detailers will do this for you without the risk of making it worse, as long as you pick one that's experienced and not just added "detailing" to their sign because they think using Farecla instead of T-Cut makes them a detailer.
Personally I wouldn't be learning to use a machine polisher on a 7-month-old Mercedes.
Back when I had a better web connection and time to kill I used to while away ages looking at the detailing "before and after" threads on places like the detailingworld and Luxury4Play sites - some great cars made to look better than new.
Personally I wouldn't be learning to use a machine polisher on a 7-month-old Mercedes.
Back when I had a better web connection and time to kill I used to while away ages looking at the detailing "before and after" threads on places like the detailingworld and Luxury4Play sites - some great cars made to look better than new.
http://www.detailingworld.co.uk/forum/showthread.p...
Topic here on detailing world about scratch removal
Topic here on detailing world about scratch removal
WOAH STOP RIGHT THERE.
Sorry to sound alarming, but Mercedes paint is very different to other cars. Most mercs have a ceramic outer coating (ceramiclear) which is this very hard outer layer of paint (the outermost bit of the clear coat) which is essentially SiO2 - You can read more about it here: http://www.autogeekonline.net/forum/hot-topics-fre...
(For those of you who don't know, Mike Phillips is a well known professional detailer who has published his own books and has his own classes etc.)
In short, you don't want to be abrading the surface of a Mercedes - you'll take that coating off, and then its all soft clear coat under there.
Wash it at home using the 2 bucket method, and stick to hand polishes that have fillers - for example, super resin polish or poorboy's black hole. You can then top it up with wax, be that cheap wax or something more fancy like swissvax!
Sorry to sound alarming, but Mercedes paint is very different to other cars. Most mercs have a ceramic outer coating (ceramiclear) which is this very hard outer layer of paint (the outermost bit of the clear coat) which is essentially SiO2 - You can read more about it here: http://www.autogeekonline.net/forum/hot-topics-fre...
(For those of you who don't know, Mike Phillips is a well known professional detailer who has published his own books and has his own classes etc.)
In short, you don't want to be abrading the surface of a Mercedes - you'll take that coating off, and then its all soft clear coat under there.
Wash it at home using the 2 bucket method, and stick to hand polishes that have fillers - for example, super resin polish or poorboy's black hole. You can then top it up with wax, be that cheap wax or something more fancy like swissvax!
sunnydude959 said:
WOAH STOP RIGHT THERE.
Sorry to sound alarming, but Mercedes paint is very different to other cars. Most mercs have a ceramic outer coating (ceramiclear) which is this very hard outer layer of paint (the outermost bit of the clear coat) which is essentially SiO2 - You can read more about it here: http://www.autogeekonline.net/forum/hot-topics-fre...
(For those of you who don't know, Mike Phillips is a well known professional detailer who has published his own books and has his own classes etc.)
In short, you don't want to be abrading the surface of a Mercedes - you'll take that coating off, and then its all soft clear coat under there.
Wash it at home using the 2 bucket method, and stick to hand polishes that have fillers - for example, super resin polish or poorboy's black hole. You can then top it up with wax, be that cheap wax or something more fancy like swissvax!
A lot of sense in the above however the main problem here is the "hand car wash " !!!Sorry to sound alarming, but Mercedes paint is very different to other cars. Most mercs have a ceramic outer coating (ceramiclear) which is this very hard outer layer of paint (the outermost bit of the clear coat) which is essentially SiO2 - You can read more about it here: http://www.autogeekonline.net/forum/hot-topics-fre...
(For those of you who don't know, Mike Phillips is a well known professional detailer who has published his own books and has his own classes etc.)
In short, you don't want to be abrading the surface of a Mercedes - you'll take that coating off, and then its all soft clear coat under there.
Wash it at home using the 2 bucket method, and stick to hand polishes that have fillers - for example, super resin polish or poorboy's black hole. You can then top it up with wax, be that cheap wax or something more fancy like swissvax!
Blackhole or even SRP will be washed off instantly by a "hand car wash" due to the harsh chemicals most of these places tend to use and paint damage will be inflicted by the less than optimal materials / techniques employed .
Where I to use one of these places to clean my car just once I would be looking at 2 days minimum to repair the damage !!!
Before you decide on a product to remove surface marring by third parties you really need to decide on a maintenance routine that does not include hand car washes !!
sunnydude959 said:
WOAH STOP RIGHT THERE.
Sorry to sound alarming, but Mercedes paint is very different to other cars. Most mercs have a ceramic outer coating (ceramiclear) which is this very hard outer layer of paint (the outermost bit of the clear coat) which is essentially SiO2 - You can read more about it here: http://www.autogeekonline.net/forum/hot-topics-fre...
(For those of you who don't know, Mike Phillips is a well known professional detailer who has published his own books and has his own classes etc.)
In short, you don't want to be abrading the surface of a Mercedes - you'll take that coating off, and then its all soft clear coat under there.
Wash it at home using the 2 bucket method, and stick to hand polishes that have fillers - for example, super resin polish or poorboy's black hole. You can then top it up with wax, be that cheap wax or something more fancy like swissvax!
Re the Ceramiclear paint code, i have checked by cars paint code and can confirm that it does not have the cermiclear option. Apparently this has been made redundant in recent years with improved technology OR it isn't applied on my specification. Sorry to sound alarming, but Mercedes paint is very different to other cars. Most mercs have a ceramic outer coating (ceramiclear) which is this very hard outer layer of paint (the outermost bit of the clear coat) which is essentially SiO2 - You can read more about it here: http://www.autogeekonline.net/forum/hot-topics-fre...
(For those of you who don't know, Mike Phillips is a well known professional detailer who has published his own books and has his own classes etc.)
In short, you don't want to be abrading the surface of a Mercedes - you'll take that coating off, and then its all soft clear coat under there.
Wash it at home using the 2 bucket method, and stick to hand polishes that have fillers - for example, super resin polish or poorboy's black hole. You can then top it up with wax, be that cheap wax or something more fancy like swissvax!
The super resin polish which you recommend might have a filler but it is also abrasive, and would wear down a layer of paint to an extent...
I will not be using a buffer myself lol, best i can do is hand wash the car myself (following the proper methods etc) but as i live in a flat with no electricity or hose pipe in the parking area, i will have to think of something!
I am visiting a Paintless dent removal guy tonight recommended by my local dealership for a tiny ding on the same door, and he says he can assess the situation for me. Likely he will do it....as it is minor i thought i will deal with it myself.
IndyH said:
Re the Ceramiclear paint code, i have checked by cars paint code and can confirm that it does not have the cermiclear option. Apparently this has been made redundant in recent years with improved technology OR it isn't applied on my specification.
The super resin polish which you recommend might have a filler but it is also abrasive, and would wear down a layer of paint to an extent...
I will not be using a buffer myself lol, best i can do is hand wash the car myself (following the proper methods etc) but as i live in a flat with no electricity or hose pipe in the parking area, i will have to think of something!
I am visiting a Paintless dent removal guy tonight recommended by my local dealership for a tiny ding on the same door, and he says he can assess the situation for me. Likely he will do it....as it is minor i thought i will deal with it myself.
What model is your car?The super resin polish which you recommend might have a filler but it is also abrasive, and would wear down a layer of paint to an extent...
I will not be using a buffer myself lol, best i can do is hand wash the car myself (following the proper methods etc) but as i live in a flat with no electricity or hose pipe in the parking area, i will have to think of something!
I am visiting a Paintless dent removal guy tonight recommended by my local dealership for a tiny ding on the same door, and he says he can assess the situation for me. Likely he will do it....as it is minor i thought i will deal with it myself.
IndyH said:
Morning,
Would appreciate any assistance. Got a 7 month old black (cosmos black metallic) Merc which has picked up some surface (light - non fingernail deep) scratches on the passenger rear side door, much to my dismay may i add. Looks like branch damage or grit trapped in a cloth at the local car hand wash.
To get this stuff out by hand, i am reading that Farecla G3 Professional Scratch Removal ( the kind you get at Halfords, not the professional body shop variety) is the best thing to use by far.
Never used that, but Mequiar's ScratchX is excellent. Did the job flawlessly on mine (Obsidianschwarz). No need to wax the panel either, other than for protection.Would appreciate any assistance. Got a 7 month old black (cosmos black metallic) Merc which has picked up some surface (light - non fingernail deep) scratches on the passenger rear side door, much to my dismay may i add. Looks like branch damage or grit trapped in a cloth at the local car hand wash.
To get this stuff out by hand, i am reading that Farecla G3 Professional Scratch Removal ( the kind you get at Halfords, not the professional body shop variety) is the best thing to use by far.
Autoglym SRP is so mildly abrasive as for it to be a non-issue. It will most likely produce an acceptable result.
Autoglym Pain Renovator, on the other hand, is pretty harsh stuff IIRC.
Make sure the panel is absolutely clean before embarking on any paint correction, either by hand or machine. I would use a mild APC solution sprayed on a couple of times, then rinsed off (mini watering can will do) before actually touching the paint at all. Then a soft microfibre with the APC solution or a mild car shampoo to lightly clean the panel. Air dry and maybe use Windolene and a dry MF to finish.
Sounds like a right faff but it'll only take a minute and vastly reduce the chances of making it worse before you even begin.
I have successfull removed horrible scuffs and scratches in black metallic paint with wet sanding and a DA polisher and I am a right numpty when it comes to all this detailing malarky, definitely not an expert.
Before:

After:

Autoglym Pain Renovator, on the other hand, is pretty harsh stuff IIRC.
Make sure the panel is absolutely clean before embarking on any paint correction, either by hand or machine. I would use a mild APC solution sprayed on a couple of times, then rinsed off (mini watering can will do) before actually touching the paint at all. Then a soft microfibre with the APC solution or a mild car shampoo to lightly clean the panel. Air dry and maybe use Windolene and a dry MF to finish.
Sounds like a right faff but it'll only take a minute and vastly reduce the chances of making it worse before you even begin.
I have successfull removed horrible scuffs and scratches in black metallic paint with wet sanding and a DA polisher and I am a right numpty when it comes to all this detailing malarky, definitely not an expert.
Before:

After:

Edited by Barchettaman on Sunday 19th April 09:20
Gassing Station | General Gassing | Top of Page | What's New | My Stuff


