Increase the power and RPM of an engine
Increase the power and RPM of an engine
Author
Discussion

snoopios

Original Poster:

27 posts

194 months

Monday 24th January 2011
quotequote all
Hello fellow piston headers!!
I'm in my second year of Uni studying Mechanical Engineering and we have been assigned the ridiculously boring task of reverse engineering a Honda GX160 engine and then finding ways to increase the power of the overall engine by 50% and increasing the RPM's by 35%.
Could someone please help me out and give me ideas of what i should be looking at to achieve this new spec?
Thanks,
James

nonuts

15,855 posts

260 months

Monday 24th January 2011
quotequote all
Stronger lighter internals, better balanced too. If you can increase the RPM you'll increase the power as long as it's still making similar torque.

Or have a think about it as you're the one doing a degree. hehe

PS. if you think that's boring you should try getting a real job. irked

Edited by nonuts on Monday 24th January 19:16

JB!

5,255 posts

211 months

Monday 24th January 2011
quotequote all
Lightened flywheel, crank, forged an lighter rods an pistons, then try and cram in as much air and fuel as you can, for a bigger bang.

pacman1

7,324 posts

224 months

Monday 24th January 2011
quotequote all
Welcome aboard, perhaps it might be worth posting a link in here to this thread.

Fahd

138 posts

215 months

Monday 24th January 2011
quotequote all
What scope for modification of the original engine specs are you allowed? do you have a budget?

You could consider altering the following:

Exhaust system.
Air intake/ Re-jetting fuel.
Compression.
Cylinder head replacement/ Bore size increase.



Edited by Fahd on Monday 24th January 19:22

sparkybean

221 posts

221 months

Monday 24th January 2011
quotequote all
Boring task? pah.

Raise the rev limit, and put a wilder cam in. Jab dahhn

snotrag

15,754 posts

242 months

Monday 24th January 2011
quotequote all
snoopios said:
studying Mechanical Engineering and we have been assigned the ridiculously boring task of reverse engineering a Honda GX160 engine
Methinks Sir has chosen the wrong course!?

Anyway - basically you need to make it more efficient, gases in, gases out. Blue printed, lightened, balance internals etc, to enable higher revs, and with higher revs comes higher power.

boredofmyoldname

22,655 posts

230 months

Monday 24th January 2011
quotequote all
nonuts said:
PS. if you think that's boring you should try getting a real job. irked
Just what I was thinking, it sounds like the kind of thing some PHers would try to work out after a few beers in their shed.

Qube

437 posts

291 months

Monday 24th January 2011
quotequote all
Insert a domed piston and fit a high lift cam.

Rebore - increase the diameter of the cylinders.

Change the length of the conrod.

Change the compression ratio.

Fit a supercharger

Fit a turbo

Fit nitrous oxide




snoopios

Original Poster:

27 posts

194 months

Monday 24th January 2011
quotequote all
I've got a few things down already but i somehow doubt its everything and this was more to get some new/other ideas/ways to do it;

1. Reduce the weight of the parts
2. Increase cylinder bore
3. Reduce clearance volume?
4. Cam timings
5. Valve lift - increasing valve lobe length
6. Ignition timings
7. Stronger valve springs
8. Valve lobe dimensions for how long the valve is open for

Haha, i am actually trying to get an Industrial Placement at the moment which will hopefully lead to a job smile Already had 3 interviews so fingers crossed!!

There isn't actually any "budget" or something along those lines, it's all theoretical which makes it even more dull cause we don't get to build anything frown

Jimmyarm

1,962 posts

209 months

Monday 24th January 2011
quotequote all

CraigyMc

18,374 posts

267 months

Monday 24th January 2011
quotequote all
snoopios said:
I've got a few things down already but i somehow doubt its everything and this was more to get some new/other ideas/ways to do it;

1. Reduce the weight of the parts
2. Increase cylinder bore
3. Reduce clearance volume?
4. Cam timings
5. Valve lift - increasing valve lobe length
6. Ignition timings
7. Stronger valve springs
8. Valve lobe dimensions for how long the valve is open for

Haha, i am actually trying to get an Industrial Placement at the moment which will hopefully lead to a job smile Already had 3 interviews so fingers crossed!!

There isn't actually any "budget" or something along those lines, it's all theoretical which makes it even more dull cause we don't get to build anything frown
Job number 1 is step 2 on your list. How much can it be bored out by?

If you actually have a target of raising the RPMs by 35% you're going to have to look at making the engine breate better too - these things tend to run out of puff quite fast.

(honda GX160, for those who don't know, is a single pot 4-stroke aircooled engine, often found on low-end go karts, electrical generators etc etc.) 5.5bhp, right?

C

C


Megaflow

11,673 posts

256 months

Monday 24th January 2011
quotequote all
Hve you actaully got to build the engine and prove it, or just do the calulations?

Because to build it and run it is going to cost a lot of money. Its going to need the head ports cleaned up, probably bigger valves, a custom camshaft. Then theres the bottom end, the crank might be ok, but I reckon you'll need rods, pistons and flywheel to increase the rpm by that much.

snoopios

Original Poster:

27 posts

194 months

Monday 24th January 2011
quotequote all
boredofmyoldname said:
nonuts said:
PS. if you think that's boring you should try getting a real job. irked
Just what I was thinking, it sounds like the kind of thing some PHers would try to work out after a few beers in their shed.
Haha, the task itself isn't too bad, its the engine we are using which i find so boring. We were going to use the engine in the Skyline one of the guys in our group has but we weren't allowed to biggrin

snoopios

Original Poster:

27 posts

194 months

Monday 24th January 2011
quotequote all
CraigyMc said:
snoopios said:
I've got a few things down already but i somehow doubt its everything and this was more to get some new/other ideas/ways to do it;

1. Reduce the weight of the parts
2. Increase cylinder bore
3. Reduce clearance volume?
4. Cam timings
5. Valve lift - increasing valve lobe length
6. Ignition timings
7. Stronger valve springs
8. Valve lobe dimensions for how long the valve is open for

Haha, i am actually trying to get an Industrial Placement at the moment which will hopefully lead to a job smile Already had 3 interviews so fingers crossed!!

There isn't actually any "budget" or something along those lines, it's all theoretical which makes it even more dull cause we don't get to build anything frown
Job number 1 is step 2 on your list. How much can it be bored out by?

If you actually have a target of raising the RPMs by 35% you're going to have to look at making the engine breate better too - these things tend to run out of puff quite fast.

(honda GX160, for those who don't know, is a single pot 4-stroke aircooled engine, often found on low-end go karts, electrical generators etc etc.) 5.5bhp, right?

C

C
Well, we did do some calculations to work out how to get the required specs by individual points i.e. how much the cylinder needs to be bored out to get the 50% power increase etc. It doesn't take too much but obviously we can't just think of a single part to work on, the more parts and reasoning we give the better marks we get i suppose. Like i said, i reckon the stuff that i have managed to think of would be good to get some decent marks but there are always some other neat little ways of doing something else which could sound pretty good in a report smile

And yeah, you've got it spot on with the description of the engine we are using. That's why Nitrous and Turbo/Super Chargers wouldn't be a great way to do what we are doing tongue out

steviejasp

1,646 posts

196 months

Monday 24th January 2011
quotequote all
Map it

snoopios

Original Poster:

27 posts

194 months

Monday 24th January 2011
quotequote all
Megaflow said:
Hve you actaully got to build the engine and prove it, or just do the calulations?

Because to build it and run it is going to cost a lot of money. Its going to need the head ports cleaned up, probably bigger valves, a custom camshaft. Then theres the bottom end, the crank might be ok, but I reckon you'll need rods, pistons and flywheel to increase the rpm by that much.
Nope, it's all theoretical, no build needed at all!!

Zad

13,025 posts

267 months

Monday 24th January 2011
quotequote all
General (overly simplistic) guidelines:

1) The head and associated components make the power
2) Everything else just manages it


CraigyMc

18,374 posts

267 months

Monday 24th January 2011
quotequote all
steviejasp said:
Map it
Map what?

CraigyMc

18,374 posts

267 months

Monday 24th January 2011
quotequote all
Zad said:
General (overly simplistic) guidelines:

1) The head and associated components make the power
2) Everything else just manages it
1) so the block bore makes nothing? Errrr....