Nob is on the rollers tomorrow!

[LazyRoss18]

My 3R is booked on at Devil Developments in Littlehampton tomorrow afternoon!

Only mods are custom exhaust, partial hard pipe kit and forge dump valve.

What's everyone's guesses then??

[mgbond]

Hope u are also doing pump wiring upgrade.

It also depends what boost you are going to run. If you are going to run 0.9 bar then I guess 385

[verba1]

Are you getting it remapped there and what exhaust have you fitted ?

[LazyRoss18]

Hi Martin

Only bought the car a few weeks ago, fuel pump and wiring is top of my list! It's only running standard boost 0.7 bar so guessing somewhere around standard power!

[LazyRoss18]

verba1 said:

Are you getting it remapped there and what exhaust have you fitted ?

Nah it's not being mapped there, I'm just having it dyno'd to check everything is safe. Exhaust is an unknown custom jobbie! All mods were on the car when I bought it few weeks ago!

[jdearden]

What time you there as I need lee to adjust Sumin on mine.

[verba1]

best of luck ! say 365 bhp

[steveobes]

What time is it booked in for
Only live around the corner might pop in n say hellow
steve

[LazyRoss18]

Booked in at 1 o'clock guys!

[mgbond]

LazyRoss18 said:

Hi Martin

Only bought the car a few weeks ago, fuel pump and wiring is top of my list! It's only running standard boost 0.7 bar so guessing somewhere around standard power!

If u have put a free flowing exhaust on its best to get it mapped. Although your dyno run will tell u if its now lean.

0.7 bar is suspect it will just be over std so 350ish.

Are u local to littlehampton as I'm in Bognor

[LazyRoss18]

I'm in Horsham!

Not sure how free flowing the exhaust is, was on the car when I bought it, we shall see I guess!!

[LazyRoss18]

Well she made 344bhp and around 420 lb/ft , so as I guessed slightly down on power! Running slightly rich also so looks like remap time!

[steveobes]

Hi Ross
Tried to make it to lees but was running late.
guess that was you in the noble by the lights at crossbush near arundel.
nice looking car mate, n glad that car ran great on the rollers.
steve

[Gadgeroonie]

a stock one usually makes between 330 and 340 so you have a good one

a 1 bar boost upgrade and remap should make 380 - 400

[LazyRoss18]

steveobes said:

Hi Ross
Tried to make it to lees but was running late.
guess that was you in the noble by the lights at crossbush near arundel.
nice looking car mate, n glad that car ran great on the rollers.
steve

Hi Steve, yup that was me, lovely colour your car is! Yeah it made kinda what I expected so gives me a good starting point!

[LazyRoss18]

Gadgeroonie said:

a stock one usually makes between 330 and 340 so you have a good one

a 1 bar boost upgrade and remap should make 380 - 400

Cheers Gadge, sounds good to me! Just got to try and get hold of Yellowshed now!

[ThatPhilBrettGuy]

Hmmm 420ft/lbs at what revs? That's quite high...

[Gadgeroonie]

i remapped my own - pretty good result

before




after




mine runs 2 fuel pumps, an intercooler and stronger actuators

[TuxMan]

Not bad Ross , torque is plenty high though for std gearbox !!! Clutch is only good for 420ftlb so go easy !!
And so he starts on the slippery slope

[mrpbailey]

If its pulling 420 lbft I'd say its been mapped already! Standard should be around 350 - 360 I think?

As a comparison my car made 344 bhp & 362 lbft when standard. After a free flow exhaust I made 365 bhp and lost a couple of torques if I remember correctly.