Config / Project file for MBE ECU #975db392 ?

[Fixanything]

Does anybody have a copy of the MBE Easimap config/Project file for a Noble M400 e.g. 975db???.ec2, I've made a MBE MAP LEAD and have found a Serial to USB adaptor that works (many don't) and can currently use Noble Software, Easimap 4, 5.5 and 6 to see all engine data e.g. Air intake temp, manifold pressure, RPM, coolant temp, throttle setting, battery voltage, fuel injection time, ignition Advance, etc.... and log it(great tool), although you don't need the .ec2 config file for the Noble software, I understand that its best to use the correct Config file when using MBE Easimap software as it taylors the parameters logged/displayed etc...I also have a few sets of Leads available if anybodies interested ?

[andygtt]

Only people like Yellowshed and a couple of others have the codes for the M400 ecu's and they don't share the codes out... this is why there are lots of people mapping the older cars but not the newer ecu's.

[Fixanything]

Andy,

Thanks for the response however, its not the Unlock code I'm after, its just the Noble specific Project / xxx.ec2 Config file to monitor the ECU/Engine parameters, I do not want it for re-mapping.

Cheers

[daddysumo]

I dont think a different ec2 file will give you any more access than you have, what level of access do you have ?
Basic, mid or top level ?

I'm suprised the version 6 works with our ecu's.

Edited by daddysumo on Friday 8th April 09:19

[Fixanything]

Its not a level of access thing, I have all I need (You can select your level of access in the downloadable Easimap software, except the MBE administration level, which I don't think is any use to us anyway).

As far as I am aware, the xxxx.ec2 project/config file is used by the Easimap application software to configure the ECU/Engine parameters measured and displayed for a particular car/engine, for example a config file for a V16 Quad Turbo car would have many more sensors that feed the ECU than we care about or would want to view on the display screen.

If I can't obtain the file, its not the end of the world because you can manually pick what parameters you want to measure, log and display anyway.

Hope I'm making sense !

Cheers

[daddysumo]

What you are after is the 975 dashboard page.
Which indeed can support two lambda sensors etc etc.
I am suprised you can pick the level on the page you are using as usually it is password protected.
You can of course custom pick the parameters you want to view and store them into a new page of your own....

[key750]

Fixanything said:

Does anybody have a copy of the MBE Easimap config/Project file for a Noble M400 e.g. 975db???.ec2, I've made a MBE MAP LEAD and have found a Serial to USB adaptor that works (many don't) and can currently use Noble Software, Easimap 4, 5.5 and 6 to see all engine data e.g. Air intake temp, manifold pressure, RPM, coolant temp, throttle setting, battery voltage, fuel injection time, ignition Advance, etc.... and log it(great tool), although you don't need the .ec2 config file for the Noble software, I understand that its best to use the correct Config file when using MBE Easimap software as it taylors the parameters logged/displayed etc...I also have a few sets of Leads available if anybodies interested ?

Hello! I try to connect my MBE to a Netbook, please tell me the make and model of 'USB/RS232 adapter that you use!

I would check the values ​​of lambda in my car because I have a little problem in low idle and sometimes the engine dies, you have found the configuration file .ec2 ??
No one here (Italy) knows the units MBE

Edited by key750 on Monday 6th June 18:31

Edited by key750 on Monday 14th November 16:52

[key750]

I can not do a back up about map in the unit.

It is password protected?

Thank you Alberto