GT Engine Cooling Pipework...
GT Engine Cooling Pipework...
Author
Discussion

sportsandclassic

Original Poster:

3,774 posts

249 months

Sunday 21st August 2011
quotequote all
So after trawling the net for hours I have seen this is a worldwide fault, just not seen many reported cases in u.k....

I have decided to do my own set of pipes as a preventative measure.

Out of interest how many owners would want this mod doing ?

We have aluminium welding facilities on site.

Mike

Dan7357

2,648 posts

239 months

Sunday 21st August 2011
quotequote all
Hi Mike,

I thought it was a 997 issue?


sportsandclassic

Original Poster:

3,774 posts

249 months

Sunday 21st August 2011
quotequote all
Hi,

All GT engines produced use same construction methods.

So turbo engines too.

Mike

keep it lit

3,388 posts

198 months

Sunday 21st August 2011
quotequote all
sportsandclassic said:
Out of interest how many owners would want this mod doing ?
Mike
my engine is coming out soon so yes.

smj996c

319 posts

224 months

Sunday 21st August 2011
quotequote all
Hi Mike, next time mine is in for any length of time I would consider this. - Cheers, Simon

Dan7357

2,648 posts

239 months

Sunday 21st August 2011
quotequote all
How often do you lot take your engines out?


keep it lit

3,388 posts

198 months

Sunday 21st August 2011
quotequote all
Dan7357 said:
How often do you lot take your engines out?
Only in the endless search for more grunt.

Hopefully

Biggriff

2,312 posts

315 months

Sunday 21st August 2011
quotequote all
What does this relate to? Your post is a bit cryptic

all2ofme

855 posts

219 months

Sunday 21st August 2011
quotequote all
What's it fix, Mike, and what does the fix involve? Point me to a page somewhere by all means - no need to re-count it all unnecessarily.

When should it be done (engine out job by the sound of it)?

fioran0

2,410 posts

203 months

Sunday 21st August 2011
quotequote all
I might be picking up a spare cup engine in which case I'll have a set needing welded somewhere.
Won't need engine dismantled in my case. I can pull the pipes off.

Fwiw I believe it's a tricky weld due to the cast alu and the glue. Folks who have welded round without pulling and cleaning up first have had the glue contaminate the weld at times apparently.
I can't weld, I just make big holes so this is purely a regurgitation. Maybe others can chime in with actual thoughts smile

sportsandclassic

Original Poster:

3,774 posts

249 months

Sunday 21st August 2011
quotequote all
Hi,

You would really need to remove the pipes first as said the adhesive will come to the surface and contaminate the weld pool for sure. I am no alloy welder but lucky for me my dad is!

I can manage stainless and mild steels but am still learning ally welding.

Cast welding is the worst type too as it is full of impurities so added with glue and coolant residue it will not be the nicest material to weld, but sure it will be fine.

Have you seen the pipes ? Do they just have a few mm thick wall thickness ?

Mike

Dan7357

2,648 posts

239 months

Sunday 21st August 2011
quotequote all
So is it an engine out job?

Dan7357

2,648 posts

239 months

Sunday 21st August 2011
quotequote all
So is it an engine out job?

sportsandclassic

Original Poster:

3,774 posts

249 months

Sunday 21st August 2011
quotequote all
Hi,

As far as I can tell yes it is engine out.

Mike

fioran0

2,410 posts

203 months

Sunday 21st August 2011
quotequote all
Thanks. That's still a whole load better than me haha.

Yeah I've seen the pipes. The insert piece is thin walled. Lucky if it's even 2mm. The cast much thicker.
Any welds I've seen done have melted through the insert in places where the weld itself is. This is just filed down.

I believe there's as many cars just using JB Weld as there is full welds. This negates the need to remove inserts etc. Engine temp is approx 180F so well below JBs 500F capacity.


Slippydiff

16,503 posts

254 months

Sunday 21st August 2011
quotequote all
sportsandclassic said:
Hi,

You would really need to remove the pipes first as said the adhesive will come to the surface and contaminate the weld pool for sure. I am no alloy welder but lucky for me my dad is!

I can manage stainless and mild steels but am still learning ally welding.

Cast welding is the worst type too as it is full of impurities so added with glue and coolant residue it will not be the nicest material to weld, but sure it will be fine.

Have you seen the pipes ? Do they just have a few mm thick wall thickness ?

Mike
Thread with pics here :

http://www.pistonheads.com/gassing/topic.asp?h=0&a...

And another method of avoiding the issue :

http://www.6speedonline.com/forums/996-turbo-gt2/2...

996ttalot

1,931 posts

206 months

Monday 22nd August 2011
quotequote all
sportsandclassic said:
So after trawling the net for hours I have seen this is a worldwide fault, just not seen many reported cases in u.k....

I have decided to do my own set of pipes as a preventative measure.

Out of interest how many owners would want this mod doing ?

We have aluminium welding facilities on site.

Mike
Mike, we looked at this as well but in the end decided against it. We know of only one case in the UK. There are quite a lot of different solution to it and in the last three engine builds have decided not to do it.
Ken
p.s. I'll have to keep my fingers crossed now as that is probably the kiss of death