996 - new discs/pads - how long to run them in?
Discussion
Just go out and aggresively (sp) bed them in. There are various methods on the web.
I used to to do 3 or 4 60 down to 20 stops (medium braking), then 4 90 down to 40 and then a few 120 down to 30 runs.
In between each run DO NOT STOP and then drive for a mile or so to allow cooling.
Ideal roads are dual carrigways with round abouts at both ends.
Bingo.
I used to to do 3 or 4 60 down to 20 stops (medium braking), then 4 90 down to 40 and then a few 120 down to 30 runs.
In between each run DO NOT STOP and then drive for a mile or so to allow cooling.
Ideal roads are dual carrigways with round abouts at both ends.
Bingo.
I normally take it easy for the first 100 miles then over the next 150 miles start using them a little harder. The main thing is to get some heat cycles into them. By 250 miles of varied driving they should be good to go IMHO. Having said that mine tend not to last very long so I could be doing something wrong. My car is in for all four corners next week.
bull996 said:
Just go out and aggresively (sp) bed them in. There are various methods on the web.
I used to to do 3 or 4 60 down to 20 stops (medium braking), then 4 90 down to 40 and then a few 120 down to 30 runs.
In between each run DO NOT STOP and then drive for a mile or so to allow cooling.
Ideal roads are dual carrigways with round abouts at both ends.
Bingo.
For pads this is fine, for discs and pads less so as it doesn't allow decent bedding in/elimination of high spots between the disc and pads.I used to to do 3 or 4 60 down to 20 stops (medium braking), then 4 90 down to 40 and then a few 120 down to 30 runs.
In between each run DO NOT STOP and then drive for a mile or so to allow cooling.
Ideal roads are dual carrigways with round abouts at both ends.
Bingo.
Stick with Dazrens method and you won't go too far wrong.
Are you running six pot/350mm discs on the front Daz ?
dazren said:
Just the standard 330mm front system on the 996TT. Think the 350mm steel discs were introduced on the 996GT3 mk2.
Indeed they were, but there's nothing to stop you retro-fitting them (apart from any warranty issues that may arise . . .)Most likely explains why the standard stuff isn't lasting too long though !
I did a series of 10 times 60-10 mph stops, then driving without stopping or using the brakes (if possible) for several miles to allow to 'cool', then you repeat the process.
Expect some brake fade somewhere in the middle of each phase, and choose a suitable road and traffic conditions to ensure safety.
Here's a full description from someone who certainly knows what they are talking about.
Stoptech.
When a system has both new rotors and pads, there are two different objectives for bedding-in a performance brake system: heating up the brake rotors and pads in a prescribed manner, so as to transfer pad material evenly onto the rotors; and maturing the pad material, so that resins which are used to bind and form it are ‘cooked' out of the pad.
The first objective is achieved by performing a series of stops, so that the brake rotor and pad material are heated steadily to a temperature that promotes the transfer of pad material onto the brake rotor friction surface. There is one pitfall in this process, however, which must be avoided. The rotor and, therefore, the vehicle should not be brought to a complete stop, with the brakes still applied, as this risks the non-uniform transfer of pad material onto the friction surface.
The second objective of the bedding-in process is achieved by performing another set of stops, in order to mature the pad itself. This ensures that resins which are used to bind and form the pad material are ‘cooked' out of the pad, at the point where the pad meets the rotor's friction surface.
http://www.stoptech.com/tech_info/wp_bedinperforma...
Expect some brake fade somewhere in the middle of each phase, and choose a suitable road and traffic conditions to ensure safety.
Here's a full description from someone who certainly knows what they are talking about.
Stoptech.
When a system has both new rotors and pads, there are two different objectives for bedding-in a performance brake system: heating up the brake rotors and pads in a prescribed manner, so as to transfer pad material evenly onto the rotors; and maturing the pad material, so that resins which are used to bind and form it are ‘cooked' out of the pad.
The first objective is achieved by performing a series of stops, so that the brake rotor and pad material are heated steadily to a temperature that promotes the transfer of pad material onto the brake rotor friction surface. There is one pitfall in this process, however, which must be avoided. The rotor and, therefore, the vehicle should not be brought to a complete stop, with the brakes still applied, as this risks the non-uniform transfer of pad material onto the friction surface.
The second objective of the bedding-in process is achieved by performing another set of stops, in order to mature the pad itself. This ensures that resins which are used to bind and form the pad material are ‘cooked' out of the pad, at the point where the pad meets the rotor's friction surface.
http://www.stoptech.com/tech_info/wp_bedinperforma...
Gassing Station | Porsche General | Top of Page | What's New | My Stuff





