997.1 GT3 fitting lower gear ratios?
Discussion
Re-gearing is a very personal thing.
Getting the car to "feel" the way YOU want it to, is definatelty the way to go.
I have re-geared my bike, instead of 178mph top end (which I will never use) its now awesome in mid range and will probably ONLY do 160 now, which is fine for me - granted its much easier to re-gear a bike than a car, but its all relative!
Go for it.
Getting the car to "feel" the way YOU want it to, is definatelty the way to go.
I have re-geared my bike, instead of 178mph top end (which I will never use) its now awesome in mid range and will probably ONLY do 160 now, which is fine for me - granted its much easier to re-gear a bike than a car, but its all relative!
Go for it.
You will see the car in this advert has had a cup final drive installed. The car is at JZM and they said they did it. I would give them a call or any of the other usual suspects.
http://www.pistonheads.com/sales/2891730.htm
http://www.pistonheads.com/sales/2891730.htm
This is definitely possible.
The 997.2 Gt3 RS with 450BHP has shorter gearing it's another reason why it gets too 100mph so fast so that's definetely an option. The other is to use C2S gearing though this could be what the 997.2 RS uses?
The 997.2 Gt3 RS with 450BHP has shorter gearing it's another reason why it gets too 100mph so fast so that's definetely an option. The other is to use C2S gearing though this could be what the 997.2 RS uses?
Edited by Gibbo205 on Wednesday 21st September 21:52
changing the R&P as mentioned here is the common way to go for shortening the gears.
the 4:1 R&P increases acceleration tremendously but at the expense of top end speed and 1st gear. 2nd seems to become a weird interim gear too, neither a true 1st nor a decent 2nd. also changing the R&P doesnt adjust the spacing between the gears.
for regular use though the regular gear spacing from 3-6 combined with the R&P seems to suit most people from what i hear so long as you can live with the shortened 1st and 2nd. the cups use a long 1st gear to work with the 4:1 drive.
as mentioned, the cup R&P from porsche motorsport is an 8:32. the guard one is i believe actually 8:33, the thinking being as also mentioned that you get extended wear as the teeth meet with different teeth each time round.
regearing the GT3 gearbox can also be done pretty easily so long as you only want to change gears 3-6. you are stuck with 1st and 2nd from stock unless you change the main shaft to the cup one, at which point you will be in for more than your whole gearbox in parts if you are also changing 3-6 even without picking up the cups steel syncros. the upside of this is you keep a workable 1st and 2nd and can select a 3-6 spacing and ratio that fits with your use.
the ideal is a short R&P and a full regear to compliment but as mentioned you are talking huge money by the time you are at this level.
you really need to think what you want from the car and this should point you in the right direction for a solution. for the OP is sounds like the R&P would be the way to go.
hopefully mike will be along in a bit to tell me im talking crap and give you proper details as this is his area
the 4:1 R&P increases acceleration tremendously but at the expense of top end speed and 1st gear. 2nd seems to become a weird interim gear too, neither a true 1st nor a decent 2nd. also changing the R&P doesnt adjust the spacing between the gears.
for regular use though the regular gear spacing from 3-6 combined with the R&P seems to suit most people from what i hear so long as you can live with the shortened 1st and 2nd. the cups use a long 1st gear to work with the 4:1 drive.
as mentioned, the cup R&P from porsche motorsport is an 8:32. the guard one is i believe actually 8:33, the thinking being as also mentioned that you get extended wear as the teeth meet with different teeth each time round.
regearing the GT3 gearbox can also be done pretty easily so long as you only want to change gears 3-6. you are stuck with 1st and 2nd from stock unless you change the main shaft to the cup one, at which point you will be in for more than your whole gearbox in parts if you are also changing 3-6 even without picking up the cups steel syncros. the upside of this is you keep a workable 1st and 2nd and can select a 3-6 spacing and ratio that fits with your use.
the ideal is a short R&P and a full regear to compliment but as mentioned you are talking huge money by the time you are at this level.
you really need to think what you want from the car and this should point you in the right direction for a solution. for the OP is sounds like the R&P would be the way to go.
hopefully mike will be along in a bit to tell me im talking crap and give you proper details as this is his area

Edited by fioran0 on Wednesday 21st September 23:09
I have the short cup ratio fitted to my RS which I use mainly on track.
Car feels like it has 30-40 bhp more (subjectively) - surprisingly, it was only worth a couple of tenth on most tracks. It now runs into the limiter at about 300 km/h. The only real downside is that on motorway journeys the car obviously revs a lot higher now. On German motorways this means I am now limited to about 230 km/h (6.200 rpm) as the engine wont like staying at the otherwise very high revs at higher speeds.
Not really a problem in the uk though and is a tweak that is probably more cost effective than any other (power wise).
Regards,
Felix
Car feels like it has 30-40 bhp more (subjectively) - surprisingly, it was only worth a couple of tenth on most tracks. It now runs into the limiter at about 300 km/h. The only real downside is that on motorway journeys the car obviously revs a lot higher now. On German motorways this means I am now limited to about 230 km/h (6.200 rpm) as the engine wont like staying at the otherwise very high revs at higher speeds.
Not really a problem in the uk though and is a tweak that is probably more cost effective than any other (power wise).
Regards,
Felix
FiaronO, I'm looking at fitting the 8:32 CWP to my 993 RSR Race Car but was worried that this would make 1st gear useless, and possibly 2nd too. You mention cups having higher 1st gears, do you know if I could get one of these for my RSR, and where, Porsche Motorsport ? I assume you refer to 997 Cups but AFAIK the 993 is essentially the same box. Is the sequential box different internals to the GT3RS ?
majordad,
it was the 996 cup i was referring to specifically above. the 996 cup gearbox differs quite a bit inside from the street gearboxes but the main difference in relation to this subject is that only 1st gear is fixed to the main shaft.
this lets you change all the gears from 2-6 to suit your needs. on the street car 1 and 2 and fixed which means you cant change them without buying a main shaft from porsche motorsport.
last time i checked a main shaft/1st gear was £2500 and 2nd was £1500 versus £950 for the shaft with 1st and 2nd gears for the street car.
ive no idea ref the 993 trans. i assume much of the same will apply but with everything the devil is in the details and on this ive simply no idea. ive only ran 996 and 997. fwiw many of the cup gear part numbers are 993 numbers so probably carry over from the 993 race program.
do you know what ratios your box uses for the gears at the moment, this might give a better feel for how an 8:32 will impact it. i think some of the G50 boxes had a 3.15 1st gear too so this would be just fine with the R&P change.
i thought the RSR used an 8:32 final drive from factory?. are you building an RSR project? if so it might be that you can pull together gearsets or parts from various sources (or indeed another gearbox) to let you change everything to get an RSR type box with a range of ratios that all work well if thats what you are after.
sorry i couldnt give you better info. maybe mike (sportsclassic) will know. if not give california motorsports an email. they will give you a ton of info on options and what you can do etc. they might also have leads on parts.
it was the 996 cup i was referring to specifically above. the 996 cup gearbox differs quite a bit inside from the street gearboxes but the main difference in relation to this subject is that only 1st gear is fixed to the main shaft.
this lets you change all the gears from 2-6 to suit your needs. on the street car 1 and 2 and fixed which means you cant change them without buying a main shaft from porsche motorsport.
last time i checked a main shaft/1st gear was £2500 and 2nd was £1500 versus £950 for the shaft with 1st and 2nd gears for the street car.
ive no idea ref the 993 trans. i assume much of the same will apply but with everything the devil is in the details and on this ive simply no idea. ive only ran 996 and 997. fwiw many of the cup gear part numbers are 993 numbers so probably carry over from the 993 race program.
do you know what ratios your box uses for the gears at the moment, this might give a better feel for how an 8:32 will impact it. i think some of the G50 boxes had a 3.15 1st gear too so this would be just fine with the R&P change.
i thought the RSR used an 8:32 final drive from factory?. are you building an RSR project? if so it might be that you can pull together gearsets or parts from various sources (or indeed another gearbox) to let you change everything to get an RSR type box with a range of ratios that all work well if thats what you are after.
sorry i couldnt give you better info. maybe mike (sportsclassic) will know. if not give california motorsports an email. they will give you a ton of info on options and what you can do etc. they might also have leads on parts.
Edited by fioran0 on Thursday 22 September 13:06
noneedtolift said:
I have the short cup ratio fitted to my RS which I use mainly on track.
Car feels like it has 30-40 bhp more (subjectively) - surprisingly, it was only worth a couple of tenth on most tracks. It now runs into the limiter at about 300 km/h. The only real downside is that on motorway journeys the car obviously revs a lot higher now. On German motorways this means I am now limited to about 230 km/h (6.200 rpm) as the engine wont like staying at the otherwise very high revs at higher speeds.
Not really a problem in the uk though and is a tweak that is probably more cost effective than any other (power wise).
Regards,
Felix
Why not get a taller 6th put in like the 7.2RS? I was chatting to Steve at JZM about it the other day and he reckons it would be a straightforward job. Given the effect on touring range of the shorter final drive it would probably pay for itself in fuel in the medium term and for all the use that 6th gets on track it ought not cost any kind of performance hit...Car feels like it has 30-40 bhp more (subjectively) - surprisingly, it was only worth a couple of tenth on most tracks. It now runs into the limiter at about 300 km/h. The only real downside is that on motorway journeys the car obviously revs a lot higher now. On German motorways this means I am now limited to about 230 km/h (6.200 rpm) as the engine wont like staying at the otherwise very high revs at higher speeds.
Not really a problem in the uk though and is a tweak that is probably more cost effective than any other (power wise).
Regards,
Felix
Gassing Station | Porsche General | Top of Page | What's New | My Stuff


