Door opening when cold - sticking windows
Door opening when cold - sticking windows
Author
Discussion

ScienceTeacher

Original Poster:

408 posts

215 months

Monday 21st January 2013
quotequote all
My 996 like some other Porsche models has frameless windows. The window needs to retract a little to open the door, which it does when you tug the handle. Once or twice I have needed to open the car when it has frosted and the window does not retract leaving me in a nasty position with the door half open and the window holding it shut.
My car is in good condition. I apply rubber protector to all the rubber and it is supple and not sticky. I use the windows regularly and they work fine. It seems to me this a problem that would afflict any frameless window car including the 991. One has to question how they can do the winter testing in Sweden when they can't open the door.
I now put a rug over the driver's side covering the window completely and it seems to work, but probably won’t when it's really bitter as it freezes inside the door I suspect. I use warm screenwash before I try to open the car all around the window. When I enter the car I start it and run the heaters for 10 minutes before trying the windows. Some cars in the States have automatic start / heating facilities. This seems extreme.
Clearly one does not always have a cover or heated garage. What do people do?



Trev450

6,757 posts

202 months

Monday 21st January 2013
quotequote all
Common problem. I think most people, myself included, use either de-icer or warm water.

monthefish

20,467 posts

261 months

Monday 21st January 2013
quotequote all
The wife's hairdryer.

(I believe some de-icer sprays are bad for rubber seals/paintwork)

trashbat

6,307 posts

183 months

Monday 21st January 2013
quotequote all
What is 'rubber protector'? No clue about your specific car, but I avoid doors and windows sticking using silicone spray. Be a bit careful with it as it will cause windows to smear.

Magic919

14,535 posts

231 months

Monday 21st January 2013
quotequote all
Gummi pflege is the stuff I use.

Kenzle

154 posts

199 months

Monday 21st January 2013
quotequote all
A credit card slid between the rubber and glass on the bottom edge usually does the trick.

Mr Ping

262 posts

166 months

Monday 21st January 2013
quotequote all
Ive been using the credit card trick since reading it on this forum! works a treat!

sootyvrs

364 posts

172 months

Monday 21st January 2013
quotequote all
Kenzle said:
A credit card slid between the rubber and glass on the bottom edge usually does the trick.
Just make sure you have a large credit limit before using it on your Porsche wink

MogulBoy

3,066 posts

253 months

Monday 21st January 2013
quotequote all
As above, it is ice forming between the inner surface of the horizontal door seal and the outer surface of the side window glass that you are up against. The credit card solution works here but adding heat may be necessary...

I have assumed that new or nearly new seals have some sort of nano technology / water repellant qualities on the inner (flocked?) surface that keeps water away. After a few years, these properties are long gone and no amount of treating the visible outer surface of the door seal - the bit that doesn't come into contact with anything - is going to help you here. In a word, you are (it ryhmes with) flocked.

K-Cee

238 posts

218 months

Monday 21st January 2013
quotequote all
Try some "Vaseline" around the rubber seals, that should do it .

chiark

118 posts

180 months

Monday 21st January 2013
quotequote all
Prevention: use silicone spray on the seal. That should/might stop it sticking in the first place.

MogulBoy

3,066 posts

253 months

Monday 21st January 2013
quotequote all

Trev450

6,757 posts

202 months

Monday 21st January 2013
quotequote all
chiark said:
Prevention: use silicone spray on the seal. That should/might stop it sticking in the first place.
I've tried this and all it achieves is to stop the creaking noise you get when the seal is dry. Oh and it leaves smears on the glass.

Edited by Trev450 on Monday 21st January 16:14

monthefish

20,467 posts

261 months

Monday 21st January 2013
quotequote all
MogulBoy said:
Who? Why?

trashbat

6,307 posts

183 months

Monday 21st January 2013
quotequote all
MogulBoy said:
As above, it is ice forming between the inner surface of the horizontal door seal and the outer surface of the side window glass that you are up against. The credit card solution works here but adding heat may be necessary...

I have assumed that new or nearly new seals have some sort of nano technology / water repellant qualities on the inner (flocked?) surface that keeps water away. After a few years, these properties are long gone and no amount of treating the visible outer surface of the door seal - the bit that doesn't come into contact with anything - is going to help you here. In a word, you are (it ryhmes with) flocked.
So why don't you just spray some in there?

0 to 60

21 posts

186 months

Monday 21st January 2013
quotequote all
Isn't the seal replaceable?

Rockster

1,515 posts

190 months

Monday 21st January 2013
quotequote all
ScienceTeacher said:
My 996 like some other Porsche models has frameless windows. The window needs to retract a little to open the door, which it does when you tug the handle. Once or twice I have needed to open the car when it has frosted and the window does not retract leaving me in a nasty position with the door half open and the window holding it shut.
My car is in good condition. I apply rubber protector to all the rubber and it is supple and not sticky. I use the windows regularly and they work fine. It seems to me this a problem that would afflict any frameless window car including the 991. One has to question how they can do the winter testing in Sweden when they can't open the door.
I now put a rug over the driver's side covering the window completely and it seems to work, but probably won’t when it's really bitter as it freezes inside the door I suspect. I use warm screenwash before I try to open the car all around the window. When I enter the car I start it and run the heaters for 10 minutes before trying the windows. Some cars in the States have automatic start / heating facilities. This seems extreme.
Clearly one does not always have a cover or heated garage. What do people do?
Had this problem when leaving my Boxster out in the cold weather sometimes during a snow storm.


While the window does not drop the door can be opened though the top edge of the window rubs against the top rail.

While the noise doesn't have a pleasant sound I open the door easy and so far there's been harm.

Before I close the door though from inside the car I use the lower button and some gentle downward pressure on the glass to get it to go down. I then use the window buttons to make sure the window moves freely then just to be sure lower the window and close the door.

Once closed I then raise the window.

If I do not drive the car long enough that the snow/ice on the roof can melt and the top dry out, when I park the car the heat from the cabin will continue to melt this and water will run down over the glass. This can have the window freeze again so just because one frees the windows up one time doesn't mean he is done for the day.

Also, depending upon the weather conditions the glass and rubber seal may stick/freeze together without having inches of snow fall. So I just learned to be aware of this and take opening the door easy.

Oh, I tried Gummi Plfedge but it didn't seem to make a difference.

What I found helped some was to be sure the portion of the window that contacts the rubber seal is clean clean clean. This goes for the rubber seal as well. Use no harsh detergents/cleaners or petro based cleaners.

Also, to a less degree the sheet metal door jam can freeze to the door seal so you have to keep that in mind as you open the door.