Please help!!!! 944T rough engine
Please help!!!! 944T rough engine
Author
Discussion

Tony Beckwith

Original Poster:

54 posts

249 months

Thursday 11th October 2007
quotequote all
Hi all

I'm looking for some help/advice on my 86 944T please!!!

The engine has started running rough, mini backfires sometimes on hard acceleration and a general lack of the typical urge...

Just added fresh fuel (in case it was diluted petrol) but no change...

Any of you experts out there any pointers for me? DME relay/fuel pump? Spark plug-related?

Any help really appreciated - big trip due saturday - yikes!!

Tony B.


Pope

2,653 posts

278 months

Thursday 11th October 2007
quotequote all
The three way diverter / boost control valve under the manifold at the rear of the engine is usually to blame for any accelerative issues.

Does the misfiring / backfiring occur after an initially sprightly bit of acceleration??
If so, the turbo system may be reaching the overboost threshold and causing the management system to back off the timing / boost.

Check the valve for any leaks / breakage of the three branches, plug connections etc..

Tony Beckwith

Original Poster:

54 posts

249 months

Thursday 11th October 2007
quotequote all
Thanks for this prompt reply Pope

Yes, just a couple of pops/misfires under initial 1st/2nd acceleration...would that explain general poor engine running, though?

All ideas very much appreciated and welcome!

Thanks again

Tony.

IMI A

9,997 posts

232 months

Thursday 11th October 2007
quotequote all
could just be a loose hose somewhere or air leak. pain in the butt to find

Pope

2,653 posts

278 months

Tuesday 6th November 2007
quotequote all
Did you track the problem down Tony?

Tony Beckwith

Original Poster:

54 posts

249 months

Tuesday 6th November 2007
quotequote all
What a superb forum this is - you guys come and find me genuinely to see what the solution is - fantastic! Thanks Pope.

My local mechanic adjusted the air/fuel ratio, which seemed to settle it...however, the cooling fan comes on a lot more often than it ever used to...

Then mechanic said I may need a new air flow meter...does that make sense to you?

Many thanks again

Tony.

studog

268 posts

288 months

Tuesday 6th November 2007
quotequote all
Have a look on the Clark's garage website for a how to on refurbing your airflow meter. I did it on my sadly departed S2 and it worked a treat. Only took about half an hour and made all the difference.

Tony Beckwith

Original Poster:

54 posts

249 months

Tuesday 6th November 2007
quotequote all
Great advice - many thanks...better route initially than a brand new one at around £350 (and even a refurb'd one from Porscheapart at £90..............!)
Thanks again
Tony.

hartech

1,929 posts

248 months

Tuesday 6th November 2007
quotequote all
I won't say why yet - in case it proves to be scare mongering - but - what level does the expansion tank show after a few days of running the engine after topping it up to the higher level?

Will explain later.

Baz

Tony Beckwith

Original Poster:

54 posts

249 months

Tuesday 6th November 2007
quotequote all
Not sure Baz...are you sensing a leak, causing overheating (temp > 90deg?) and the fan to cut in a lot?

hartech

1,929 posts

248 months

Tuesday 6th November 2007
quotequote all
Tony - top it up to the top level, allow to go completely cool (say next day), go for a run, let it cool down again and check the level and let me know - I'll tell you why then.

Baz

Tony Beckwith

Original Poster:

54 posts

249 months

Tuesday 6th November 2007
quotequote all
Intriguing - will do Baz ... !

Tony Beckwith

Original Poster:

54 posts

249 months

Monday 12th November 2007
quotequote all
Well, I don't see any change...no drop in the coolant level anyway...

The fan seems to cut in correctly around 90deg and then cut back out around 70deg...trouble is it's now cutting in after only a couple of mins idle or light traffic...

Guess I'll have to take it back to the local mech...

Tony

hartech

1,929 posts

248 months

Monday 12th November 2007
quotequote all
Ok, if it was down I would suggest the head gasket failing as this blows some coolant out and restricts coolant flow but if the level is Ok it is probably not that. If it had been this it would explain both problems - the misfire and the fluctuating temperature, but if the coolant level stays high - it is probably not that.

If it was a 2.7, S2 or 968 I would suggest the impellor coming lose at the inside of the water pump, but a 2.5 turbo should have a different impellor that I have never seen come lose (although I have seen the bigger pump with the plastic impellor - fitted to the wrong engines).

If the cam belt is very slack or it has an sprung adjuster I would suggest it may be at maximum extension or i have even seen a water pump bearing getting stiff and causing the belt to skip - but this doesn't explain the misfire.

You could have a dicky thermostat - but again this only explains the temperature problem.

The king ht lead can short out internally under load (so if the misfire is under load it could be that) or the boost could be too high as previously and correctly diagnosed and described. There are many reasons for this - not the least an air leak, pipes cracked, lose circular pipe end fitted in the manifold etc.

Sorry my "master plan solution" didn't reveal the answer this time but good luck with it.

Baz


Tony Beckwith

Original Poster:

54 posts

249 months

Monday 12th November 2007
quotequote all
Thanks for this great attention Baz - appreciated!

The lumpy idle, heavy acceleration and occasional misfire don't happen any more as the local mech adjusted the 'air ratio'....(?). It's just the fan cutting in so much now...

On the other hand, if the fan is doing its job...can i run with it?

Thanks again

Tony.

UK952

769 posts

290 months

Tuesday 13th November 2007
quotequote all
When your mech adjusted the AFR he may have been compensating for a leak - there are lots of pipes that could be leaking boost, reckon its worth a good look around them,
Tony