996 GT2 BIGGER TURBOS......
Discussion
Good morning all, considering going the to the next level with my GT2, currently running Miltek pipe and headers (100 cell) DMS remap etc. Already have the uprated clutch fitted. From what I have read 620/650bhp seems to be achievable and reliable (as it can be) Anybody got any real world knowledge of the companies in the UK that can do this? 

My car recently underwent a DMS conversion,
The outcome was 608.5bhp and 590 lbft,
It perfromed a 202mph run at brunters recently using k24/26 turbo's .
The car is unreal,
It eats 600cc motorbikes for breakfast and up against a gsxr 1000 recently from 40 -150 the bike only managed to creep past my front bumper,
Had the road, er I mean test track been longer im sure i would have caught it and gone past it.
DMS performed most of the work,
Speak to rob
The outcome was 608.5bhp and 590 lbft,
It perfromed a 202mph run at brunters recently using k24/26 turbo's .
The car is unreal,
It eats 600cc motorbikes for breakfast and up against a gsxr 1000 recently from 40 -150 the bike only managed to creep past my front bumper,
Had the road, er I mean test track been longer im sure i would have caught it and gone past it.
DMS performed most of the work,
Speak to rob
SpeedFreakDave said:
ineedagallardo....i like the sound of that.....don't think I have seen you at brunters......was it an expensive upgrade? did you change the conrods?
I was there at the last outing and will be attending the next in november, Hopfully ill see you there
.The upgrade wasn't that expensive in terms of how much other companys charge for a similiar power figure.
I did some research on the conrod issue and came to the conclusion that the standard internals were good for at least 650 bhp so we stayed well within the envelope.
We did however change quite a few other components along with the turbos to gain the 608 figure.
SpeedFreakDave said:
ineedagallardo....i like the sound of that.....don't think I have seen you at brunters......was it an expensive upgrade? did you change the conrods?
I would say you would have to do it putting down this kind of power, the car might be fine running on stock rods, might run for a few years, might run for few minutes, the whole point is your getting into the danger zone.It like, how long can you stay on the redline, if you get what i'm saying!
996TT_STEVO said:
SpeedFreakDave said:
ineedagallardo....i like the sound of that.....don't think I have seen you at brunters......was it an expensive upgrade? did you change the conrods?
I would say you would have to do it putting down this kind of power, the car might be fine running on stock rods, might run for a few years, might run for few minutes, the whole point is your getting into the danger zone.It like, how long can you stay on the redline, if you get what i'm saying!

I did discuse this with rob when he remapped the car.
The problem with most turbo maps are you get a big power spike at 4k then the power drops off,
The problem with this is that your trying to make something thats moving slowly move quickly too fast which is normlly whay the rods bend.
With the map on my car the graph (which can be seen in my profile) looks more like a NA car as opposed to a turbo with a smooth power curve,
This is visable in car as the boost hits 1 Bar, then 1.1. 1.2 before peaking at 1.3 @ 6200rpm and holding to the red line.
Best thing to do.... Strip the engine down to bare crank cases, then have the crank cases gas flowed to help bottom end breathing(this in itself increases horsepower), stick in some carrilo rods to handle the boost, have the heads worked including valves and inlet stacks, increase the air intake to 100mm or so, use sensible uprated manifolds, kkk 24/26 turbos, nice exhaust and have someone who really knows what they are doing to map it. There you have it..650bhp reliable!!! Dont believe that a stock motor will handle all of this, not for long anyway. Do it properly!!!
Cheeko said:
Best thing to do.... Strip the engine down to bare crank cases, then have the crank cases gas flowed to help bottom end breathing(this in itself increases horsepower), stick in some carrilo rods to handle the boost, have the heads worked including valves and inlet stacks, increase the air intake to 100mm or so, use sensible uprated manifolds, kkk 24/26 turbos, nice exhaust and have someone who really knows what they are doing to map it. There you have it..650bhp reliable!!! Dont believe that a stock motor will handle all of this, not for long anyway. Do it properly!!!
Motor is bullit proof, only the rods are like butter, this is fact!Still your on the right track to gain a bit more reliablity at these levels
Edited by 996TT_STEVO on Sunday 14th October 00:25
Hi There
I have done all this work to a GT2 04 car and we did a run before and after the upgrade...
We had 474BHP before the upgrade and 540bhp after,there was no more to be had from it with modified K25 turbos,fuel pressure regulator,Tubi sports exhaust,equal length exhaust manifolds and ecu re-map on rolling road all equipment supplied by DMS...fitted by us and mapped by DMS.
The car seemed to be breaking traction at the rolling road but i can't see there being another 100bhp there.
If i were to do another one i would go a different route and add something different to the car.
Mike
sports and classic ltd
I have done all this work to a GT2 04 car and we did a run before and after the upgrade...
We had 474BHP before the upgrade and 540bhp after,there was no more to be had from it with modified K25 turbos,fuel pressure regulator,Tubi sports exhaust,equal length exhaust manifolds and ecu re-map on rolling road all equipment supplied by DMS...fitted by us and mapped by DMS.
The car seemed to be breaking traction at the rolling road but i can't see there being another 100bhp there.
If i were to do another one i would go a different route and add something different to the car.
Mike
sports and classic ltd
Gassing Station | Porsche General | Top of Page | What's New | My Stuff




