Immobiliser Problems.................
Immobiliser Problems.................
Author
Discussion

markys

Original Poster:

620 posts

286 months

Saturday 16th April 2005
quotequote all
Put the plastic key in and the red light carrys on flashing, any ideas ???

gazzab

21,627 posts

311 months

Saturday 16th April 2005
quotequote all
I never bothered with the red plasticy thing. Just pressed the key fob (with go button already pressed - I think), then fuel pump etc into life, start her up and away....

markys

Original Poster:

620 posts

286 months

Saturday 16th April 2005
quotequote all
Thats what I normaly do but it wont disable.

markys

Original Poster:

620 posts

286 months

Saturday 16th April 2005
quotequote all
The symptoms are, if i use either the key or the fob the light pauses for a moment and then continues to flash, wipers, lights etc continue to function normaly but no power to the starter and no MIL beep ! I have disconected the battery for 5 minutes but that has not helped. Edited to say fuel pump does not prime either.

Please Help, its due in for a service next Saturday and at this rate it will be on the back of a low loader.

>> Edited by markys on Saturday 16th April 17:49

satman

2,455 posts

275 months

Saturday 16th April 2005
quotequote all
Is the alarm arming and setting as per norm?..ie indicators flash 3 times and rear window led flashes...

markys

Original Poster:

620 posts

286 months

Saturday 16th April 2005
quotequote all
Yes, the alarm seems fine.

markys

Original Poster:

620 posts

286 months

Tuesday 19th April 2005
quotequote all
Any ideas ????

Extra 300 Driver

5,282 posts

275 months

Tuesday 19th April 2005
quotequote all
Have you reset the crash switch? Other than that I dont have a clue. Have you tried the experts?

>> Edited by Extra 300 Driver on Tuesday 19th April 12:50

markys

Original Poster:

620 posts

286 months

Tuesday 19th April 2005
quotequote all
Have tired the crash switch.

Slimm

4 posts

258 months

Tuesday 19th April 2005
quotequote all
I have had lots of problems with my own Cerbera but not quite like this though. Have you spoken to your local TVRCC Regional Organiser? They have helped me in the past with my own problems as they have access to a wealth of knowledge and can in most cases offer some helpful tips.

Steve_T

6,356 posts

301 months

Tuesday 19th April 2005
quotequote all
My recommendation would be Karl Baker. Lovely bloke and knows his stuff. I had a dead alarm plipper and decided the best option would be to replace both, before the second one died too. His contact details are on www.tvruk.tv

Cheers,

Steve.

zippee

14,121 posts

263 months

Tuesday 19th April 2005
quotequote all
Steve_T said:
My recommendation would be Karl Baker. Lovely bloke and knows his stuff. I had a dead alarm plipper and decided the best option would be to replace both, before the second one died too. His contact details are on www.tvruk.tv

Cheers,

Steve.

Seconded - Used him last week for a replacement immobiliser. Out of all the alarm specialists I tried he was the only one who could do this, thus saving me a fortune compared to the next best advise of ripping it all out and replacing the entire system.
Top bloke, very helpful and really knows his stuff when it comes to TVR alarms etc.

apprentice

1,219 posts

289 months

Thursday 21st April 2005
quotequote all
Hi Mark,

Sorted?

Endorse the advice of Steve and Tony - speak to Carl Baker. Just be aware Carl takes a break shortly - so contact him soon, if you haven't done so already.

apprentice

markys

Original Poster:

620 posts

286 months

Thursday 21st April 2005
quotequote all
apprentice said:
Hi Mark,

Sorted?

Endorse the advice of Steve and Tony - speak to Carl Baker. Just be aware Carl takes a break shortly - so contact him soon, if you haven't done so already.

apprentice


Its been low loaded upto Peninsular think they know of Carl. Same that AB warranty has run out now !!