How Much Clutch Fluid Required to Bleed Clutch??
How Much Clutch Fluid Required to Bleed Clutch??
Author
Discussion

Braddy

Original Poster:

81 posts

269 months

Tuesday 24th May 2005
quotequote all
Hi all, I've been having a problem with my clutch. About 6 months ago it went down to the last inch. I managed to get it to SFR to get it fixed. Shane had a look but after topping up the fluid couldn't see any leaks. It held for ages, but the same thing happened a couple of weeks ago. Again Shane topped it up used it for a few days and couldn't see a problem. I used it for a week and all was fine till Sunday when the clutch went completely. It is now just swinging away in the wind :-( I'm gonna try to bleed it tonight to see if I can get it going again.
Can I just confirm:
a) If it's a Slave problem I should have fluid under car?
b) If it's a Master problem I should have a damp footwell?
Cause upto now I'm buggered if I can see where it keeps going!

Extra 300 Driver

5,282 posts

275 months

Tuesday 24th May 2005
quotequote all
If its your master cylinder you will have fluid all over your shoes, pedal and mat. If it’s the slave then you ‘may’ have some fluid under the car but not always. There is only a small hole in bell housing to allow any fluid to escape, this could be blocked.

In your reservoir do you have any deposits of black rubber? You will find them on the cap.

If it is taking a lot of fluid then there is something wrong. If its your slave seals only use the ones from Joolz.

Braddy

Original Poster:

81 posts

269 months

Tuesday 24th May 2005
quotequote all
Cheers for that - Do you know how much fluid it takes when it's empty. I need to buy it this afternoon and don't want to buy too little. I've not got the manual with me to check

Extra 300 Driver

5,282 posts

275 months

Tuesday 24th May 2005
quotequote all
Braddy said:
Cheers for that - Do you know how much fluid it takes when it's empty. I need to buy it this afternoon and don't want to buy too little. I've not got the manual with me to check


Buy at least a litre, and make sure its 5.1

TooTall Paul

938 posts

276 months

Tuesday 24th May 2005
quotequote all
It takes a very small amount, when my master cylinder went there were no signs of leaks anywhere !!

Extra 300 Driver

5,282 posts

275 months

Tuesday 24th May 2005
quotequote all
TooTall Paul said:
It takes a very small amount, when my master cylinder went there were no signs of leaks anywhere !!


So where did the fluid go?

vinny73

221 posts

258 months

Tuesday 24th May 2005
quotequote all
My slave has just been fixed, Joospeeds seals, APM fitted.
There was a large patch of fluid under my car on the garage floor, roughly inbetween the driver/passenger footwells just behind the wheels if you imagine looking from the side. No fluid inside the car.
If you are having to rebleed, surely its best to get the car in and sorted somewhere. I was "lucky" enough for it to die on my driveway, if I was out and about, wouldnt have been too happy if I was left stranded.






>> Edited by vinny73 on Tuesday 24th May 14:37

Braddy

Original Poster:

81 posts

269 months

Tuesday 24th May 2005
quotequote all
I'm hoping to get it going enough to get it into the garage - or atleast 3/4 mile from my house so that the AA will take me to the garage of my choice!!
Hopefully if I leave it on my drive for a few days first I might find where the fluid is coming out.

TooTall Paul

938 posts

276 months

Tuesday 24th May 2005
quotequote all
Extra 300 Driver said:

TooTall Paul said:
It takes a very small amount, when my master cylinder went there were no signs of leaks anywhere !!



So where did the fluid go?


You tell me ???

joospeed

4,473 posts

307 months

Tuesday 24th May 2005
quotequote all
The fluid can often fill the gap between the back of the bellhousing and the gearbox .. when you pull them apart half a litre of fluid spalshes all over your feet.

Braddy

Original Poster:

81 posts

269 months

Wednesday 25th May 2005
quotequote all
Cheers Joospeed - I'm guessing you've had damp feet a few times.
It would appear this isn't my problem now. I took the cap off last night and it's full to the top. I opened the bleed valve but as there's no resistance on the clutch, pumping it did nothing.
Fraid I'm resorting to the AA now!!

Extra 300 Driver

5,282 posts

275 months

Wednesday 25th May 2005
quotequote all
Sounds like your fingers have gone. I guess it still could be one of the seals in the master, just not producing pressure.