Cerbera ECU needed

[Twin pipe]

1995 4.2 ECU and associated electrical parts in passenger footwell, ignition booster and heater control, with a section of loom as well.

[mars]

Well, I have an ECU I keep meaning to stick on Ebay but none of the other parts. It's from a 4.5 and has been adjusted to suit a 4.5RR. I'm sure it could be equally adjusted for a 4.2. Keep it in mind if you get stuck for one with the associated components requested.

[trackcar]

have you bought the fire damaged 4.2 in the classifieds then twin pipe? bargain if you have!

[bodger bedge]

Hi
I have a spare 4.2 MBE ECU that I was considering selling. Make me an offer. I can be contacted on [e-mail]. I might have some other parts...I will look them out.

[Twin pipe]

Phil, i cannot seem to email you can you email me on... [e-mail] cheers

[Twin pipe]

Yes, the blue one. Gonna need a lot of help on this one chaps, might be too much for me to sort myself.

[Twin pipe]

I now have most electrical parts , all i need is the wiring loom from ECU to bulkhead connector. Can anyone help ? otherwise i am faced with trying to connect/trace 35 wires into my engine loom !!

[Twin pipe]

Any wiring looms out there ? early 1995/6 ECU to bulkhead connector ? or can anyone decipher the 35 pin connector wire positions. I have the online wiring diagrame to help but it doesnt show what wires go to which pin on the connector..

[byker28i]

www.pbase.com/byker28i/tvr&page=all

About half way down I photographed all my boxes connectors for someone else.

Any good?

[Twin pipe]

I,m selling her, its too much for me to do on my own. any enquiries email me or see eb#y listing.

[julian64]

I am looking for a spare MBE ECU, what does everyone want to sell theirs for?

[Twin pipe]

Just need loom now, the ECU to bulkhead section with the metal plug in the bulkhead.

Edited by Twin pipe on Thursday 24th May 21:11

[ridds]

http://cgi.ebay.co.uk/1996-TVR-CERBERA-BLUE_W0QQit...

Given up already?

[Twin pipe]

Dont know, see how it goes on there , sunk a fair few quid in already , may give her another try next week when i get the time and if i still have her.... any looms out there ? i did say loom not loon !

[Toadusmodus]

Graham, have a look at http://www.pistonheads.com/gassing/topic.asp?h=0&a...

I got the whole thing from http://www.douglasvalley.co.uk/. My car has the connection under the expansion tank in the engine compartment, but I have bought the single piece loom. Not cheap though! Give them a call, but I may have a spare loom from ecu to bulkhead if all goes well tomorrow.

[Twin pipe]

Toadusmodus said:

Graham, have a look at http://www.pistonheads.com/gassing/topic.asp?h=0&a...

I got the whole thing from http://www.douglasvalley.co.uk/. My car has the connection under the expansion tank in the engine compartment, but I have bought the single piece loom. Not cheap though! Give them a call, but I may have a spare loom from ecu to bulkhead if all goes well tomorrow.

Thanks Toadusmodus, let me know on your 2-piece section and your cars progress.

Edited by Twin pipe on Monday 28th May 22:38

Edited by Twin pipe on Monday 28th May 22:44

[Toadusmodus]

Got it done. http://www.pistonheads.com/gassing/topic.asp?h=0&a...

I have the half of the loom that goes from the bulkhead to the ecu if you want it. The other half is slightly the worse for wear after I removed it!! Will email you later with details.