Ferrari 308 early V8 twin distributor ignition upgrades ??
Discussion
Hi
I've been asked by a friend of a friend if I know anything about upgrades to early 308 V8 ignition systems. The owner says that his 308 suffers from reasonably frequent points and condensor failures, which isn't a problem apart from having to have them replaced. I don't know much about Ferrari's of any kind, but I understand it's got twin coils and twin distributors, so in effect it's ignition is like two 4 pots, and it has balasted ignition system, so the coils see full voltage to start then drop back through the resistor when running. This could be what is failing to return to balasted voltage, over-voltaging the coils and burning out the points.
I'm sure it could be made to run 12v coils but I wonder if there is a sympathetic upgrade to remove or replace the points for something more modern but retaining the look of original equipment as the car is apparently a mint early example.
Any thoughts, suggestions, experience ??
Phil.
I've been asked by a friend of a friend if I know anything about upgrades to early 308 V8 ignition systems. The owner says that his 308 suffers from reasonably frequent points and condensor failures, which isn't a problem apart from having to have them replaced. I don't know much about Ferrari's of any kind, but I understand it's got twin coils and twin distributors, so in effect it's ignition is like two 4 pots, and it has balasted ignition system, so the coils see full voltage to start then drop back through the resistor when running. This could be what is failing to return to balasted voltage, over-voltaging the coils and burning out the points.
I'm sure it could be made to run 12v coils but I wonder if there is a sympathetic upgrade to remove or replace the points for something more modern but retaining the look of original equipment as the car is apparently a mint early example.
Any thoughts, suggestions, experience ??
Phil.
There are a few options, ranging from a complete replacement with a Motec type setup (I put one in a 400i a couple of years ago and it transformed the car) but a decent standard'ish looking setup up is sold by Superfomance (bottom of the page)
http://www.superformance.co.uk/a-308/ignition.htm
http://www.superformance.co.uk/a-308/ignition.htm
Thanks Andrew.
Did you do the Motec yourself or was it done by someone else ?? And how far away from standard-looking is it ?? Wasted spark ?? Injected rather than carb ?? Easy to Map ??
Do you have any experience of the Superformance kits, either Dinoplex or BSM ?? Do they install and configure as well ??
Sorry for all the silly questions, I'm just trying to get a feel of what is on offer before I go back to the owner. He's likely to want a fully fitted option.
Thanks again.
Phil.
Did you do the Motec yourself or was it done by someone else ?? And how far away from standard-looking is it ?? Wasted spark ?? Injected rather than carb ?? Easy to Map ??
Do you have any experience of the Superformance kits, either Dinoplex or BSM ?? Do they install and configure as well ??
Sorry for all the silly questions, I'm just trying to get a feel of what is on offer before I go back to the owner. He's likely to want a fully fitted option.
Thanks again.
Phil.
Hi Johnny
I'm sure he is doing, this isn't his sole Ferrari so he has service connections in East Anglia and London. It's not like he's changing the points and condensor's himself.
It just cropped up in converstation over the weekend, and I was interested so I thought I'd enquire of the collective.
No harm asking.
Phil.
(edit for spelling)
I'm sure he is doing, this isn't his sole Ferrari so he has service connections in East Anglia and London. It's not like he's changing the points and condensor's himself.
It just cropped up in converstation over the weekend, and I was interested so I thought I'd enquire of the collective.
No harm asking.
Phil.
(edit for spelling)
Phil Hill said:
Thanks Andrew.
Did you do the Motec yourself or was it done by someone else ?? And how far away from standard-looking is it ?? Wasted spark ?? Injected rather than carb ?? Easy to Map ??
Do you have any experience of the Superformance kits, either Dinoplex or BSM ?? Do they install and configure as well ??
Sorry for all the silly questions, I'm just trying to get a feel of what is on offer before I go back to the owner. He's likely to want a fully fitted option.
Thanks again.
Phil.
Yes we did do the Motec upgrade; it's nowhere near standard looking, as we had to swap from the very early Bosch injection to throttle bodies. the actual setup of the solution was relatively simple.Did you do the Motec yourself or was it done by someone else ?? And how far away from standard-looking is it ?? Wasted spark ?? Injected rather than carb ?? Easy to Map ??
Do you have any experience of the Superformance kits, either Dinoplex or BSM ?? Do they install and configure as well ??
Sorry for all the silly questions, I'm just trying to get a feel of what is on offer before I go back to the owner. He's likely to want a fully fitted option.
Thanks again.
Phil.
I've used the BSM system, which is basically the same as the electronic distributor kits used in many other classics, whilst it's not as tweakable as something like Motec, it can be fitted in such a way as to make the install look OEM
The Dinoplex solution, is just the factory system
AndrewW-G said:
Yes we did do the Motec upgrade; it's nowhere near standard looking, as we had to swap from the very early Bosch injection to throttle bodies. the actual setup of the solution was relatively simple.
I've used the BSM system, which is basically the same as the electronic distributor kits used in many other classics, whilst it's not as tweakable as something like Motec, it can be fitted in such a way as to make the install look OEM
The Dinoplex solution, is just the factory system
Thanks for clarifying Andrew.I've used the BSM system, which is basically the same as the electronic distributor kits used in many other classics, whilst it's not as tweakable as something like Motec, it can be fitted in such a way as to make the install look OEM
The Dinoplex solution, is just the factory system
I think the owner will want something standard looking so it looks like the BSM is favourite.
Phil.
I believe Pertronix does a transistor points kit, but I think it's only for the single distributor model.
http://classicgarage.com/fe308gtbeumo.html
Lee
http://classicgarage.com/fe308gtbeumo.html
Lee
Gassing Station | Supercar General | Top of Page | What's New | My Stuff


