F355 manifolds
Author
Discussion

Andyandyhall

Original Poster:

118 posts

169 months

Monday 11th March 2013
quotequote all
I have a 1999 Ferrari F355 Spider, should I change my manifolds as a precaution? I have read of problems with blown manifolds/headers.
As yet there are no signs of this with mine.

If so any recommendations? The car is all OEM exhaust.

theRossatron

1,032 posts

263 months

Monday 11th March 2013
quotequote all
I'm not sure its worth changing as a precaution unless you plan on swapping them out of the one of the more durable aftermarket ones such as the Tubi or Fabspeed. QV do reconditioned manifolds for around £500 a side but these are also known to fail occasionally.

The Tubi's have integrated heat shields but are very expensive. The Fabspeed are slightly less expensive but are 4-2-1 so a different setup from the factory headers which apparently affects midrange torque and exhaust note (though you gain up top), they also don't have heat-shields and are supplied with separate shields for the alternator.

Andyandyhall

Original Poster:

118 posts

169 months

Monday 11th March 2013
quotequote all
Thanks for the info. I've heard good/bad about fabspeed, a lot being that they are manufactured in Taiwan.
My issue is that I will get a Capristo when funds allow but surprisingly Capristo say that the OEM headers are ok so long as an additional exhaust valve is used. If I go down this route I will need to recon/replace my old headers using Quicksilver/Fabspeed. Tubi would be great but teamed with a Capristo it is a wallet burner.

If anyone has been in a similar situation all feedback is appreciated.

Cerbieherts

1,652 posts

172 months

Monday 11th March 2013
quotequote all
I've no direct experience with Fabspeed products but all the conflicting reports about quality pose concerns. I've never had a single issue with Capristo or quicksilver products in many years of fitting both. The OE units have very thin-walled tubing, and I don't believe repair is a good long term solution. If you have concerns regarding your manifolds there are several tests that can be carried out to check their integrity, so you should ask for these to be carried out next service. I have repaired a fair few 355 engines due to the after affects of leaking manifolds and it isn't cheap!

Andyandyhall

Original Poster:

118 posts

169 months

Monday 11th March 2013
quotequote all
Cerbieherts said:
I've no direct experience with Fabspeed products but all the conflicting reports about quality pose concerns. I've never had a single issue with Capristo or quicksilver products in many years of fitting both. The OE units have very thin-walled tubing, and I don't believe repair is a good long term solution. If you have concerns regarding your manifolds there are several tests that can be carried out to check their integrity, so you should ask for these to be carried out next service. I have repaired a fair few 355 engines due to the after affects of leaking manifolds and it isn't cheap!
Yep that's my fear. I think I'll go for some recond manifolds from Quicksilver. Am I correct in thinking these will be fine with a Capristo exhaust fitted at a later stage ?

Cerbieherts

1,652 posts

172 months

Monday 11th March 2013
quotequote all
Absolutely fine. They are dimensionally identical so no fitting issues. Worth exploring Tubi on the 355 as many feel they sound better than the Capristo on the 355. Also worth upgrading to the superior fail-safe Capristo exhaust valve if you end up replacing the lot.

Andyandyhall

Original Poster:

118 posts

169 months

Monday 11th March 2013
quotequote all
Cerbieherts said:
Absolutely fine. They are dimensionally identical so no fitting issues. Worth exploring Tubi on the 355 as many feel they sound better than the Capristo on the 355. Also worth upgrading to the superior fail-safe Capristo exhaust valve if you end up replacing the lot.
Great, many thanks.

Jonty355

4,423 posts

244 months

Saturday 23rd March 2013
quotequote all
est thing is just to get them reconditioned if they go wrong. I had mine done by JP Exhausts and can very much recommend them. Far cheaper than an aftermarket manifold, and supposedly far more durable than the standard manifolds.

I have a tubi on my car, and this is a video of the noise it makes!!!!

http://www.youtube.com/watch?v=dObIU0c4zjM

bryn_p

468 posts

260 months

Thursday 16th January 2014
quotequote all
Cerbieherts said:
I've no direct experience with Fabspeed products but all the conflicting reports about quality pose concerns. I've never had a single issue with Capristo or quicksilver products in many years of fitting both. The OE units have very thin-walled tubing, and I don't believe repair is a good long term solution. If you have concerns regarding your manifolds there are several tests that can be carried out to check their integrity, so you should ask for these to be carried out next service. I have repaired a fair few 355 engines due to the after affects of leaking manifolds and it isn't cheap!
Dragging up an old thread here but what are the after effects of a leaking manifold?

Cheers,
Bryn

Steve12NG

341 posts

183 months

Thursday 16th January 2014
quotequote all
I have heard that Ferrari have recently "re-designed" their 355 headers and they are now much improved as well as being substantially cheaper than Tubi etc.

Anyone know anything definitive about this?

I have OEM headers with Hyperflow cats and Nouvalari exhaust on my '98 F1 GTS, and no issues at all at the moment but reading the various stories re OEM headers make me interested in the options.

TISPKJ

3,780 posts

238 months

Thursday 16th January 2014
quotequote all
bryn_p said:
Cerbieherts said:
I've no direct experience with Fabspeed products but all the conflicting reports about quality pose concerns. I've never had a single issue with Capristo or quicksilver products in many years of fitting both. The OE units have very thin-walled tubing, and I don't believe repair is a good long term solution. If you have concerns regarding your manifolds there are several tests that can be carried out to check their integrity, so you should ask for these to be carried out next service. I have repaired a fair few 355 engines due to the after affects of leaking manifolds and it isn't cheap!
Dragging up an old thread here but what are the after effects of a leaking manifold?

Cheers,
Bryn
In short, sucking back in broken bits of manifold and cats into the engine.

spice

654 posts

301 months

Thursday 16th January 2014
quotequote all

Seca headers , decat pipes, valve and stage 3 all from Capristio , sound is epic

spice

654 posts

301 months

Thursday 16th January 2014
quotequote all

spice

654 posts

301 months

Thursday 16th January 2014
quotequote all

spice

654 posts

301 months

Thursday 16th January 2014
quotequote all

spice

654 posts

301 months

Thursday 16th January 2014
quotequote all

spice

654 posts

301 months

Friday 17th January 2014
quotequote all
actually exhaust is stage 1

JMP86

215 posts

177 months

Friday 17th January 2014
quotequote all
These pics are useless without a sound clip!

Lovely looking set up now lets hear it.

Mario149

7,789 posts

209 months

Saturday 18th January 2014
quotequote all
In the interests of helping people decide (i.e. any old excuse biggrin), here's my previous old girl on Capristo Level 2s and test pipes:

http://www.youtube.com/watch?v=h-fQjrO0NjQ
&
http://www.youtube.com/watch?v=CKPr4xcoNTo
&
http://www.youtube.com/watch?v=1PFWWfW5lDE

<Sigh> I do miss her sometimes frown

Also, I had my manifolds reconditioned, I think by JP Exhausts also, a few years ago, was something like £700/side FWIW

ETA: I still get shivers when I hear her sound on video. In truth, I think it might be the best sounding road car exhaust ever cloud9

Edited by Mario149 on Saturday 18th January 18:53