Gallardo misfire sensor tubes,and wiper blades,alternatives
Discussion
Hey guys,not a biggie but you can save a bit.
I made up a couple of cat sensor tubes with some 3/16th brake pipe.
The tube nut is m10x1.25 pitch thread.
Slide em on the tube,flare the ends and you have two tubes ready to go
for under £10.
The alloy pipe seems tough,but if it can`t take the heat i`ll remake them in
stainless.
If you dont have the tools i could make some up for you if your desperate.
Wiper blades,happened to notice the blades on a f*** focus looked exactly the same
as the lambo ones,so popped down to local dealer,quick measure yep 26" nice.
Not real cheap at £60 the pair,but less than half price for lambo ones.
Make no mistake,these are exactly the same, they also have a wear sensor on them.
You have to get two drivers side blades,cos on a focus the pass side is shorter.
Hope this helps someone out.Cheers
I made up a couple of cat sensor tubes with some 3/16th brake pipe.
The tube nut is m10x1.25 pitch thread.
Slide em on the tube,flare the ends and you have two tubes ready to go
for under £10.
The alloy pipe seems tough,but if it can`t take the heat i`ll remake them in
stainless.
If you dont have the tools i could make some up for you if your desperate.
Wiper blades,happened to notice the blades on a f*** focus looked exactly the same
as the lambo ones,so popped down to local dealer,quick measure yep 26" nice.
Not real cheap at £60 the pair,but less than half price for lambo ones.
Make no mistake,these are exactly the same, they also have a wear sensor on them.
You have to get two drivers side blades,cos on a focus the pass side is shorter.
Hope this helps someone out.Cheers
V10 BAT said:
Hey guys,not a biggie but you can save a bit.
I made up a couple of cat sensor tubes with some 3/16th brake pipe.
The tube nut is m10x1.25 pitch thread.
Slide em on the tube,flare the ends and you have two tubes ready to go
for under £10.
The alloy pipe seems tough,but if it can`t take the heat i`ll remake them in
stainless.
If you dont have the tools i could make some up for you if your desperate.
Wiper blades,happened to notice the blades on a f*** focus looked exactly the same
as the lambo ones,so popped down to local dealer,quick measure yep 26" nice.
Not real cheap at £60 the pair,but less than half price for lambo ones.
Make no mistake,these are exactly the same, they also have a wear sensor on them.
You have to get two drivers side blades,cos on a focus the pass side is shorter.
Hope this helps someone out.Cheers
hi mate these pipes are they ok to use for the misfire tubes can they withstand the heat. regardsI made up a couple of cat sensor tubes with some 3/16th brake pipe.
The tube nut is m10x1.25 pitch thread.
Slide em on the tube,flare the ends and you have two tubes ready to go
for under £10.
The alloy pipe seems tough,but if it can`t take the heat i`ll remake them in
stainless.
If you dont have the tools i could make some up for you if your desperate.
Wiper blades,happened to notice the blades on a f*** focus looked exactly the same
as the lambo ones,so popped down to local dealer,quick measure yep 26" nice.
Not real cheap at £60 the pair,but less than half price for lambo ones.
Make no mistake,these are exactly the same, they also have a wear sensor on them.
You have to get two drivers side blades,cos on a focus the pass side is shorter.
Hope this helps someone out.Cheers
amar
Gassing Station | Supercar General | Top of Page | What's New | My Stuff