I may need some help, I ve bought a non running Mini !
Discussion
Ok it was cheap and I know these can be trouble, someone in the village has it stuck in their garage and was looking for scrap money, I said I’ll have it unseen, I’ve not seen the car yet.
All I know so far is it’s a Mini cooper convertible, I think 11 plate. It was running but engine lights came on and I think overheating.
Some wires have been disconnected and they are not sure where they go as the connections are the same and reach different plugs. And I think it’s around 50k miles.
Hopefully I’ll get it home this week and start investigating.
All I know so far is it’s a Mini cooper convertible, I think 11 plate. It was running but engine lights came on and I think overheating.
Some wires have been disconnected and they are not sure where they go as the connections are the same and reach different plugs. And I think it’s around 50k miles.
Hopefully I’ll get it home this week and start investigating.
Not started that well, I went to collect but the battery was showing 0 volts and the steering lock wouldn’t disengage with a booster battery. (It’s in a lock up so couldn't manoeuvre it out)
On a plus note it is a 2011 cooper S with 54k on the clock.
New battery ordered and I’ll try again when it arrives.
On a plus note it is a 2011 cooper S with 54k on the clock.
New battery ordered and I’ll try again when it arrives.
I didn’t see the booster so can’t help sorry.
Good news is it’s not a non runner, new battery arrived (thanks Tanya) popped that on and it started so I drove it the 100yds home.
Bad bits,
No coolant, everything loose or unplugged around it, Pattern thermostat housing fitted but apparently its not right.
I have the old original part so I think I'll get the pattern one of and start from there.
Original

Good news is it’s not a non runner, new battery arrived (thanks Tanya) popped that on and it started so I drove it the 100yds home.
Bad bits,
No coolant, everything loose or unplugged around it, Pattern thermostat housing fitted but apparently its not right.
I have the old original part so I think I'll get the pattern one of and start from there.
Original
Will do, just waiting for parts now. The guy I bought it of is quite a good motorcycle mechanic but hates working cars with a passion, he change the thermostat but couldn't stop it leaking, I think the cause of that is the pattern part he had, one of the 5 pipes that you connect a hose too, is undersized, not realising that he then replace the spring clamp with a jubilee and it still leaked.

Top is the leaky one, bottom is the pattern with undersized outlet.
Top is the leaky one, bottom is the pattern with undersized outlet.
I’ve got it all up and running, haven’t driven it yet as the mot is out. I got the V5 yesterday it’s an 11 plate R57 convertible, Cooper S 184bhp, 1 lady owner with 55k on the clock, and the no plate valued by reg transfers at £800 !
3 problems on scanning, 2 bulbs that were a complete @£&# to fix and rear pads.
I was just going to do the pads but with a wife and 3 daughters all looking at it saying it would be a nice car to keep, I think new disc and pads all round.
Another job that needs doing is the rubber seal around the rear of the hood, apart from that it’s pretty mint.
3 problems on scanning, 2 bulbs that were a complete @£&# to fix and rear pads.
I was just going to do the pads but with a wife and 3 daughters all looking at it saying it would be a nice car to keep, I think new disc and pads all round.
Another job that needs doing is the rubber seal around the rear of the hood, apart from that it’s pretty mint.
Started changing the rear pads but the discs had seen better days, then the calipers, seals had gone and rust on the piston, so new calipers pads and discs, only fiddly bit was fitting the pad wear sensor.
Big day tomorrow, mot day, it will also be the first drive so I’m hoping the head gasket hasn’t gone from when the thermostat failed.
Big day tomorrow, mot day, it will also be the first drive so I’m hoping the head gasket hasn’t gone from when the thermostat failed.
Gassing Station | Engines & Drivetrain | Top of Page | What's New | My Stuff



