I thought its worth me piping up.

[Behold81]

So in my other post I mentioned the incredibly cheap 1 7/8 to 3.5 proflow headers. So they turned up after 6 days in FedEx hands.

Overall I'm very pleased. Full photos on here. With pics of the welds and downsize pipes https://www.facebook.com/media/set/?set=a.44067546...

For the purpose of this post couple attached below.

The pipes are stainless and are not magnetic so should be an ok grade. The flanges look to be steel. Welds are ok. Nothing special but clean. The collector is to really the poor bit but nothing looks like it would cause a performance issue. The collector seems like it will flow well enough. TBH if there was a need to push a 3.5 inch exhaust I would get them reworked. But at 1/2 to 1/3 of the price of any other headers this size.....

Looking at the inside welds there clean and smooth making for good flow too. For those interested I will have these at SRR on Saturday for anyone interested in looking at them. They also do VY and VE sets.

The downsize pipes are clean too and look show the welding off well.

[jameshsv]

they look nice how much!

[VinceM]

jameshsv said:

they look nice how much!

Wot he said!

[gsd2000]

What was the final cost shipped and taxed

[gsd2000]

So 304 stainless aswell, nice

[stick100]

For the price off them they look good mate get them fitted

[Behold81]

Including the extended lambda looms it was 915AUD delivered? I have not received a tax bill yet.

If i do get taxed it should be about 650ish with the exchange rate. BARGAIN.....

[Behold81]

stick100 said:

For the price off them they look good mate get them fitted

Hoping to be fitted within 2 weeks.

[luisv8]

Well I can't afford it but misses keeps asking me what I want for xmas that's really good price. Got a link/company name? When u say loom, what u mean? What loom do u need with headers?

[stick100]

luisv8 said:

Well I can't afford it but misses keeps asking me what I want for xmas that's really good price. Got a link/company name? When u say loom, what u mean? What loom do u need with headers?

You well need a extension loom for the front lambas

[jameshsv]

Behold81 said:

Including the extended lambda looms it was 915AUD delivered? I have not received a tax bill yet.

If i do get taxed it should be about 650ish with the exchange rate. BARGAIN.....

THATS VERY GOOD for 17/8 all in

[Behold81]

The company I used was VPW.com.au. Speak to Joe or Aaron and tell them I recommended them. You will need to pay using Bank transfer.

As to the loom. It's just a short extension. Not a great photo but there just that. At 21AUD each it was worth it.

[Behold81]

jameshsv said:

THATS VERY GOOD for 17/8 all in

Yes it is. In stainless that would be nearer 1600+

[gsd2000]

Might be worth seeing how much it would cost to bring a few sets over. Hopefully the shipping cost should be reduced per item

[stigmundfreud]

wait until you fit them before you raise your praise based on the price! Hope they fit nicely

[Behold81]

stigmundfreud said:

wait until you fit them before you raise your praise based on the price! Hope they fit nicely

You make a good point! Online forum comments only shows one guy will issues. Others have had no issues.

[jameshsv]

Behold81 said:

You make a good point! Online forum comments only shows one guy will issues. Others have had no issues.

Hurry up and fit them

[Behold81]

I will!

Week after SRR

[MyM8V8]

These Chinese made Pro Flow headers (I am told on good authority) are a pretty close copy of the Pacemaker headers - apart from that collector - which isn't too bad I suppose.

I am talking to a company in Oz about a group buy.

Edited by MyM8V8 on Tuesday 29th October 01:28

[rich24v]

Ant,
I assume you will bring these headers to SRR for others to have a look at, can you bring your act clutch aswell, I'd like to compare to the ls9 clutch which I'll have in my boot, perhaps others might want a look too....