Rising idle speed. Help!
Rising idle speed. Help!
Author
Discussion

rickf_uk

Original Poster:

420 posts

219 months

Sunday 3rd November 2013
quotequote all
Of late the 'Ro has started to develop a bit of nagging problem. When I put the car into neutral the revs are very slow to fall back to idle. At first it stays up at around 1700 revs and then slowly falls back to 1500, hesitates, and then slowly falls back to around 1100. Whats worse is that its seams to be getting worse and the initial 'idle' is creeping up to around 2000rpm. I don't thinks its a sticky throttle cable (2004 car) and could do with some pistonheads expert input.

crisisjez

9,209 posts

236 months

Sunday 3rd November 2013
quotequote all
rickf_uk said:
Of late the 'Ro has started to develop a bit of nagging problem. When I put the car into neutral the revs are very slow to fall back to idle. At first it stays up at around 1700 revs and then slowly falls back to 1500, hesitates, and then slowly falls back to around 1100. Whats worse is that its seams to be getting worse and the initial 'idle' is creeping up to around 2000rpm. I don't thinks its a sticky throttle cable (2004 car) and could do with some pistonheads expert input.
Sounds like a sticky throttle body, unless you have had it serviced recently and someone's been at the ecu.(throttle cracker)

Behold81

2,931 posts

200 months

Sunday 3rd November 2013
quotequote all
My recent issue was due to a leak in the intake. Worth looking at.


BUCKLE vxgts

107 posts

172 months

Sunday 3rd November 2013
quotequote all
Throttle position sensor

ringram

14,702 posts

279 months

Sunday 3rd November 2013
quotequote all
Id go with jez's diag. Remove and clean out the IAC motor housing and pintle.

Thats what deals with idle management. If its gummed up it might slow its action down.


rickf_uk

Original Poster:

420 posts

219 months

Saturday 11th January 2014
quotequote all
Sorry to bother you again guys but I'm not getting to the bottom of this problem. So far

1. Changed the IAC
2. Changed the TPS
3. Adjusted the throttle blade
4. Replaced the O2 sensors.

It might be my imagination but the car does feel better when on the move but the second I put it into neutral the revs jump up to around 2000 rpm and fall back over the next 20 seconds or so. It's driving me mad. Does anyone have any other ideas about sorting this one? Alternatively can any one suggest a suitable garage in the North West that would look at it?

gsd2000

11,515 posts

214 months

Saturday 11th January 2014
quotequote all
Mine does exactly the same thing. I was going to buy a new throttle body as I thought it was sticking but im not sure if its the cable

If mine sits at around 1700 and I blip the throttle I can usually bring it back to idle

rickf_uk

Original Poster:

420 posts

219 months

Saturday 11th January 2014
quotequote all
Hi G

At least I'm in good company.


FoxdieUK

441 posts

171 months

Saturday 11th January 2014
quotequote all
Do the 'Ros have an idle stepper motor adjuster? Could need cleaning or replacing.

IanLWarrington

390 posts

198 months

Saturday 11th January 2014
quotequote all
rickf_uk said:
Sorry to bother you again guys but I'm not getting to the bottom of this problem. So far

1. Changed the IAC
2. Changed the TPS
3. Adjusted the throttle blade
4. Replaced the O2 sensors.

It might be my imagination but the car does feel better when on the move but the second I put it into neutral the revs jump up to around 2000 rpm and fall back over the next 20 seconds or so. It's driving me mad. Does anyone have any other ideas about sorting this one? Alternatively can any one suggest a suitable garage in the North West that would look at it?
MW Performance, Chester

http://www.mwperformance.co.uk/

Monaro5.7

7,337 posts

210 months

Saturday 11th January 2014
quotequote all
gsd2000 said:
Mine does exactly the same thing. I was going to buy a new throttle body as I thought it was sticking but im not sure if its the cable

If mine sits at around 1700 and I blip the throttle I can usually bring it back to idle
You sure there is no socks in ur throttle body winkhehe

Behold81

2,931 posts

200 months

Sunday 12th January 2014
quotequote all
Personally I still think you have a leak in the manifold somewhere. Have you checked the PCV system has no leaks or perished hoses? Check the vacume hosing and map sensor is intact. Your intake gaskets might be shot. Although would only think you we suddenly get a leak if you have had it off recently.

Not sure where else you can get a leak.

gsd2000

11,515 posts

214 months

Sunday 12th January 2014
quotequote all
Monaro5.7 said:
gsd2000 said:
Mine does exactly the same thing. I was going to buy a new throttle body as I thought it was sticking but im not sure if its the cable

If mine sits at around 1700 and I blip the throttle I can usually bring it back to idle
You sure there is no socks in ur throttle body winkhehe
just checked and no socks or airfliters jammed in there.

You lot are never going to let me forget that

rickf_uk

Original Poster:

420 posts

219 months

Sunday 12th January 2014
quotequote all
Hi Behold,

I don't think its a leak. The strange thing is when the car is in gear I can get the revs to fall all the way down to around 600rpm but as soon as its in neutral the revs jump straight back to 2000rpm.

Behold81

2,931 posts

200 months

Sunday 12th January 2014
quotequote all
Yup mine was the same. Fine in gear but neutral would hang for 10secs ish. Then drop. In gear I could get it to roll along at 600rpm.

If you clutch in will it idle ok? Or same as neutral?

rickf_uk

Original Poster:

420 posts

219 months

Sunday 12th January 2014
quotequote all
Hi Behold

The revs jump up as soon as I put the clutch in. I've had couple of hours with the bonnet up this afternoon so heres we I am at the moment.

I carried out the TPS and IAC reset procedure but no real help. I've taken the induction pipe off the throttle body and I can't see any build up that would impede the closure of the throttle plate and its seems to be closing without any problems. Now, if I rev the engine it holds at 2000rpm but the moment I block off the hole in the throttle plate with my finger the revs drop right off to where they should be.

I've got a scan gauge in the car and I've monitored the IAC position. As soon as the car is put into neutral I'm getting an IAC reading of between 93-110 depending on the the engines revs when I shift to neutral. This is then taking seven seconds to drop back to zero at which point the car is idling at around 1300 rpm.

My throttle position is reading 0 (but to be honest I'm not sure I trust the scanguage on that) and I'm getting a reading of .70 volts to the TPS. Battery seems OK at 13.9 volts.

So, I'm thinking that the fault lies with the IAC. I replaced the old IAC with a brand new one so I don't think its the unit itself. Could it be that the IAC motor isn't getting enough power to perform properly?

Behold81

2,931 posts

200 months

Sunday 12th January 2014
quotequote all
The likely hood that 2 IAC's are faulty although possible is rare. Unmetered air causes the IAC to have to overcompensate. The IAC seems quite lazy on these cars hence the about 10 sec recovery. If the IAC was not working then it would stay high.

The TPS if faulty would hold it high I believe.

The TB issues you can get is the same as an airleak. The TPS thinks its zero but it's still letting in air. The issue is its hard to pressure up the intake to find the issue.

The one thing no one has mentioned is the MAF. This could be faulty.

ringram

14,702 posts

279 months

Sunday 12th January 2014
quotequote all
Who said to swap everything!?

Did you clean out the IAC cavity?

Also Behold is right check for vacuum leaks, that was his issue. Check the vac pipes at the rear.
Also with a scanner check manifold vacuum.

Has it had a tune? Try a PCM reset. But if you did nothing and the next day/week it started, then look for a mechanical issue IMO.

Vacuum leak, clogged iac etc.