Bought a ford
Author
Discussion

M11 MFP

Original Poster:

688 posts

224 months

Monday 30th December 2013
quotequote all
Well sort of... Dry sump Roush/Ford 351w, 4 speed jerico/toploader, twinplate clutch and a 9 inch coil sprung live axle.

Makes the Monaro seem refined and sophisticated.





Doesn't start well at present. Two pumps of fuel and it fires instantly and dies. If you try to keep your toe in a bit an instant carb fire results.

Fuel from the Holley blue smack on 6 psi. So it could be primary jetting or bad ignition timing.

Cold weather + Chokeless Holley double pumper with mechanical secondaries and a 1 inch throttle travel may also be a factor. Probably has quite a big cam too.

I have some 100 octane leaded so may try that.

Anyone on here have a theory?

edgun

405 posts

167 months

Monday 30th December 2013
quotequote all
I see a monaro in the background,don't like the red wheels though!

richie slow

7,570 posts

195 months

Monday 30th December 2013
quotequote all
The Monaro in the background has saved the thread.

Normally a title like that would get numerous requests for thread deletion eek

M11 MFP

Original Poster:

688 posts

224 months

Monday 30th December 2013
quotequote all
richie slow said:
The Monaro in the background has saved the thread.

Normally a title like that would get numerous requests for thread deletion eek
I've still got the monaro obviously! The toy tractor in the background is more advanced than both... Cvt transmission biggrin.

Know anything about four barrel carbs / distributors then Richie?

edgun

405 posts

167 months

Monday 30th December 2013
quotequote all
richie slow said:
The Monaro in the background has saved the thread.

Normally a title like that would get numerous requests for thread deletion eek
Did you actually see monaro

gsd2000

11,515 posts

214 months

Monday 30th December 2013
quotequote all
This a new toy then?

richie slow

7,570 posts

195 months

Monday 30th December 2013
quotequote all
M11 MFP said:
I've still got the monaro obviously! The toy tractor in the background is more advanced than both... Cvt transmission biggrin.

Know anything about four barrel carbs / distributors then Richie?
Many years ago I might have tried to help (probably fruitlessly). The only carbs I ever see nowadays are on the niece's racing mini and that's not likely to be relevant here.

Top marks for taking on what looks like a great project. Good luck with it thumbup

M11 MFP

Original Poster:

688 posts

224 months

Monday 30th December 2013
quotequote all
gsd2000 said:
This a new toy then?
Yep. Wasn't so much cash, but has a few problems as stated above. I think, fingers crossed the motor is good. Doesnt appear to have any blow by and has good oil pressure. It's certainly well used - the series they raced included pretty wild driving at times. Cost of tyres / dampers (shot I think on the front) is pretty eye watering but otherwise it's simple and built like a tank.

stick100

7,017 posts

199 months

Monday 30th December 2013
quotequote all
What race series ? I only ask as I want to do somthing like this


M11 MFP

Original Poster:

688 posts

224 months

Monday 30th December 2013
quotequote all
stick100 said:
What race series ? I only ask as I want to do somthing like this
Eurocar V8. Long defunct unfortunately and not coming back. The similar 4 cyl SHP pickups are still going strong however. This is a two seater now. Trackdays only.
Could run in CNC northern saloons etc with a total rebuild, but it wouldn't be competetive against old DTM cars etc. Also that requires a lot of money and preparation time.

stick100

7,017 posts

199 months

Monday 30th December 2013
quotequote all
[quote=M11 MFP]

Eurocar V8. Long defunct unfortunately and not coming back. The similar 4 cyl SHP pick



That's going to be a fun track day car I'm jealous

ringram

14,702 posts

279 months

Monday 30th December 2013
quotequote all
Chokeless carb is the problem IMO.
Not enough fuel, does it have a manual fitting for a choke?
Otherwise get a new carb with electric choke and jet it up nice.

Fuel wont do anything to the starting.

Probably 150rwhp wink

MyM8V8

9,468 posts

226 months

Tuesday 31st December 2013
quotequote all
Difficult not knowing any history. Try the float levels first. They are probably stuck after all this time. I'd strip and rebuild the carb first, not hard. I know a couple of guys that raced these and have been around Mallory park in one.

M11 MFP

Original Poster:

688 posts

224 months

Tuesday 31st December 2013
quotequote all
Thanks for the opinion Gareth, Rich.

Runs fine when warm, so as Richard says no choke and the lean state when cold are probably the main problem. I have a 4150 (780 cfm) elec choke holley in the garage, but its jetted for a milder 302 and has vacuum secondaries, so probably not worth the hassle. I'll look into refreshing the carb and at the choked mechanical secondary options. Also at getting the ignition and jetting set up by someone informed.

So which did you go in at Mallory Gareth? V6 or V8. Guess you got to drive - there weren't many two seaters about then.

Richard Ingram said:
Probably 150 rwhp wink
Castle Combe pre chicane, 1:04 @ 103 mph ... must go round the corners without lifting then biggrin

stigmundfreud

22,454 posts

241 months

Tuesday 31st December 2013
quotequote all
couldn't you just rejet using the current carbs jets? I'd be surprised if they were different fitments.

Also what happened to the euro v8 series? tried to read up but can't find owt. Oh and the classic minis do that speed at combe so you need to take your handbreak off wink

M11 MFP

Original Poster:

688 posts

224 months

Tuesday 31st December 2013
quotequote all
stigmundfreud said:
Also what happened to the euro v8 series?
http://www.nascarwheleneuroseries.com/cars-specs/ Still going for 2014, but these are no relation to the above. Quite a lot bigger dimensions.

MyM8V8

9,468 posts

226 months

Wednesday 1st January 2014
quotequote all
M11 MFP said:
Castle Combe pre chicane, 1:04 @ 103 mph ... must go round the corners without lifting then biggrin
If you want some help, I can put you in touch with an old mate of mine who raced them. PM me for a phone number if you need. Or try Sonny Howard of SHP Motorsport who started and ran the Eurocar series.

(BTW, I was in a V6, they fitted passenger seats for PR events, and our company sponsored the car)

Do you know whose car you have??.

M11 MFP

Original Poster:

688 posts

224 months

Wednesday 1st January 2014
quotequote all
Thanks Gareth. Sonny Howard is just up the road from me in Littleport. Wasn't going to bother him as these cars haven't been his business for many years, but thought of contacting the secretary to find the original spec / build sheet for some of the unmarked componentry, geometry etc. I know of a few people who still have them, some started a Facebook group 2 years ago. Lots of photos if you are interested.

https://www.facebook.com/eurocar.racing#!/groups/3...

Really have no idea whos car it was, there weren't many V8s with white/silver spaceframes though. Maybe Chris Dawkins?

Edited by M11 MFP on Wednesday 1st January 16:52

MyM8V8

9,468 posts

226 months

Wednesday 1st January 2014
quotequote all
M11 MFP said:
Thanks Gareth. Sonny Howard is just up the road from me in Littleport. Wasn't going to bother him as these cars haven't been his business for many years, but thought of contacting the secretary to find the original spec / build sheet for some of the unmarked componentry, geometry etc. I know of a few people who still have them, some started a Facebook group 2 years ago. Lots of photos if you are interested.

https://www.facebook.com/eurocar.racing#!/groups/3...

Really have no idea whos car it was, there weren't many V8s with white/silver spaceframes though. Maybe Chris Dawkins?

Edited by M11 MFP on Wednesday 1st January 16:52
The guys I remembered racing were Mike Jordan (Mac Tools), Stevie Hodgson, Kevin Clarke, Peter Falding and I Barry Lee, of Hot Rod racing fame, raced one too sponsored by Hewlett Packard (his was white I think).

Shame that they never really took off here, but I think they were quite expensive at the time. I think IIRC a firm called Tooheys built and prepped the F**d V8's.


Edited by MyM8V8 on Wednesday 1st January 18:56

M11 MFP

Original Poster:

688 posts

224 months

Wednesday 1st January 2014
quotequote all
MyM8V8 said:
The guys I remembered racing were Mike Jordan (Mac Tools), Stevie Hodgson, Kevin Clarke, Peter Falding and I Barry Lee, of Hot Rod racing fame, raced one too sponsored by Hewlett Packard (his was white I think).

Shame that they never really took off here, but I think they were quite expensive at the time. I think IIRC a firm called Tooheys built and prepped the F**d V8's.


Edited by MyM8V8 on Wednesday 1st January 18:56
Yep, John Toovey did the rebuilds when the crate Roush motors went tits up. Barry 'Leapy' Lee's had a blue spaceframe and sold at HH race-retro auction in fairly ropey condition about 3 years back.