90mm throttle body on 04 CV8 Ro.
90mm throttle body on 04 CV8 Ro.
Author
Discussion

MyM8V8

Original Poster:

9,468 posts

226 months

Tuesday 7th January 2014
quotequote all
Anyone tried one? Just looking at heads, cam, intake, Dus OTR and NOS for the Ro and have seen the new Edelbrock Victor LS series 90mm cable drive TB.

M11 MFP

688 posts

224 months

Tuesday 7th January 2014
quotequote all

Which head and cam combination are you looking at Gareth?

stigmundfreud

22,454 posts

241 months

Tuesday 7th January 2014
quotequote all
I bet its a set of dirty AFR's

ringram

14,702 posts

279 months

Tuesday 7th January 2014
quotequote all
Yep, fast90/90 on my GTS in the old days.
Was fine. Needs tuning obviously, but nothing tricky.

MyM8V8

Original Poster:

9,468 posts

226 months

Tuesday 7th January 2014
quotequote all
stigmundfreud said:
I bet its a set of dirty AFR's
No the CV8 is currently stock LS1 5.7. I've got a spare set of LS2 243 heads off the ute with its FAST 92 and a couple of different cams to play with. If I could get the AFRs on I would have, but they wont fit the LS1 block (needs a 4" bore)

It will also get the Wortec headers and the Duspeed OTR, all off the Ute, so all the mods are for free except for the new gaskets and bolts. I will just need to find a better cat back or get made. I also have some nice Katech Ally rocker covers with the coil mount kit so it should make the car a bit livlier. Ive already got a set of 3.73s lined up from the GTS for the rear end, again cost free apart from just replacing the 3.46's that are in. I also rebuilt a broken Tru trac from the GTS so that goes in as well.

Just wondering which cam could be best I have a nice 224-232 or a big stick I got from the Fish cheap, a while back, I know its a Texas speed but dont know the durations, I think Roger siad it was big and lumpy, probably off one of their earlier projects. It will deffo be mafless as well.

The AFRs are going on to the LS2 block with a Callies rotating kit, 402ish. I'll find something to stick it in later, most likely a 50's yank tank.

jameshsv

5,844 posts

191 months

Tuesday 7th January 2014
quotequote all
MyM8V8 said:
Anyone tried one? Just looking at heads, cam, intake, Dus OTR and NOS for the Ro and have seen the new Edelbrock Victor LS series 90mm cable drive TB.
Wich NOS kit will you be using MYM8V8

Monaro5.7

7,337 posts

210 months

Tuesday 7th January 2014
quotequote all
That cam is close to the spec of mine smile LS1 lump aswell.

223/231-112 with a 3 degree positive overlap

ringram

14,702 posts

279 months

Tuesday 7th January 2014
quotequote all
The heads are pretty woeful stock so just go with that cam IMO.
Keep the costs low. Should be fairly balanced with that cam.

jameshsv

5,844 posts

191 months

Tuesday 7th January 2014
quotequote all
If you wanted to pass those ls2 heads on nth of Watford is after a pair.

ARAF

20,759 posts

254 months

Tuesday 7th January 2014
quotequote all
jameshsv said:
If you wanted to pass those ls2 heads on nth of Watford is after a pair.
NoW has a 5.7, so has a 3.8" bore, doesn't he?

MyM8V8

Original Poster:

9,468 posts

226 months

Wednesday 8th January 2014
quotequote all
jameshsv said:
Wich NOS kit will you be using MYM8V8
I'll use a wet plate, I already have a Zex bottle and a few bits and pieces.

MyM8V8

Original Poster:

9,468 posts

226 months

Wednesday 8th January 2014
quotequote all
jameshsv said:
If you wanted to pass those ls2 heads on nth of Watford is after a pair.
I know but they are worth more to me than the market value.

Rich, the 243's have to be better than the LS1 241's

Edited by MyM8V8 on Wednesday 8th January 12:28

MyM8V8

Original Poster:

9,468 posts

226 months

Wednesday 8th January 2014
quotequote all
ARAF said:
NoW has a 5.7, so has a 3.8" bore, doesn't he?
LS2 Heads go on an LS1. Its the AFRs that have the big valves that wont fit.

N2HSV

289 posts

261 months

Wednesday 8th January 2014
quotequote all
Gareth

I have a Holley 90mm throttle body fitted.

Chris

ARAF

20,759 posts

254 months

Wednesday 8th January 2014
quotequote all
MyM8V8 said:
ARAF said:
NoW has a 5.7, so has a 3.8" bore, doesn't he?
LS2 Heads go on an LS1. Its the AFRs that have the big valves that wont fit.
Thanks. I re-read your post, and it all makes sense now. redface

ringram

14,702 posts

279 months

Wednesday 8th January 2014
quotequote all
MyM8V8 said:
I know but they are worth more to me than the market value.

Rich, the 243's have to be better than the LS1 241's

Edited by MyM8V8 on Wednesday 8th January 12:28
Yeah 230cfm vs 260cfm, more than 10% better.
But still way off "best"

That being said, most of the stuff is sensible and based on reusing parts etc. So Id keep that line of attack up and just go with the smaller cam. The larger one will want way more head to be worth while. At least with the smaller one it will run nice on the street.

Unless you want to spin buggery out of it. The yanks get 400rwhp from stock LS1 with the TRex cam. Aka 360rwhp on Oz/Charlies dyno.

The exhaust duration looks along the lines of NOS setups too. If you tune it right you might hit 400rwhp, I think I got to 385rwhp in my ls1 with a 220 cam and less lift. So maybe Ill let you have 390rwhp at a push with crapier heads wink


gsd2000

11,515 posts

214 months

Wednesday 8th January 2014
quotequote all
a bit shot of nitrous will help ALOT biggrin

MyM8V8

Original Poster:

9,468 posts

226 months

Friday 10th January 2014
quotequote all
N2HSV said:
Gareth

I have a Holley 90mm throttle body fitted.

Chris
Thanks Chris. No worries I take it?

MyM8V8

Original Poster:

9,468 posts

226 months

Friday 10th January 2014
quotequote all
ringram said:
Yeah 230cfm vs 260cfm, more than 10% better.
But still way off "best"

That being said, most of the stuff is sensible and based on reusing parts etc. So Id keep that line of attack up and just go with the smaller cam. The larger one will want way more head to be worth while. At least with the smaller one it will run nice on the street.

Unless you want to spin buggery out of it. The yanks get 400rwhp from stock LS1 with the TRex cam. Aka 360rwhp on Oz/Charlies dyno.

The exhaust duration looks along the lines of NOS setups too. If you tune it right you might hit 400rwhp, I think I got to 385rwhp in my ls1 with a 220 cam and less lift. So maybe Ill let you have 390rwhp at a push with crapier heads wink
What heads did you use, and did you have the 1.8 rockers on that one. LS2 is same as C4B spec???

gsd2000

11,515 posts

214 months

Friday 10th January 2014
quotequote all
MyM8V8 said:
ringram said:
Yeah 230cfm vs 260cfm, more than 10% better.
But still way off "best"

That being said, most of the stuff is sensible and based on reusing parts etc. So Id keep that line of attack up and just go with the smaller cam. The larger one will want way more head to be worth while. At least with the smaller one it will run nice on the street.

Unless you want to spin buggery out of it. The yanks get 400rwhp from stock LS1 with the TRex cam. Aka 360rwhp on Oz/Charlies dyno.

The exhaust duration looks along the lines of NOS setups too. If you tune it right you might hit 400rwhp, I think I got to 385rwhp in my ls1 with a 220 cam and less lift. So maybe Ill let you have 390rwhp at a push with crapier heads wink
What heads did you use, and did you have the 1.8 rockers on that one. LS2 is same as C4B spec???
i think that they were Dart heads, or edelbrock heads

C4B heads had a lower CR around 10:1 on a LS1, maybe a touch lower. I think C4B heads had ti retainers as standard

243 heads unskimmed should be around the 10:5 CR mark on an LS1 if my maths is correct