Programming New Key for VXR8
Discussion
Just ordered a new key and locking fob from Drive Vauxhall in Aldershot. Went in to get it programmed. The guy plugged it in and tried but he couldn't get it to work. He said it kept coming up with programming fault. Then said he didn't want to risk buggering up my one and only key and sent me packing. Nice guy, and at least they didn't charge me! Any ideas or do I have to drive all the way to Walkinshaw or Picadors?
If you get a new key for a monaro, it will start car without Tech 2 programming but need tech2 to program remote function or do manual synch.
Mikes new vxr8 key will not start car (dash says "car immobilised") so I am assuming that there may not be a manual way to program VXR8 key, is it tech2 only ? not sure as never had to try
Mikes new vxr8 key will not start car (dash says "car immobilised") so I am assuming that there may not be a manual way to program VXR8 key, is it tech2 only ? not sure as never had to try
After some JFGI the following information is available for you to test 
Adding Keys
Important:
• To initiate, this procedures requires that a learned master key be available.
• A total of 10 keys may be programmed to a single vehicle.
• This procedure adds keys only. The procedure does not erase previously learned keys.
• The keys to be learned must duplicate the mechanical cut of the current key.
• If more than one valet key is to be learned, immediately precede each valet key with a learned master key.
1 With a previously learned master key, turn ON the ignition, with the engine OFF.
2 Turn OFF the ignition and remove the key.
3 Within 10 seconds of turning OFF the ignition, insert the key to be learned and turn ON the ignition. The vehicle has now learned the new key.

Adding Keys
Important:
• To initiate, this procedures requires that a learned master key be available.
• A total of 10 keys may be programmed to a single vehicle.
• This procedure adds keys only. The procedure does not erase previously learned keys.
• The keys to be learned must duplicate the mechanical cut of the current key.
• If more than one valet key is to be learned, immediately precede each valet key with a learned master key.
1 With a previously learned master key, turn ON the ignition, with the engine OFF.
2 Turn OFF the ignition and remove the key.
3 Within 10 seconds of turning OFF the ignition, insert the key to be learned and turn ON the ignition. The vehicle has now learned the new key.
preciousmetal said:
If you get a new key for a monaro, it will start car without Tech 2 programming but need tech2 to program remote function or do manual synch.
Mikes new vxr8 key will not start car (dash says "car immobilised") so I am assuming that there may not be a manual way to program VXR8 key, is it tech2 only ? not sure as never had to try
I'm sure its tech2 only, the shower at Aldershot should be able to do it as they were once official dealers, say no more, (fell out big time with my 1st 8) if not Picador..........Mikes new vxr8 key will not start car (dash says "car immobilised") so I am assuming that there may not be a manual way to program VXR8 key, is it tech2 only ? not sure as never had to try

Also got this with regards to new keys in 2 parts. (pontiac G8)
A the key, B the button section.
The following procedure is for
programming additional keys only. If all vehicle keys are lost or no longer work, see your dealer/retailer.
A new key must be made prior to programming.
A maximum of four keys can be programmed for your vehicle.
The key is purchased as two sections: the key blade and
immobilizer section (A) and the remote keyless entry and remote start system section (B).
Do not join the two key sections until programming is complete.
To program a new section (A):
1. Insert the original, already programmed key into the ignition and start the engine.
If the engine does not start, see your dealer/retailer.
2. Remove the key from the ignition.
3. Insert and turn the new section (A) to ON/RUN within five seconds of removing the original key.
4. Turn the new section (A) to LOCK/OFF. Section (A) is now programmed.
To program a new section (B):
1. Turn the ignition to ON/RUN with the new section (A).
The vehicle must be in PARK (P).
2. Select Remote Key from the personalization menu.
3. Select Program.
4. Press LOCK and UNLOCK on the new section (B), at the same time,
until you hear two beeps.
5. Repeat Step 4 for all other keys, including keys that require programming or ones previously programmed to the vehicle.
Any key not reprogrammed will be erased.
6. Turn the ignition to LOCK/OFF.
7. Join sections (A) and (B) until they click.
Do not join the two key sections until programming is complete.
Do not leave the key or device that disarms or deactivates the theft deterrent system in the vehicle.
A the key, B the button section.
The following procedure is for
programming additional keys only. If all vehicle keys are lost or no longer work, see your dealer/retailer.
A new key must be made prior to programming.
A maximum of four keys can be programmed for your vehicle.
The key is purchased as two sections: the key blade and
immobilizer section (A) and the remote keyless entry and remote start system section (B).
Do not join the two key sections until programming is complete.
To program a new section (A):
1. Insert the original, already programmed key into the ignition and start the engine.
If the engine does not start, see your dealer/retailer.
2. Remove the key from the ignition.
3. Insert and turn the new section (A) to ON/RUN within five seconds of removing the original key.
4. Turn the new section (A) to LOCK/OFF. Section (A) is now programmed.
To program a new section (B):
1. Turn the ignition to ON/RUN with the new section (A).
The vehicle must be in PARK (P).
2. Select Remote Key from the personalization menu.
3. Select Program.
4. Press LOCK and UNLOCK on the new section (B), at the same time,
until you hear two beeps.
5. Repeat Step 4 for all other keys, including keys that require programming or ones previously programmed to the vehicle.
Any key not reprogrammed will be erased.
6. Turn the ignition to LOCK/OFF.
7. Join sections (A) and (B) until they click.
Do not join the two key sections until programming is complete.
Do not leave the key or device that disarms or deactivates the theft deterrent system in the vehicle.
ringram said:
Also got this with regards to new keys in 2 parts. (pontiac G8)
A the key, B the button section.
The following procedure is for
programming additional keys only. If all vehicle keys are lost or no longer work, see your dealer/retailer.
A new key must be made prior to programming.
A maximum of four keys can be programmed for your vehicle.
The key is purchased as two sections: the key blade and
immobilizer section (A) and the remote keyless entry and remote start system section (B).
Do not join the two key sections until programming is complete.
To program a new section (A):
1. Insert the original, already programmed key into the ignition and start the engine.
If the engine does not start, see your dealer/retailer.
2. Remove the key from the ignition.
3. Insert and turn the new section (A) to ON/RUN within five seconds of removing the original key.
4. Turn the new section (A) to LOCK/OFF. Section (A) is now programmed.
To program a new section (B):
1. Turn the ignition to ON/RUN with the new section (A).
The vehicle must be in PARK (P).
2. Select Remote Key from the personalization menu.
3. Select Program.
4. Press LOCK and UNLOCK on the new section (B), at the same time,
until you hear two beeps.
5. Repeat Step 4 for all other keys, including keys that require programming or ones previously programmed to the vehicle.
Any key not reprogrammed will be erased.
6. Turn the ignition to LOCK/OFF.
7. Join sections (A) and (B) until they click.
Do not join the two key sections until programming is complete.
Do not leave the key or device that disarms or deactivates the theft deterrent system in the vehicle.
Thanks guys for all the info....VERY helpful indeed..(as you guys always are)A the key, B the button section.
The following procedure is for
programming additional keys only. If all vehicle keys are lost or no longer work, see your dealer/retailer.
A new key must be made prior to programming.
A maximum of four keys can be programmed for your vehicle.
The key is purchased as two sections: the key blade and
immobilizer section (A) and the remote keyless entry and remote start system section (B).
Do not join the two key sections until programming is complete.
To program a new section (A):
1. Insert the original, already programmed key into the ignition and start the engine.
If the engine does not start, see your dealer/retailer.
2. Remove the key from the ignition.
3. Insert and turn the new section (A) to ON/RUN within five seconds of removing the original key.
4. Turn the new section (A) to LOCK/OFF. Section (A) is now programmed.
To program a new section (B):
1. Turn the ignition to ON/RUN with the new section (A).
The vehicle must be in PARK (P).
2. Select Remote Key from the personalization menu.
3. Select Program.
4. Press LOCK and UNLOCK on the new section (B), at the same time,
until you hear two beeps.
5. Repeat Step 4 for all other keys, including keys that require programming or ones previously programmed to the vehicle.
Any key not reprogrammed will be erased.
6. Turn the ignition to LOCK/OFF.
7. Join sections (A) and (B) until they click.
Do not join the two key sections until programming is complete.
Do not leave the key or device that disarms or deactivates the theft deterrent system in the vehicle.
I will try this Monday, if no joy a trip to Picadors it is!!!!
Looking forward to next weekend now!
Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff


