FAO Ringram or others - ITBs & EFI Live
FAO Ringram or others - ITBs & EFI Live
Author
Discussion

bimbleuk

Original Poster:

156 posts

256 months

Sunday 19th January 2014
quotequote all
Hmmm seems the EFI Live forum is full of diesel smokers now as no one wants to answer a simple question.

Can I run Jenvey ITBs on an LS1B PCM with a COS5 OS using A0007 as the main map?

I think that was the intention of the custom OS but just asking in case there's something I've missed to stop me doping this?

Any help appreciated.

Justin

DaciaBumdart

22,454 posts

241 months

Sunday 19th January 2014
quotequote all
Stick should be able to answer this I think he put ITB's on an LS1 and mapped it

stick100

7,017 posts

199 months

Sunday 19th January 2014
quotequote all
I didn't bother with a custom operating system the standard one will work fine as for mapping it took a while to get it about right but I had a lot of help on that from rich

DaciaBumdart

22,454 posts

241 months

Sunday 19th January 2014
quotequote all
I thought the same re custom OS but having not done it. In fact I went COS for a while but switched back for better results

ringram

14,702 posts

279 months

Sunday 19th January 2014
quotequote all
Yes, but use mafless/speed density ideally.
You can use tps only if you want, but I'd only look at that with a spastic cam that idles over 1000rpm.

ringram

14,702 posts

279 months

Sunday 19th January 2014
quotequote all
stick100 said:
I didn't bother with a custom operating system the standard one will work fine as for mapping it took a while to get it about right but I had a lot of help on that from rich
I think I flashed the custom into yours mate. But you probably didn't use those features. Except the maffless bit

stick100

7,017 posts

199 months

Sunday 19th January 2014
quotequote all
ringram said:
I think I flashed the custom into yours mate. But you probably didn't use those features. Except the maffless bit
I'm still learning on that front

But my 5.7 beat a well known 6.2 that's all I was concertrating on lol



DaciaBumdart

22,454 posts

241 months

Sunday 19th January 2014
quotequote all
ringram said:
Yes, but use mafless/speed density ideally.
You can use tps only if you want, but I'd only look at that with a spastic cam that idles over 1000rpm.
I'd say keep the maf and help stabilise the tune using the black magic then once happy do the mafless bit (if you really want to chase those final ponies)

bimbleuk

Original Poster:

156 posts

256 months

Sunday 19th January 2014
quotequote all
Thanks for the replies that's another tick on the list.

I was going to initially try Alpha-N just to get it up and running. I have access to a dyno in exchange for IT work and the operator has lots of experience in tuning so I don't have to rely on just road logging. I only drive the car (RX7) in summer anyway so that helps. Speed Density requires a MAP doesn't it so that'll need the Jenvey manifolds to be drilled n tapped.

Ultimately I was planning on making plenums, which would require curved inlet airhorns to fit under the bonnet. To do that I need to relocate the coils and remove the filler neck etc. so lots of details and time!

stick100

7,017 posts

199 months

Sunday 19th January 2014
quotequote all
bimbleuk said:
Thanks for the replies that's another tick on the list.

I was going to initially try Alpha-N just to get it up and running. I have access to a dyno in exchange for IT work and the operator has lots of experience in tuning so I don't have to rely on just road logging. I only drive the car (RX7) in summer anyway so that helps. Speed Density requires a MAP doesn't it so that'll need the Jenvey manifolds to be drilled n tapped.

Ultimately I was planning on making plenums, which would require curved inlet airhorns to fit under the bonnet. To do that I need to relocate the coils and remove the filler neck etc. so lots of details and time!
The jenveys will need abit of work for map ref and brake servo
All I did was tap a hole into each runner and connected each runner to a separate plenum to which I could plumb in a map sensor and a inlet for the servo feed

stick100

7,017 posts

199 months

Sunday 19th January 2014
quotequote all

bimbleuk

Original Poster:

156 posts

256 months

Sunday 19th January 2014
quotequote all
Cheers Stick.

Hmmm I think I may as well get them drilled while I'm ordering them and save myself some hassle.

I only need MAP as I removed the servo/ABS brakes and fitted a pedal box plus powered steering column (so no hydraulics or pump either). Also the servo would have been in the way too so now I'm glad I did that early in the build.

stick100

7,017 posts

199 months

Sunday 19th January 2014
quotequote all
bimbleuk said:
Cheers Stick.

Hmmm I think I may as well get them drilled while I'm ordering them and save myself some hassle.

I only need MAP as I removed the servo/ABS brakes and fitted a pedal box plus powered steering column (so no hydraulics or pump either). Also the servo would have been in the way too so now I'm glad I did that early in the build.
With the aus dollar rate being good at the moment see how much a harrop intake would cost

They are plug and play no need to drill/tap anything if I had known the dollar rate was going to go our way I would have waited and brought the harrop as it would have saved me alot of work

bimbleuk

Original Poster:

156 posts

256 months

Monday 20th January 2014
quotequote all
Very tidy install and a better total solution really. Currently they are the same cost at full RRP though that excludes the import, P&P plus VAT on everything! For the Harrop.

I'm getting a useful discount from my supplier and I'm not paying £50 per ram pipe! I can make them myself at the very least. Plus I mentioned earlier I may need to make curved ones to suit the bonnet.

The Jenvey setup also has some more modular options which may help me with my install such as wedges to angle the TBs. Much harder if the supplier was half way round the globe.

Justin

stick100 said:
With the aus dollar rate being good at the moment see how much a harrop intake would cost

They are plug and play no need to drill/tap anything if I had known the dollar rate was going to go our way I would have waited and brought the harrop as it would have saved me alot of work

MyM8V8

9,468 posts

226 months

Monday 20th January 2014
quotequote all
stick100 said:
With the aus dollar rate being good at the moment see how much a harrop intake would cost
AU$4950 plus shipping plus taxes.

Harrop are quite expensive for pretty much everything they do.

stick100

7,017 posts

199 months

Monday 20th January 2014
quotequote all
MyM8V8 said:
AU$4950 plus shipping plus taxes.

Harrop are quite expensive for pretty much everything they do.
When I was looking the rate was 1.38-1.45 The rate now is about 1.85 it does bring it in line with jenveys prices


Plus don't forget you don't pay aus vat if your importing over here so it's only 2675 + vat and import still a lot but the jenveys are best part of 3000 and need work

And the harrop does look the b-o-l-l-o-x

bimbleuk

Original Poster:

156 posts

256 months

Tuesday 21st January 2014
quotequote all
I ordered the Jenvey's yesterday!

Apart from having a discount from a local supplier and also my need to only buy 80% of the Jenvey kit means they were the best choice for me. For a bolt on solution though the Harrop Hurricane is certainly the most cost effective kit currently.

The was another issue I had with the Harrop and that was the 55mm throttle bodies. Basically too big for my needs. I actually wanted to downsize the TBs on the Jenvey kit to 48mm but they won't bolt to the manifold and would leave a step anyway.

I'm aiming for a good all round response and driveability (no I'm not driving miss daisy to the shops) from my install and I doubt I will be much more than mid 400's with my current heads and cam. Might seem a lot of cost/effort for that sort of power but for me it's the technical challenge just as much as the aesthetics' and noise. This is my hobby!