bARAF Pics of your ute with hardtop!
Discussion
ringram said:
Attn Ian 
How about posting some pics of your ute with the hardtop on it!?
Or are you still waiting on it?
Sorry, it was here before the Christmas meet. Dirty at the moment, but I'm test fitting new wheels on it tomorrow, and also have to take pictures of the brakes for the readers rides thread, so I'll wipe a rag over, and take some then for you. 
How about posting some pics of your ute with the hardtop on it!?
Or are you still waiting on it?

Here's one prepared earlier....
ringram said:
Yeah looks good. I can see why the HSV has a piece of extra body to transition from the lid to the rear window and roof.
But good to see you got the hump one! The flat tops look crap.
Just add some vxr8 wheels and off you go
Believe it or not, the Holden has an extra piece of bodywork as well, though not as long as the Maloo.But good to see you got the hump one! The flat tops look crap.
Just add some vxr8 wheels and off you go

AS for the VXR8 wheels - I'm not the greatest fan of the design, and I wanted to move onto 18s.
ringram said:
Whats the space behind the seats like?
Can you get anything decent in there, or is it gear in the back?
Do you use a cargo net to stop stuff sliding around?
Whats the plans drivetrain wise?

Depends how far back you have the seat, and I guess you have it back a long way. If you imagine a vertical line in front of the rear seats in your VXR8, then you're not far off. There are a couple of storage shelves behind the seats, but you also have the battery behind the passenger seat (that extends under the bed).Can you get anything decent in there, or is it gear in the back?
Do you use a cargo net to stop stuff sliding around?
Whats the plans drivetrain wise?

We just have the cargo mat in the bed. Things don't slide about, but then we don't drive in a spirited fashion with stuff in the back.
Plans are very conservative, and as funds allow. When you think that the brakes all around are over £3k, and the hard top was just under £2k, then there's not a lot left in the pot for its first year of ownership.
To start with, I'll probably go looking for the missing 80bhp - the difference between the LS3 and the L76. Intake manifold is the same, so it's not there. Exhaust headers are cast, so a set of VXR8 headers and cats are on order with another forum member. I'm not going for aftermarket headers at this time, as I'd then have to get a new full system.
I think the rest may be down to the tune, but am unsure about having it mapped, if I only have to get it mapped again when I make alterations, or decide to disable the DOD.
Intake and heads are basically the same as you say, though the valve gear is different in the ls3.
The AFM is much lower lift. IIRC 0.470 vs 0.550 in the LS3 duration maybe a bit shorter too.
You will be down ~30 BHP/FTLB due to having 20-ish cubes less
vxr8 headers are a good idea.
Check the rest of the exhaust too. Diameter etc. Some vxr8 headers and cats will probably give you a fair bit.
I suspect a tune with the current setup will then get you close if done right. Given the amount a tune normally releases.
I think compression might be down a tad too?
Cam swap will sort it out. Go for an AFM cam and keep the DoD, though the Oz crew say it doesnt save much in the way of fuel.
In which case you might be able to liberate an LS3 cam for peanuts or free. Then just pull out the lifters and associated valley parts and off you go.
Kits are around. The new LT1 handles AFM much better and the cam is larger lift-wise. Im not sure if the LT1 AFM lifters are plug and play. I seem to recollect that they are.
Its always nice to have a project.. If/when I get a ute, it will be cam and tune only. Too many logistical nightmares with parts, fitting and associated management etc.
The AFM is much lower lift. IIRC 0.470 vs 0.550 in the LS3 duration maybe a bit shorter too.
You will be down ~30 BHP/FTLB due to having 20-ish cubes less
vxr8 headers are a good idea.
Check the rest of the exhaust too. Diameter etc. Some vxr8 headers and cats will probably give you a fair bit.
I suspect a tune with the current setup will then get you close if done right. Given the amount a tune normally releases.
I think compression might be down a tad too?
Cam swap will sort it out. Go for an AFM cam and keep the DoD, though the Oz crew say it doesnt save much in the way of fuel.
In which case you might be able to liberate an LS3 cam for peanuts or free. Then just pull out the lifters and associated valley parts and off you go.
Kits are around. The new LT1 handles AFM much better and the cam is larger lift-wise. Im not sure if the LT1 AFM lifters are plug and play. I seem to recollect that they are.
Its always nice to have a project.. If/when I get a ute, it will be cam and tune only. Too many logistical nightmares with parts, fitting and associated management etc.
ringram said:
Intake and heads are basically the same as you say, though the valve gear is different in the ls3.
The AFM is much lower lift. IIRC 0.470 vs 0.550 in the LS3 duration maybe a bit shorter too.
You will be down ~30 BHP/FTLB due to having 20-ish cubes less
vxr8 headers are a good idea.
Check the rest of the exhaust too. Diameter etc. Some vxr8 headers and cats will probably give you a fair bit.
I suspect a tune with the current setup will then get you close if done right. Given the amount a tune normally releases.
I think compression might be down a tad too?
Cam swap will sort it out. Go for an AFM cam and keep the DoD, though the Oz crew say it doesnt save much in the way of fuel.
In which case you might be able to liberate an LS3 cam for peanuts or free. Then just pull out the lifters and associated valley parts and off you go.
Kits are around. The new LT1 handles AFM much better and the cam is larger lift-wise. Im not sure if the LT1 AFM lifters are plug and play. I seem to recollect that they are.
Its always nice to have a project.. If/when I get a ute, it will be cam and tune only. Too many logistical nightmares with parts, fitting and associated management etc.
I don't want to get carried away. There's no budget for anything at present bar the rear brakes and tyres for the new wheels. The AFM is much lower lift. IIRC 0.470 vs 0.550 in the LS3 duration maybe a bit shorter too.
You will be down ~30 BHP/FTLB due to having 20-ish cubes less
vxr8 headers are a good idea.
Check the rest of the exhaust too. Diameter etc. Some vxr8 headers and cats will probably give you a fair bit.
I suspect a tune with the current setup will then get you close if done right. Given the amount a tune normally releases.
I think compression might be down a tad too?
Cam swap will sort it out. Go for an AFM cam and keep the DoD, though the Oz crew say it doesnt save much in the way of fuel.
In which case you might be able to liberate an LS3 cam for peanuts or free. Then just pull out the lifters and associated valley parts and off you go.
Kits are around. The new LT1 handles AFM much better and the cam is larger lift-wise. Im not sure if the LT1 AFM lifters are plug and play. I seem to recollect that they are.
Its always nice to have a project.. If/when I get a ute, it will be cam and tune only. Too many logistical nightmares with parts, fitting and associated management etc.
The reading that I've been doing has suggested that the AFM gear is weak, above 1/2" of lift - then others have been running higher without problems, so who knows. AFM has to lift slower than conventional, so maybe those who have had problems had a profile that was too aggressive.
I do know that it's just an over-complication for little gain. If you factor in that the expertise in AFM if virtually non-existant in the UK, we're a lot better off without. I can't expect any garage to read up on everything, just for one car, so I'll probably be looking into what hardware is required to delete it at some point, but really can't see that happening for quite a while yet.
Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff





ks araf