Big problem...
Author
Discussion

djwilk

Original Poster:

1,693 posts

200 months

Monday 17th February 2014
quotequote all
Hi chaps,
I think I have just killed my mildly tuned engine...
I think it slightly overrevved and shat itself out...
I am only getting P0335 crankshaft sensor circuit A.
Apart from that the engine will not turn. Will not start, I hear a click from the starter motor and nothing else.
Left hand side exhaust bank shows bits of metal well grounded...
No oil spill.
There was a lot of smoke, I mean a lot! And that is it...

Any clues?
And what to do?
New engine?
Sell for parts?
Or what else?

mik_ok

1,580 posts

272 months

Monday 17th February 2014
quotequote all
frown

Have you removed the limiter? Or did you change down to early?

mik_ok

1,580 posts

272 months

Monday 17th February 2014
quotequote all
In your position I'd be very tempted by LS7 crate engines.....

djwilk

Original Poster:

1,693 posts

200 months

Monday 17th February 2014
quotequote all
mik_ok said:
In your position I'd be very tempted by LS7 crate engines.....
That is gotta be mega money. And I've got no repairs budget this time around.
I was accelerating in 3rd and then st went down...

mik_ok

1,580 posts

272 months

Monday 17th February 2014
quotequote all
It is a good bit more than a std / tweaked LS3.

I was looking on partsworldperformance.

So what makes you think it over-revved? The limiter is set at 6.5k which is (obviously) safe.

minime68

399 posts

166 months

Monday 17th February 2014
quotequote all
Sorry to be the bearer of bad news but it doesn't look too good from your description. Plan for the worst so you're not surprised when and if you see the carnage.

Best thing to do for the moment is maybe pull your valve covers or oil pan. That should give you a good idea of what is going on.

ringram

14,702 posts

279 months

Monday 17th February 2014
quotequote all
Dropped valve would not be unheard of or if you over revved on downshift maybe bent/bust valves.

Might just be new pistons and heads. Valve covers off for a start then maybe heads.

I doubt you would have done much on general revving as fuel cut out would have prevented you going too far.

Crate LS3 has a lot going for it.

neiljohnson

11,298 posts

238 months

Monday 17th February 2014
quotequote all
Can you turn the engine by hand?
Get a socket on the crank pulley & try turning if you can't take the plugs out if there has been a total failure of some sort the plug on the affected cylinder will normally show some form of damage


S800VXR

5,877 posts

231 months

Monday 17th February 2014
quotequote all
Pop the plugs out and take a look at them. If you have destroyed a slug or valve the plugs likely to have been taken out as well.

crisisjez

9,209 posts

236 months

Monday 17th February 2014
quotequote all
I recently bought a boroscope if that's any use once you have a plug out.
Tbh sounds like you dropped a valvefrown

ARAF

20,759 posts

254 months

Monday 17th February 2014
quotequote all
crisisjez said:
I recently bought a boroscope if that's any use once you have a plug out.
Tbh sounds like you dropped a valvefrown
To get pictures like this? (Alpina B3 #2 piston).



Sorry to hear about your problems Bart. frown As has been said, try and narrow the problem down. If you have dropped a valve, then don't try too hard to turn it, as you could well be trying to compress a valve between the piston and head.

djwilk

Original Poster:

1,693 posts

200 months

Monday 17th February 2014
quotequote all
So far I know there are metallic bits on the oil dipstick.
Will take the plugs out 2moz. Dropped valve? Would would be a reason? Rev limiter not removed. It just bounced off it and then left a cloud of smoke and its internals behind.

Also, is it worrh repairing? How much are pistons and valves? Would it cost far more to bore out or stroke it to 7.0L?
Since it's going to be in bits it may as well be a summer project. That is, if it's worrh it. Othereise I might be selling for parts. How much is it worth in the current state? Please, ignore this question I am risking having my thread closed.

ringram

14,702 posts

279 months

Monday 17th February 2014
quotequote all
piston chomped valve perhaps. I dont like fuel cut. I prefer to use the ETC to close the throttle its much softer and cleaner.
Anyway, its a perfect opportunity to do a refresh smile
Engine out for sure either way. Diag and see whats bust.
If you are lucky you can just clean the bore up to next oversize, or maybe its ok and its just piston and heads that got munched.
How much it costs will depend where you take it.

Project time!

FWIW cheapest option will be to chuck a ls3 crate into it and sell the old good bits off.

ARAF

20,759 posts

254 months

Monday 17th February 2014
quotequote all
djwilk said:
Also, is it worrh repairing? How much are pistons and valves? Would it cost far more to bore out or stroke it to 7.0L?
Since it's going to be in bits it may as well be a summer project.
There's no point in thinking about boring or stroking, until you know where the problem is.

I only rebuilt ours, as that's what SWIMBO wanted. If I had my way, it would have been in the classifieds for £12k busted (in 2011). Two and a half years further along, maybe a non-runner is worth £7k?


ArnieVXR

2,458 posts

214 months

Monday 17th February 2014
quotequote all
Is it an LS2 or LS3? I can't see scrapping it will be more cost effective than fixing it. Plenty of engines on pallets with our friendly breakers. It's only £5200 for a crate unit and you'll easily sell a battered unit.

djwilk

Original Poster:

1,693 posts

200 months

Monday 17th February 2014
quotequote all
ArnieVXR said:
Is it an LS2 or LS3? I can't see scrapping it will be more cost effective than fixing it. Plenty of engines on pallets with our friendly breakers. It's only £5200 for a crate unit and you'll easily sell a battered unit.
It is an LS3 Arnie.
£5k is a lot of dosh for a used engine of unknown lifespan. I would imagine fixing would be less than £2k if done myself?
Also, if I am going to start doing things to it, then I would like a reliable 600bhp on the fly, stroked for bags of torque smile

Araf, I could not make out what the pic of Alpina B3 was showing? I guess some sort of major damage.

Also, back on the crate engine subject and all, how much is a damaged LS3 worth to someone and assuming they would be fixing it, so could I right?

ArnieVXR

2,458 posts

214 months

Monday 17th February 2014
quotequote all
£5200 for a brand new crate LS3 - check out Gm Partsworld Performance

Value of a fubar engine depends on the damage. You needs the heads off...

djwilk

Original Poster:

1,693 posts

200 months

Monday 17th February 2014
quotequote all
ArnieVXR said:
£5200 for a brand new crate LS3 - check out Gm Partsworld Performance

Value of a fubar engine depends on the damage. You needs the heads off...
Yeah, £5k is well beyond any budget, so I guess I might be repairing or just letting it go as is.

ARAF

20,759 posts

254 months

Monday 17th February 2014
quotequote all
djwilk said:
Araf, I could not make out what the pic of Alpina B3 was showing? I guess some sort of major damage.
Sorry, no damage there. It's what a boroscope can look at. Plugs into a USB on your laptop, and you can check the bores and state of the pistons. If Jez is out of the country when you want to look, let me know and I'll pop mine in the post to you. smile

gsd2000

11,515 posts

214 months

Monday 17th February 2014
quotequote all
ARAF said:
djwilk said:
Araf, I could not make out what the pic of Alpina B3 was showing? I guess some sort of major damage.
Sorry, no damage there. It's what a boroscope can look at. Plugs into a USB on your laptop, and you can check the bores and state of the pistons. If Jez is out of the country when you want to look, let me know and I'll pop mine in the post to you. smile
great toys biggrin