Engine Analyser Pro - input data
Discussion
Has any toyed with this software? Ringram?
10 days free use, try before you buy, the results are interesting to say the least
Would be insightful if some could help confirm or provide some of the following data?
Monkfish supplied Wortec sports cat Exhaust system 2009, LS2
Header primary internal diameter:
Header primary length:
Header collector internal diameter:
Header collector length:
Exhaust system CFM:
Stock L76 or LS3 composite intake
Runner dimensions at head: 1.19" x 2.60" (Head 1.31" x 2.62")
Tappered runner? if yes what dimension at mouth:
Runner length: 10"?
Plenum dimensions:
Plenum volume:
Plenum CFM:
LS2 85mm MAF CFM: 402
LS2 90mm TB CFM: 1013
LS2 air filter CFM:
Stock L92 or LS3 cylinder head
Inlet port dimension: 2.575" tall and 1.255" wide
Intake port length:
Intake port average diameter: 1.87
Intake port volume: 260cc
Exhaust port dimension: 1.595" wide and 1.402" tall
Exhaust port dimension 1" within: 1.652" wide and 1.366" tall
Exhaust port length:
Exhaust port average diameter: 1.355
Exhaust port volume: 90cc
Thanks for any input
10 days free use, try before you buy, the results are interesting to say the least
Would be insightful if some could help confirm or provide some of the following data?
Monkfish supplied Wortec sports cat Exhaust system 2009, LS2
Header primary internal diameter:
Header primary length:
Header collector internal diameter:
Header collector length:
Exhaust system CFM:
Stock L76 or LS3 composite intake
Runner dimensions at head: 1.19" x 2.60" (Head 1.31" x 2.62")
Tappered runner? if yes what dimension at mouth:
Runner length: 10"?
Plenum dimensions:
Plenum volume:
Plenum CFM:
LS2 85mm MAF CFM: 402
LS2 90mm TB CFM: 1013
LS2 air filter CFM:
Stock L92 or LS3 cylinder head
Inlet port dimension: 2.575" tall and 1.255" wide
Intake port length:
Intake port average diameter: 1.87
Intake port volume: 260cc
Exhaust port dimension: 1.595" wide and 1.402" tall
Exhaust port dimension 1" within: 1.652" wide and 1.366" tall
Exhaust port length:
Exhaust port average diameter: 1.355
Exhaust port volume: 90cc
Thanks for any input

Added Data Edited by Gelf VXR on Saturday 22 February 02:16
Edited by Gelf VXR on Saturday 22 February 07:42
It's a good article on exhausts, it doesn't tell me technical data for my set up.
EA is a math calculator, garbage in garbage out, it's needs as precise input as possible. It's good for prediction, observing hypothetical changes, and comparing dyno plots for known set ups, getting a feel for what works, it's a bit optimistic, but it's based ideal conditions and tune
EA is a math calculator, garbage in garbage out, it's needs as precise input as possible. It's good for prediction, observing hypothetical changes, and comparing dyno plots for known set ups, getting a feel for what works, it's a bit optimistic, but it's based ideal conditions and tune
As long as you understand its just a simulation, a virtual dyno, if the data calculations for airflow and pressures equate into torque and bhp that corresponds to real world dyno data its good enough for me as an educational tool.
The software becomes useful comparing different cam profiles, head flow data, exhaust and intake changes, etc relative to a known set of data, taken in context.
For example my cam 216/228 combined with L92 heads on an LS2 bottom end show better results than data for larger duration cams, and again strong improvements to bottom end torque when I enter the data for a smaller cam described as being a stump puller 214/218.
But im not happy with the data for headers primary diameters & lengths and similarly the runners, the plenum volume in the l76 intake as taken from the limited library, hence the quest for actual measurements.
The software becomes useful comparing different cam profiles, head flow data, exhaust and intake changes, etc relative to a known set of data, taken in context.
For example my cam 216/228 combined with L92 heads on an LS2 bottom end show better results than data for larger duration cams, and again strong improvements to bottom end torque when I enter the data for a smaller cam described as being a stump puller 214/218.
But im not happy with the data for headers primary diameters & lengths and similarly the runners, the plenum volume in the l76 intake as taken from the limited library, hence the quest for actual measurements.
Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff



ks dyno bhp numbers are and they are in theory measured!