afr gauge
Author
Discussion

kaw

Original Poster:

1,081 posts

215 months

Monday 3rd March 2014
quotequote all
Looking to fit a afr gauge anyone point me in the right direction for gauge and sensor

gsd2000

11,515 posts

214 months

Monday 3rd March 2014
quotequote all
Innovate lc1 here with the innovate gauge

KMud

2,924 posts

187 months

Monday 3rd March 2014
quotequote all
Serial is nice. Innovate MTX-L here.

MyM8V8

9,468 posts

226 months

Tuesday 4th March 2014
quotequote all
I've had (and got) Innovate and the sensors don't last with them (something duff about the controllers). I'd take a look at PLX.

Loads of bad press on Innovate on Efilive forum, but good comments on PLX.

bimbleuk

156 posts

256 months

Tuesday 4th March 2014
quotequote all
Another Innovate MTX-L user here. I've been using it for the last 6 months or so with EFI Live to tune my LS motor.

Ringram supplied mine.

SturdyHSV

10,443 posts

198 months

Tuesday 4th March 2014
quotequote all
gsd2000 said:
Innovate lc1 here with the innovate gauge
Same here.

Although not fitted it yet, so it hasn't had a chance to fail hehe

KMud

2,924 posts

187 months

Tuesday 4th March 2014
quotequote all
bimbleuk said:
Ringram supplied mine.
Mine too, so biased sample!

KMud

2,924 posts

187 months

Tuesday 4th March 2014
quotequote all
At risk of bringing us O/T, how are people who are logging going about turning on their cars? The MTX-L manual says don't allow the sensor to pre-heat before turning over the engine because condensation in the exhaust can cause a shock as it hits the already-hot sensor...but that precludes turning on the ignition just the flash/piss around getting the logging started. I've got mine wired in to switched live, if I fitted a physical switch I'd probably forget, and kill the sensor by running the car without the sensor powered at all...

MyM8V8

9,468 posts

226 months

Tuesday 4th March 2014
quotequote all
KMud said:
At risk of bringing us O/T, how are people who are logging going about turning on their cars? The MTX-L manual says don't allow the sensor to pre-heat before turning over the engine because condensation in the exhaust can cause a shock as it hits the already-hot sensor...but that precludes turning on the ignition just the flash/piss around getting the logging started. I've got mine wired in to switched live, if I fitted a physical switch I'd probably forget, and kill the sensor by running the car without the sensor powered at all...
I think that the opposite of what Innovate say, but I stand to be corrected.

bimbleuk

156 posts

256 months

Tuesday 4th March 2014
quotequote all
Covering their arses maybe.

If the sensor is up front I can't see it seeing much condensation myself. Mine is quite a ways back but my car is also garaged most of the time so I don't see much condensation or pooled liquid out the back.

SturdyHSV

10,443 posts

198 months

Tuesday 4th March 2014
quotequote all
KMud said:
I've got mine wired in to switched live, if I fitted a physical switch I'd probably forget, and kill the sensor by running the car without the sensor powered at all...
To continue wading off topic, can I ask where you wired it in? Is there a particularly convenient switched live? Do you have any pics?

Given it seems relatively simple to toast the sensor, I am a little hesitant at figuring it out for myself, in case I cock it up...

Where does your gauge live?

KMud

2,924 posts

187 months

Tuesday 4th March 2014
quotequote all
SturdyHSV said:
To continue wading off topic, can I ask where you wired it in? Is there a particularly convenient switched live? Do you have any pics?

Given it seems relatively simple to toast the sensor, I am a little hesitant at figuring it out for myself, in case I cock it up...

Where does your gauge live?
The accessory socket in the centre console is my switched 12V source, and I've hacked a gauge pod onto the dash (using a panel from a breaker). Will try to get some pics of my install later, although I'm waiting on a radio pulling tool to tidy the last couple of wires.

SturdyHSV

10,443 posts

198 months

Tuesday 4th March 2014
quotequote all
KMud said:
The accessory socket in the centre console is my switched 12V source, and I've hacked a gauge pod onto the dash (using a panel from a breaker). Will try to get some pics of my install later, although I'm waiting on a radio pulling tool to tidy the last couple of wires.
I like the sound of this smile

I've got a (currently poorly put together) double din blank in place of the stereo (with a bluetooth amplifier hidden behind it) that I may stick the gauge in, got plenty of space anyway.

(excuse the purplish looking footwell glow)


The yanks have done some fairly tidy work moulding it nicely into the silver instrument surround, looks very tidy.




KMud

2,924 posts

187 months

Tuesday 4th March 2014
quotequote all
Would be easy to mount it in your blanking plate assuming you have enough depth smile

Stick did the hard bit of routing the wires from the engine bay into the car.

SturdyHSV

10,443 posts

198 months

Tuesday 4th March 2014
quotequote all
KMud said:
Would be easy to mount it in your blanking plate assuming you have enough depth smile

Stick did the hard bit of routing the wires from the engine bay into the car.
Yeah, there's plenty of room in there, my stereo is now a tiny 250g circuit board with a few components on it that's sat in the polystyrene it shipped in at the back of that cavity! hehe

Intended to mount it properly, never had the need, out of site, out of mind!

Do you mean he installed it in a different way, or that your install also required extra wiring, but stick did it?

It's been a long time since I looked at the instructions for it, is it basically use switched live from accessory socket and a ground to power the sensor, then same sort of thing with the gauge (I'll probably just nab it from the stereo's switched live?)

Was going to run cables out where the shifter is to the sensor, although may also see where the wires for the switchable exhaust run and follow them to the outside.

KMud

2,924 posts

187 months

Tuesday 4th March 2014
quotequote all
Stick and I started installing it but ran out of time, so I finished up the install at home (the easier in-cabin bits). I've got the wire to the sensor going up into the back of the engine bay, then through the grommet driver's side and underneath the dash, then the centre console. Think there was a reason we went for that rather than straight through the shifter hole, but I've forgotten already...

I think the sensor is powered directly from the gauge on the MTX-L. Tapped into switched live from the accessory socket, and ground near the fusebox. It's all pretty straightforward, the connectors won't let you go far wrong.

Note that calibration is a bit of a faff if you don't have access to a lift. Gauge on, sensor detached. Gauge on, sensor out of exhaust. Gauge on, sensor in exhaust (check the manual!).

SturdyHSV

10,443 posts

198 months

Tuesday 4th March 2014
quotequote all
KMud said:
Stick and I started installing it but ran out of time, so I finished up the install at home (the easier in-cabin bits). I've got the wire to the sensor going up into the back of the engine bay, then through the grommet driver's side and underneath the dash, then the centre console. Think there was a reason we went for that rather than straight through the shifter hole, but I've forgotten already...

I think the sensor is powered directly from the gauge on the MTX-L. Tapped into switched live from the accessory socket, and ground near the fusebox. It's all pretty straightforward, the connectors won't let you go far wrong.

Note that calibration is a bit of a faff if you don't have access to a lift. Gauge on, sensor detached. Gauge on, sensor out of exhaust. Gauge on, sensor in exhaust (check the manual!).
The calibration faff does sound familiar smile

I'd imagine going through the engine bay was chosen because the 4 bolts required to remove the shift boot are an absolute PITA to get to hehe

KMud

2,924 posts

187 months

Tuesday 4th March 2014
quotequote all

One wire left to tidy :|


I cut a small hole in the bottom of the bin (under the rubber) so I could leave the flashscan in there. The 12V plug is the dash-cam.

SturdyHSV

10,443 posts

198 months

Tuesday 4th March 2014
quotequote all
Cool thumbup

I'll be sure to post pics once mine is in smile

MadMaxHSV

1,816 posts

229 months

Wednesday 5th March 2014
quotequote all
Mounted mine per the US example.



Only annoyance with the LC1 i've found the controller errors quite easily on hard runs (overtemp sensor perhaps) and needs a power cycle to revive.